alula CAM-360-JS1 Indoor 360 Degree Security Camera Installation Guide
- June 5, 2024
- alula
Table of Contents
alula CAM-360-JS1 Indoor 360 Degree Security Camera
**CAM-360-JS1**
Save this guide for future reference
What’s in the box
Indoor 360 camera
|
Power adapter
|
Install guide
---|---|---
MicroSD card
|
Ceiling bracket
|
Hardware
Camera installation & setup
-
Power on the camera and wait for about one minute until the LED indicator blinks in a three-flash repeating pattern
-
Install the MicroSD card by gently turning the camera lens so it points upward and inserting card into slot on side of camera assembly
Camera configuration
a. Open the Alula Security app
b. In the app, browse to Cameras, then tap the `+’ icon on the top right
of the screen and follow the on-screen prompts
Don’t have the app?
Apple iOS
|
---|---
Scan the QR code for your device’s app store here
Resetting the camera
a. Keep the camera power ON for one minute. Turn the camera and find the
reset hole, which is next to the MicroSD card slot
b. Insert a paper clip or pin in the reset hole. Press and hold the reset
button for five seconds, until the LED starts flashing
c. Wait for one minute until the LED indicator blinks in a three-flash
repeating pattern
Camera setting tips
a. In case you are mounting your camera on a wall, mount the camera
around 6 feet from the ground to obtain better detection accuracy.
b. Mount the camera on a vibration-free surface
Mounting instructions
a. Place the ceiling bracket on the mounting surface as a pattern to mark
the holes
b. Drill the mounting holes and anchors to secure the bracket to the wall
c. Fasten the camera to the bracket using the tapping screws
d. Hang the camera and plate onto the hanger screws e. Arrange cable
properly so that it will not block pan/tilt operation
TRADEMARKS
Alula is a trademark owned by Alula Holdings, LLC. Wi-Fi is a trademark of The
Wi-Fi Alliance. Android is a trademark of Google LLC. IOS is a trademark of
Cisco in the U.S. and other countries and is used under license by Apple Inc.
FCC WARNING
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference. (2) This device must accept any interference that may be
received, including interference that may cause undesired operation.
Caution: any changes or modifications to this device not explicitly
approved by manufacturer could void the user’s authority to operate this
equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
| Products with CE Marking comply with EMC Directive (2014/30/EU); Low Voltage
Directive (2014/35/EU); RED (2014/53/EU); ROHS Directive (2011/65/EU) issued
by the Commission of the European Community. Compliance with these directives
implies conformity to the following European Norms:
EMC: EN 301 489
LVD: EN 62368-1
Radio: EN 300 328
---|---
| If the camera system no longer functions or can no longer be repaired, it
must be disposed of according to the valid statutory regulations. Disposal of
spent batteries/accumulators: You are required by law (Battery Ordinance) to
return all spent batteries and accumulators. Disposing of spent
batteries/accumulators with common household waste is prohibited!
Batteries/accumulators that contain hazardous substances are marked with the
symbols on the side. These symbols indicate that it is prohibited to dispose
of these batteries/accumulators in the household waste. The abbreviations for
the respective heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead. You can
return spent batteries and accumulators that can no longer be charged to the
designated collection points in your community, outlets or wherever batteries
or accumulators are sold. Following these instructions will allow you to
fulfill the legal requirements and contribute to the protection of our
environment!
Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
