FRONT RUNNER KVMS005T Slimpro Roof Rack

Product Information

The Front Runner Mercedes Benz Sprinter L4/H2 / 170 WB High Roof Van Rack Kit (Model: KVMS005T) is a complete kit designed to mount a rack tray or load bars onto your specific vehicle. The kit includes a Front Runner Mounting System specific to your vehicle, as well as a Front Runner Rack Tray or Load Bar Slats.

It is important to note that improper installation of this gear may void certain aspects of your warranty. It is recommended to read the fitting instructions carefully before starting the installation process. The kit contains various components including side profiles, slat assemblies, van rack wind deflector, van rack joiner kit, van track end cap, Mercedes Sprinter foot, and stud plate MB Sprinter track. The required tools for installation include a panel tool, silicone, 4mm and 5mm hex keys, a heat gun, and a 13mm wrench.

Product Usage Instructions

1. Start by opening all the Front Runner Rack Kit boxes and gather the assembly instructions for the various components.
2. Check online for the latest fitment guide at www.frontrunneroutfitters.com.
3. Get organized by arranging the components and tools needed for installation.
4. Remove the plugs from the roof of the vehicle using a heat gun to soften them and a suitable panel tool to remove them. Take care not to overheat. Refer to online videos for guidance on plug removal.
5. Assemble the Mercedes Sprinter Feet loosely using M8 x 16 Button Head Bolts and M8 Nyloc Nuts.
6. Follow the detailed assembly instructions provided in the user manual to properly install the Front Runner Mounting System specific to your vehicle.
7. Attach the Rack Tray or Load Bars to the Mounting System using the appropriate components and hardware.
8. Ensure that all components are securely fastened and tightened according to the instructions.
9. Double-check the installation to make sure it is done correctly and securely.
10. For any questions or assistance, contact Front Runner at the provided contact information.

Introduction

START HERE!
READ ME FIRST

Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain aspects of your warranty. Before you begin, take a moment and open all your Front Runner Rack Kit boxes and gather the assembly instructions for the various components.

A complete kit will contain:

1. Front Runner Mounting System specific to your vehicle
2. Front Runner Rack Tray or Load Bar Slats

This document will guide you through the assembly of the Mounting System and assist you in fitting the Rack tray or Load Bars to your specific vehicle. Please refer to the next page for a list of all the components, quantities and tools required.

IMPORTANT WARNING

IT IS CRITICAL THAT ALL FRONT-RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INST ALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INST ALLED BY A PROFESSIONAL INST ALLER OR O THER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.

IN THE BOX

1. 2 X/ Side Profile 1156mm
2. 2 X/ Side Profile 1560mm
3. 2 X/ Side Profile 1762mm
4. 12 X/ Slat Assembly
5. 1 X/ Van Rack Wind Deflector
6. 2 X/ Van Rack Joiner Kit
7. 2 X/ Van Track End Cap (Pair)
8. 8 X/ Mercedes Sprinter Foot (Pair).
9. 4 X/ Stud Plate MB Spriner Track

TOOLS NEEDED

GET ORGANIZED

INSTALLATION INSTRUCTIONS

PLUG REMOVAL

• Only remove the plugs indicated.
• Use a Heat Gun to soften the plugs and adhesive, then use a Suitable Panel tool to remove the plugs from the roof.
• Take care not to over heat. Look online for videos on how to remove the plugs.

SIDE PROFILE ASSEMBLY

• Loosely assemble the Mercedes Sprinter Feet (Item 8) using M8 x 16 Button Head Bolts, M8 Flat Washers and M8 Nyloc Nuts and slide them into the side profiles. They must still slide freely.
  • Refer to Item 8 on page 4 for assembly.
  • See 2.3 for positioning around Joiners
• Place Joiner into the Side Profile and twist into position as shown.
  • Refer to Item 6.
• Assemble the Side Profiles (Items 1, 2 & 3) using the Rack Joiners (Item 6) and M6 x 16 Button Head Bolts and fully tighten.
• See 2.3 for Side Profile orientation.
• Warning: Tightening Torque 16Nm / 11.8 ft-lbs.
• If the Vehicle has OEM tracks refer to 8.1.
• Apply Sealant around all mounting holes in the roof.
• Place pre-assembled Side Profiles over the mounting points. Align feet with factory holes and secure the feet to the roof using the 10mm Plastic Spacers, M8 x 25 Button Head Bolts, M8 x 16 Flat Washers, M8 x 25 x 2 Flat Washers and M8 Nyloc Nuts. You will need a friend to help. Fully tighten.
  • Refer to Item 8.
• Warning: Tightening Torque 25Nm / 18.4 ft lbs

WIND DEFLECTOR ASSEMBLY

• Insert two Button Head Bolts, M8 Half Nuts and M8 Schnorr Washers assemblies into the Narrow Slat as shown. Slide them to the center of the Narrow Slat (item 4), making sure that the Scnorr Washer is above the T-Slot Channel.
  • Refer to Item 5.
• Loosely assemble the M8 x 12 Button Head Bolt, M8 Schnorr Washers and M8 Thin Nut both LH & RH Wind Deflectors (Item 5) as shown.
  • Refer to Item 5.
• Slide the nut assembled to the Wind Deflector into the T-slot of the Narrow Slat as shown.
  • Refer to Item 4.

WIND DEFLECTOR FIT & SECURE

• Center the Wind Deflector on the rack and move the bolt assemblies from fig 4.1 into the slots as shown in fig 4.4.
• Leave a 10mm gap between the LH and RH Wind Deflectors and fully tighten.
  • Refer to Item 5.
  • Warning: Tightening Torque 20Nm / 14.75 ft lbs
• Loosely assemble the Slat Z Brackets (Item 4) to the Narrow Slats using M8 x 20 Hex Bolts and M8 Nyloc Nuts.
• Place the Narrow Slat End Caps on the slats (Item 4). See orientation in 5.1.
  • Refer to Item 4.

NARROW SLAT ASSEMBLY

• Loosely assemble the Slat Z Brackets (Item 4) to the Narrow Slats using M8 x 20 Hex Bolts and M8 Nyloc Nuts.
• Place the Narrow Slat End Caps on the slats (Item 4). See orientation in 5.1.
  • Refer to Item 4.

• Slide pre assembled Slats into the Side Profiles. Space the Slats at 404mm increments, or at your chosen spacing.
• These can be adjusted at any stage. Additional Slats can be added (RRNS1255 Sold Seperately).
  • Refer to Item 4.

• The Slat Z brackets can be inverted as shown if you wish to have the rack lower on your vehicle.
• If a roof A/C is fitted to the vehicle space the slats around the A/C at 202mm increments on shorter lengths and 404mm on the longer lengths
• The slats can be positioned in front and behind the A/C unit.
• Fully tighten all fasteners.
  • Warning: Tightening Torque 20Nm / 14.75 ft lbs
• Place Nut Caps over all Hex Bolts and Nyloc Nuts.

COMPLETION

• Congratulations! You did it. Take a step back and admire your work!

INSTALL OTHER ACCESSORIES

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

• Now’s the time to visit your favorite Front Runner dealer in person or online.

IMPORTANT

FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RA TING. FRONT R UNNER CANNOT BE RESPONSIBLE FOR IMPROPER LO ADING BEYOND THE VEHICLE MANUF ACTURER’S STATED LOAD CAPACITY.

OEM TRACK FITMENT

• Slide four M8 x 20 T-Bolts (RRAC907) into the vehicles OEM tracks per side.
• Place pre-assembled Side Profiles over the vehicles OEM tracks. Align feet with M8 x 20 T-Bolts (RRAC907) and secure the feet to the roof using M8 x 20 T-Bolts, M8 x 16 Flat Washers and M8 Nyloc Nuts. You will need a friend to help. Fully tighten.
  • Refer to Item 8.

Tightening Torque

• M8: 15-20Nm / 11.06 ft lb – 14.75 ft lb

Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters

BornToRoam

Share your adventures on:

© 2022 FRONT RUNNER VEHICLE OUTFITTERS.

References

• FRONTRUNNEROUTFITTERS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>