Rubine FLUSSO Series Water Heater User Manual

June 13, 2024
Rubine

Rubine logo

**LEAD THE CHANGE

WATER HEATER / PEMANAS AIR
**

USER MANUAL / PANDUAN PENGGUNA

MODEL / MODEL FLUSSO SERIES ( FS390N / FS391D )

Please read this manual thoroughly and understand the content before use.
Sila baca panduan ini dengan teliti dan memahami isi kandungannya sebelum penggunaan.

**** SAFETY PRECAUTION LANGKAH–LANGKAH KESELAMATAN

  1. Do not install reverse INLET & OUTLET and stop valve of heater.
    Jangan memasang “INLET & OUTLET” dan injap hentian pemanas dalam keadaan terbalik.

  2. Do not install the heater where there is consistent spray directly over the unit. Jangan memasang pemanas air dimana terdapat semburan konsisten terus ke atas unit.

  3. Do not connect the OUTLET to any tap or fitting that is not recommended by the manufacturer.
    Jangan sambungkan “OUTLET” pada mana-mana paip atau pemasangan yang tidak disyorkan oleh pengeluar.

  4. Do not block the heater OUTLET in any way.
    Jangan menghalang “OUTLET” pemanas dalam apa jua cara.

  5. Do not attempt to repair the heater without qualified technician. Jangan cuba untuk membaiki pemanas tanpa juruteknik yang berkelayakan.

  6. This appliance is not intended for use by person (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been supervision or instruction concerning use of the appliance by a person
    responsible for their safety.
    Perkakas ini tidak digalakkan untuk digunakan oleh orang (termasuk kanak- kanak) kurang upaya darisegi fizikal, deria atau mental, atau kurang berpengalaman atau pengetahuan, kecuali mereka diawasi atau diberi arahan mengenai penggunaan perkakas ini oleh orang yang bertanggungjawab keatas keselamatan mereka.

  7. Children should be supervised to ensure that they do not play with the appliance. Kanak-kanak hendaklah diselia untuk memastikan mereka tidak bermain dengan perkakas ini.

  8. Engage qualified electrician for installation.
    Gunakan juruelektrik yang berkelayakan untuk pemasangan.

  9. Test water temperature with hand before using the shower.
    Uji suhu air dengan menggunakan tangan sebelum menggunakan pemanas air .

  10. Check the ELCB once a month (please refer to the Test Run of Heater) and consult professional for repair if there is any malfunction.
    Pastikan ELCB diperiksa setiap bulan (sila rujuk Pengujian Pemanas) dan hubungi juruteknik untuk sebarang pembaikian.

  11. Metallic / chrome flexible hose and conductive control valve shall not be used. Saluran getah logam / krom dan injap kawalan konduktif tidak boleh digunakan.

  12. Use only new hoses to connect the appliance to the water supply. The old hose-sets should not be reused.
    Gunakan hos yang baru untuk menyambungkan perkakas kepada bekalan air. Hos yang lama tidak boleh digunakan semula.

  13. This appliance is not to be used for portable water supply.
    Alat ini tidak boleh digunakan untuk bekalan air mudah alih.

  14. Do not leave the hand shower idle in the pail. (refer below)  Jangan meninggalkan alat pancuran terbiar di dalam baldi. (rujuk dibawah)

Rubine FLUSSO Series Water Heater - untuk

WATER HEATER PARTS IDENTIFICATION

PENGENALAN BAHAGIAN – BAHAGIAN PEMANAS AIR
EXTERNAL PARTS IDENTIFICATION
PENGENALAN BAHAGIAN LUARANRubine FLUSSO Series Water Heater -
IDENTIFICATION

INTERNAL PARTS IDENTIFICATION
PENGENALAN BAHAGIAN DALAMAN
Rubine FLUSSO Series Water Heater - PARTS
IDENTIFICATION

SHOWER SET ACCESSORIES IDENTIFICATION
PENGENALAN AKSESORI PANCURANRubine FLUSSO Series Water Heater -
ACCESSORIESRubine FLUSSO Series Water Heater -
DIVERTER

GENERAL INFORMATION MAKLUMAT UMUM

INSTALLATION PEMASANGAN

CAUTION:
AWAS:
THIS APPLIANCE MUST BE EARTHED
PERKAKAS INI MESTI DIBUMIKAN

  1. All the plumbing work should be completed before proceeding to electrical wiring connection. (Table 1)
    Semua pemasangan paip perlu diselesaikan sebelum memulakan kerja-kerja penyambungan wayar elektrik. (Jadual 1)

  2. Installation must be carried out by qualified electrician with close reference to this manual and in compliance with the local regulations.
    Pemasangan mestilah dilakukan oleh juruteknik yang berkelayakan dengan merujuk pada panduan ini dan mengikut akta-akta tempatan.

  3. The unit works at minimum water flow rate of 2 litre/min, which then would trigger the built-in pump (only for pump model), boostering a stronger shower spray.
    Unit ini berfungsi pada kadar aliran air minima 2 liter/min, yang mengaktifkan pam dan kemudiannya meningkat pancuran semburan.

  4. The built-in electronic Earth Leakage Circuit Breaker (ELCB) would cut-off the power supply to heater in the event of current leakage of as low as 15mA.
    “Earth Leakage Circuit Breaker (ELCB)” akan memutuskan bekalan kuasa sekiranya berlaku kebocoran tenaga serendah 15mA

  5. The Thermal Cut-Off would automatically shut off the power supply shall there is any abnormal rise of showering temperature.
    Pemotongan haba berfungsi secara automatik akan memutuskan bekalan kuasa jika terdapat kenaikan suhu secara tidak normal.

  6. The unit only operates when there is sufficient water flow to trigger the flow switch.
    Unit hanya akan beroperasi apabila terdapat aliran air yang cukup untuk mengaktifkan suis aliran.

  7. Electrical loading Table 1:
    Pendawaian elektrik Jadual 1: Voltage
    (Vac) )| Power
    (kW)| Amperes
    (A)| Recommended Conductor Size (csa)| Fuse/ MCB(A)| ON/OFF
    Switch (A)
    ---|---|---|---|---|---
    mm2| Conduit Cable| Flexible Cable
    220 –
    50/60Hz| 4.| 16.0| 3.| 7/0.67mm| 50/0.25| 20| 20
    5.| 21.| 3.| 7/0.67mm| 56/0.30| 25| 25
    6.| 25.0| 4.0| 7/0.85mm| 56/0.30| 32| 32
    6.0| 27.| 4.0| 7/0.85mm| 56/0.30| 32| 32
    7.| 30.| 4.0| 7/0.85mm| 84/0.30| 32| 32
    8.| 34.| 6.0| 7/1.04mm| 84/0.30| 40| 40
    8.0| 36.| 6.0| 7/1.04mm| 84/0.30| 40| 40
    230 –
    50/60Hz| 4.| 15.| 3.| 7/0.67mm| 50/0.25| 20| 20
    6.| 24.0| 4.0| 7/0.85mm| 56/0.30| 32| 32
    7.| 29.| 4.0| 7/0.85mm| 56/0.30| 32| 32
    9.| 38.| 6.0| 7/1.04mm| 84/0.30| 40| 40
    240 –
    50/60Hz| 4.| 15.0| 3.| 7/0.67mm| 50/0.25| 20| 20
    4.| 18.| 3.| 7/0.67mm| 50/0.25| 20| 20
    8.| 32.| 6.0| 7/1.04mm| 84/0.30| 40| 40
    9.0| 38.| 6.0| 7/1.04mm| 84/0.30| 40| 40

  8. Instantaneous water heater shall be equipped with a 2-pole control switch and own residual current device.
    Pemanas air segera hendaklah dilengkapi dengan kawalan suis 2-kutub dan memiliki peranti arus berbaki.

  9. Water heaters exceeding 3kW shall be permanently connected to a 20A/30A rated circuit breaker/fuse with an isolator switch and residual current device.
    Pemanas air yang melebihi 3kW hendaklah disambung secara tetap pada 20A/30A nilai arus pemutus litar/fius dengan suis pengasing dan peranti arus berbaki.

INSTALLATION PROCEDURES

TATACARA PEMASANGAN

  1. INLET and OUTLET connection of the heater unit should not be  reversed, with stop valve installed on INLET. (Diagram 1) Sambungan unit pemanas “INLET” dan “OUTLET” tidak boleh  terbalik dan injap hentian mestilah dipasang pada “INLET”.

  2. It is recommended that the unit should be mounted above 1.5m above the floor to bottom of the heater. (Diagram 1)  Pemasangan unit digalakkan mempunyai jarak 1.5m antaralantai dengan bahagian bawah pemanas. (Rajah 1)Rubine FLUSSO Series Water Heater - connection

  3. Mounting position
    Penetapan tapak pemanas
    • Remove screw at the bottom of the heater
    Keluarkan skru dari bawah pemanas
    • Lift the plastic cover upward (Refer Diagram 2)
    Buka penutup plastik pemanas dari bahagian bawah. (Rujuk Rajah 2)
    • Mark mounting position on the wall for all 4 screws  Tandakan posisi semua 4 skru pada dinding
    • Drill the holes with 5.0mm diameter drill bit (Refer Diagram 3)
    Gerudi lubang dengan meggunakan bit gerudi  berdiameter 5.0mm (Rujuk Rajah 3)
    • Install the unit to the wall with plug
    Pasang unit pada dinding bersama plug

  4. Installation of Heater INLET and OUTLET connection. (Diagram 4)
    Pemasangan “INLET” dan “OUTLET” pemanas. (Rajah 4)Rubine FLUSSO Series Water
Heater - bottom

  5. Electrical Connection
    Penyambungan elektrik
    IMPORTANT NOTE !
    NOTA PENTING !
    SWITCH OFF THE MAIN SUPPLY BEFORE ELECTRICAL WORK PADAMKAN SUIS UTAMA SEBELUM MELAKUKAN KERJA-KERJA PENDAWAIAN ELEKTRIK
    a) Insert electrical cable through the rubber grommet as (Diagram 5).
    Masukkan kabel elektrik melalui grommet getah seperti yang ditunjukkan pada (Rajah 5).
    b) Connect the cable to the terminal block and fully tighten as below : Sambungkan kabel ke blok terminal dan ketatkan sepenuhnya seperti berikut:Rubine FLUSSO Series Water Heater - cable
    c) Restore the cover. (Diagram 6)
    Pasangkan penutup pemanas. (Rajah 6)
    To install cover:
    Pemasangan penutup:

  1. Place bottom part into position & fit in nicely.
    Posisikan penutup & ketatkan bahagian bawah dahulu.
  2. Press firmly the top part until “click” to secure the cover.
    Tekan bahagian atas penutup sehingga bunyi “klik”.
  3. Install screw at bottom to lock in position.
    Selepas penutup dipasang dengan ketat, pasangkan skru di bahagian bawah.Rubine FLUSSO Series Water Heater - screw

OPERATION PROCEDURES / TEST RUN OF HEATER

TATACARA OPERASI / PENGUJIAN PEMANAS

  1. Turn on stop valve (anti – clockwise).
    Hidupkan injap hentian (arah lawan jam).

  2. Make sure water flow starts after stop valve had been turned on.
    Pastikan pancuran air bermula selepas injap hentian dihidupkan.

  3. Switch on the main power supply and green “POWER” LED would light up.
    Hidupkan bekalan kuasa utama, dan “POWER” LED hijau akan bernyala.

  4. Turn on temperature control knob and red “HEATER” LED would light up.
    Pusing tombol pengawal suhu dan “HEATER” LED merah akan bernyala.

  5. Test the ELCB by pressing “TEST” button.
    The unit should be tripped. “POWER” LED light and “HEATER” LED light would turn off.
    Uji ELCB dengan menekan butang “TEST”.
    Unit akan diputuskan bekalan kuasa. “POWER” dan “HEATER” LED akan terpadam.

  6. Press reset button to resume power connection.
    Tekan butang “RESET” untuk penyambungan kuasa semula.

  7. The heater is now ready for use.
    Temperature will be increased accordingly as the knob being turned clockwise from “–” to “+”.
    Pemanas kini sedia digunakan.
    Suhu air akan meningkat sewajarnya apabila tombol dipusing mengikut arah jam dari “–” ke “+”.

  8. Switch off the heater and main power supply when not in use.
    Padamkan suis pemanas dan bekalan kuasa apabila tidak menggunakannya.

GENERAL MAINTENANCE

PENYELENGGARAN AMRubine FLUSSO Series Water Heater -
MAINTENANCE

TECHNICAL SPECIFICATIONS

SPESIFIKASI TEKNIKAL

Electrical loading / Muatan elektrik 3.6kW 240V 50/60Hz / 3.8kW 240V 50/60Hz
Other loading / Muatan lain Please refer Electrial loading table

Rujuk jadual pendawaian elektrik
ELCB sensitivity / Sensitiviti ELCB| 15 mA
Operating condition / Keadaan berfungsi| Open system (Open outlet) / Sistem terbuka
Water connection / Sambungan air|    15mm (1/2” BSP)
Degree of protection / Tahap perlindungan| IP25
Min water flow rate / Kadar aliran air min| 2 litre/ min
Min water pressure / Tekanan air min| 20kPa (0.2 bar / 2.9psi )
Max water pressure / Tekanan air max| 4 bar ( 400kPa / 58psi )
Heater dimension (mm) / Ukuran pemanas| 375(H) x 227(W) x 75(D)
Heater nett weight / Berat bersih pemanas| Non pump / Tanpa pam : 1.3kg
Inverter Silent DC Pump / Pam Senyap Inverter DC : 1.7kg

SCHEMATIC WIRING DIAGRAM

RAJAH PENDAWAIAN SKEMATIK
DC PUMP (FS391D)
PAM DC

Rubine FLUSSO Series Water Heater - PUMP

NON -PUMP (FS390N)
TANPA PAMRubine FLUSSO Series Water Heater - TANPA PAM

Our Warranty

| on Internal Parts
pada Bahagian Dalaman
---|---
| on Inverter DC Silent Pump
pada pam Senyap Inverter DC
| on Heating Element
pada Unsur Pemanas
| on Anti-tank Leakage
pada Pencegahan Tangki Bocor

6 mths Warranty Extension

Online Registration

  1. Log on to www.rubine.com.my
  2. Click on ‘Support’, followed by ‘Product Warranty Registration’to proceed. You’re required to sign up as a member.
  3. You’ll receive a notification of warranty registration confirmation via email.
  4.  Please keep your online warranty certificate for reference / future warranty claim.

Pendaftaran Di Laman Web

  1. Layari www.rubine.com.my

  2. Klik pada ‘Support’,diikuti dengan
    ‘Product Warranty Registration’.
    Anda dikehendaki mendaftar sebagai ahli Rubine.

  3. Anda akan menerima e-mel sijil pengesahan dengan data pendaftaran jaminan.

  4. Pastikan anda simpan e-mel sijil pengesahan untuk tuntutan jaminan.

Customer Care

AFTER – SALES SERVICE:
Tel : 03-6279 8899
Email : ftcrm@fiamma.com.my
OPERATION HOURS:
09:00am – 05:00pm
(Monday – Friday, except public holiday)
This specification is subject to change without prior notice,
FIAMMA TRADING SDN. BHD. will not be held responsible for the use of superseded or voided specification.

rubine.com.my
FIAMMA TRADING SDN BHD 230476-P (4 member of Fiamma Holdings Berhad)
2-1, Wisma Fiamma, No.20, Jalan 7A/62A, Bandar Manjalara, 52200 Kuala Lumpur. Tel: 03-6279 8943

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals