alula RE206M Wireless Tilt Sensor

Tilt Sensor is a full-featured security transmitter typically used to sense the tilt of overhead garage doors and windows. It will alarm when the sensor is tilted more than 45 degrees.

Features

• Industry-leading wireless range and battery life

Enroll by placing the panel into wireless enrollment mode and then sending an enrollment signal from the sensor.

Sending an Enrollment Signal

Remove the battery tab and cover to trip tamper. Select desired Loop:

• Loop 1: Tilt Alarm when tipped to vertical
• Loop 2: Tilt Alarm when tipped to flat
• Loop 3: Not used
• Loop 4: Tamper

Install

Install by mounting the sensor to the  inside of a door or window using the mounting screw locations. For garage door installations, the sensor should be mounted to the top panel of the overhead door. This ensures that the sensor closes only when the door is fully
closed, and is best for RF range.

Tilt Detection

Tilt Detection occurs when the sensor exceeds a 45 degree angle. If the sensor rotates further than 135 degrees, it is likely to remain in a non-alarm state. For best results, the sensor should rotate within 90 degrees to ensure an alarm state occurs.

Use the panel installation guide to verify proper system setup.

Pro Tips

3M VHB Tape works great for mounting if the surface is properly prepared and firm pressure is applied for over 10 seconds.

Surface Preparation

• Clean the surface
• Ensure the mounting surface temperature is above 50 °F

Specifications

Physical

Housing Dimensions Weight with Battery Mounting Fastener

Cover-Securing Screw (optional, not provided)

| 3.25 x 1.40 x 1.05 inches (8.3 x 3.6 x 2.7 cm)

1.90 ounces (54 grams)

4 or #6 screws (not provided)

Pan Head, #1 x .25 inches, A/AB Thread Forming (sheet metal) screw, McMaster 90190A051

Environmental
Operating Temperature Maximum Humidity| 32 to 120 °F (0 to 49 °C)

85% non-condensing relative humidity

Sensor Specifications
Frequency Replacement Battery Battery Life

Battery Voltage

Current Draw Transmitted Indications

| 345 MHz

One Panasonic CR123A 10 to 15 years

3.0 VDC (Nominal), 2.2 VDC (Low)

20 mA (Maximum), 0.6 uA (Quiescent) Cover Tamper, Low Battery, Supervision

Certification
RE206M| FCC, IC

Specifications subject to change without notice.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference that may be received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by Alula could void the user’s authority to operate this equipment.
FCC ID: U5X-RE201

IC NOTICE

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

TRADEMARKS

Alula is a trademark owned by Alula Holdings, LLC. All trademarks, logos and brand names are the property of their respective owners. All company, product and service names used in this document are for identification purposes only. Use of these names, trademarks and brands does not imply endorsement.
Alula products will function with one of either Honeywell or 2GIG systems. However, no Alula product is produced by, endorsed
by, nor is officially associated with Honeywell or 2GIG. Alula recommends verifying proper enrollment and operation, per control panel installation instructions, at installation.

47-00021-02 • REV A • 2022-06-15
Tech Support Line • (888) 88-ALULA • 888-882-5852
alula.com 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>