Rubine VENTO42 Ceiling Fan User Manual
- June 5, 2024
- Rubine
Table of Contents
Rubine VENTO42 Ceiling Fan
SUPPLIED PARTS
FAN SIZE
| VOLTAGE
| MAX FAN POWER
| MAX SPEED(RPM)| PRODUCT WEIGHT
| CARTON WEIGHT
---|---|---|---|---|---
42″VENTO
|
220-240V/50Hz
|
65W
|
285+/-10%
| 7.0|
8.0
53″VENTO
|
220-240V/50Hz
|
85W
|
240+/-10%
| 7.8|
8.8
instruction
WARNING
TO ENSURE YOUR PERSONAL SAFETY, PLEASE READ THROUGH THE INSTRUCTION MANUAL BEFORE OPERATING THE PRODUCT.
- Do not bend the blade holders during installation, blades balancing or fan cleaning.
- To prevent accidents, power switch must be OFF and electrical wiring must be disconnected before ceiling fan installation, dismantling, maintenance or cleaning.
- Ceiling fan installation and electrical wiring must be done by qualified technician in accordance with all applicable codes and air conditioning engineers (ASH RAE) or the local qualified authorities.
- Be cautious when drilling the wall to avoid damaging electrical wiring and other hidden parts.
- Ceiling fan must be hooked on concrete ceiling. Do not install the ceiling fan on plaster ceiling or any types of drywall ceilings. During ceiling fan installation, all screws must be tightened at all allocated parts.
SAFETY GUIDELINES
- Please do not install the ceiling fan at high humidity areas.
- Distance between fan blades and ground must be at least 2.5 meter and above.
- Do not touch the ceiling fan while it is operating.
- For safety purposes, all electrical connections must conform to the national electrical safety codes and earth wire must be installed correctly (suitable for power supply of 240VAC/50Hz).
- Do not modify the ceiling fan and only use the parts supplied to prevent injuries.
- Do not attempt to repair the fan. Always return the defective fan to our authorized service agent.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- The ceiling fan electrical wiring must be installed with means for disconnection incorporated in the fixed wiring provided and safety cable must be installed according to the steps in this manual.
INSTALLATION PROCEDURES
STEP 1 (Refer Diagram 1)
- Place the rubber wheel on the U-Hook.(Fig.a)
- Lift the motor until the bracket hole of the hanging tube aligns with the rubber wheel hole.
- Tighten the hanging tube to the rubber wheel with the previously loosen bolt, washer, nut and R-pin.
DIAGRAM 1
NOTE
- Remember to lock the pin after tightening the bolt.
- The hook must be installed on the concrete ceiling.
WARNING
Installation without proper procedures as above mentioned might result to fan loosening or falling.
STEP 2 (Safety Cable Installation)
- Remove the safety cable screw from the hanging tube bracket.
- Arrange the safety cable as above image labelled with 2.
- Firmly screw the safety cable onto the hanging tube.
WARNING
Safety cable must be fixed correctly, May cause injury if ceiling fan drops.
STEP 3 (Electrical Wiring Connection)
-
All electrical connections must be in accordance with local and national electrical code standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
-
Before installing the fan turn off the power supply.
-
With the two pieces of lead wires from the screw pack, connect the wire to the fan, then to receiver as below diagram.
-
When the connection is completed, Insert the receiver into the top canopy.
Refer wiring diagram below
STEP 4 (Refer to Diagrams)
- Raise the top canopy and tighten it with the screw attached.
STEP 5 (Blade Installation)
- Insert the blade screws through the flat washeand blade then secure the blade to the motor by tightening the screws.
- Repeat this process to install all the other blades.
STEP 6 (Refer Diagram 7)
- Install the bottom cover to the fan by turning it clockwise.
WARNING
The ceiling fan must be mounted above 2.5m from the floor and 1 m from the wall to the blade.
IMPORTANT
DO NOT CONNECT THIS CEILING FAN REMOTE CONTROL TO A DIMMER SWITCH OR WALL
REGULATOR
The ceiling fan must be hooked to the concrete ceiling. Do not install the
ceiling fan on the plaster ceilings or any types of drywall ceilings. During
ceiling fan installation, all screws must be tightened at all allocated parts.
WRONG INSTALLATION
Do not install ceiling fan under dome, slanted ceiling, too high or low distance as it will cause turbulence air flow and ineffcient low air performance circulation.
- Ceiling Fan must be mounted above 2.5m fromthe floor 1 m from the wall to the blade.
- Avoid fixing inside a dome ceiling.
- Avoid Installing on a deep tray ceiling.
- Avoid Installing on a slanted ceiling.
Our Warranty
Online Registration
- Log on to www.rubine.com.my
- Click on ‘Support’, followed by ‘Product Warranty Registration’ to proceed. You’re required to sign up as a member.
- You’ll receive a notification of warranty registration confirmation via email.
- Please keep your on line warranty certificate for reference/future warranty claim.
Customer Care
AFTER-SALES SERVICE
Tel : 03-6279 8899
Email: ftcrm@fiamma.com.my
This specification is subject to change without prior notice.
FIAMMA TRADING SON. BHD. will not be held responsible for the use of
superseded or voided specifications.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>