FORWODE DB-HBS4222 2 Hitch Mount Bike Rack Instructions

FORWODE DB-HBS4222 2 Hitch Mount Bike Rack

Product Information

Specifications:

• Model: DB-HBS42
• Product Type: 2-Bike Hitch-Tightening System & Flexible Wheel

Product Usage Instructions

Step 1: Installation
Follow the steps below to install the bike carrier:

1. Load two pieces of K into A, then insert B into A and connect with I-J-H fasteners.
2. Insert C into B, and connect the 4 holes with S-T-U locking parts.
3. Insert D1 and D2 into C and secure the connection with the hand screw nuts.

Step 2: Assembly
Continue with the assembly process:

1. Insert G1 and G2 into the bike frame B, position them with keys X, adjust them to a suitable position, and lock them with key X.
2. Insert V and tighten it with a screwdriver at the marked place.

Step 3: Disassembly

To disassemble the bike carrier:
Insert R into the trailer bar, lock it with key W, and pass keys P, and Q through O, M, and N and lock them with a wrench.

Step 4: Tightening the Handle
Make sure to tighten the handle by following these steps:

1. Adjust the fine-tuning preload knob’s initial state to tighten again.
2. Use the handle head with positioning pins and handle grip to secure the handle.

Step 5: Rack Folding
To fold the rack, follow these steps:

1. Press the column slightly to the left and fold it to the right while pressing the pop-up buckle.
2. Press the downed column slightly downward, while pressing the pop-up buckle, and lift the column to the left.

Step 6: Rack Tilt

For tilting the rack:
Pull out the T-handle and put it down for tilting purposes.

Frequently Asked Questions (FAQ):

• Q: How often should I check if the bike carrier fits my vehicle?
  A: It is recommended to check with an authorized FORWODE Bike Rack dealer or distributor before purchase and installation to ensure compatibility.

• Q: What should I do if there are missing or damaged parts?
  A: Contact your authorized FORWODE Bike Rack dealer or distributor for assistance in obtaining replacement parts.

• Q: How should I store this manual for future reference?
  A: Please keep this manual in a safe place for future use and reference.

TOOLS REQUIRED

• Adjustable Wrenches Or 11/16″ & 3/4″ Wrenches
• Phillips Screwdriver

PRODUCT PARTS CATALOG

ITEM NO.

| DESCRIPTION|

QTY.

---|---|---
A| Bottom tube| 1
B| Vertical tube| 1
C| Cross tube assembly| 2
D1| Tyre carrier assembly 1| 2
D2| Tyre carrier assembly 2| 2
G1| Fixed hook 1 assembly| 1
G2| Fixed hook 2 assembly| 1
H| Half-tooth carriage bolt M12| 1
I| Self-locking nut M12| 1
J| Flat spacer12| 1
K| Round with positioning spacer| 2
M| Heavy duty spring pad10| 2
N| Large flat pad$10| 2
O| Hexagonal nut M10| 2
P| U-connector| 1
Q| Fixing plate| 1
R| Trailer lock| 1
S| Half-tooth carriage bolt M1055| 4
T| Flat pad Ф10| 4
U| Self-locking nut M10| 4
V| Phillips bolt M58| 3
W| Trailer lock Key| 2
X| Cross-rail fixed assembly Key| 4

INSTALLATION STEPS

STEP 1:

• Two pieces of K are loaded into the inside of A in advance. (The two cylinders of K are inserted into the two small holes).
• Insert B into the interior of A and then connect in order with I-J-H fasteners.

STEP 2:
Insert C into figure B, the 4 holes on the side are connected with 4 sets of standard parts S-T-U locking respectively（Install the two inner holes first and then the outermost hole).

STEP 3:
Insert D1 and D2 into figure C, respectively, and lock the connection with their own hand screw nuts.

STEP 4:
Insert the G1 and G2 components into the upper square opening of the assembled bike frame B and position the sliding position with the keys X carried on the G1, and G2 components, adjust to a suitable position, and lock G1 G2 with key X.

STEP 5:
Insert the V at the place marked by the arrow above, and tighten it with a screwdriver.

STEP 6:

1. Insert R into the tariler bar.
2. Lock the trailer lock (R) with the key (W) and keep the key
3. Pass P, Q through O, M, and N and lock them with a wrench.

DISASSEMBLY STEPS

• After the handle is locked, P and Q will be locked by M, N and O with a wrench.
• Remove the O-M-N with the handle take off the P-Q and put it away.

TIGHTEN THE HANDLE

• Hold b with your left hand and pull it outward slightly.
• Squeeze (a) tightly with the right hand and tighten.
• Loosen b.
• Pull out d and rotate c to 90°
• Insert d and rotate the handle clockwise until tightened.
• Pull out b, and c with force and rotate back to the initial state to tighten again.
• Disassembly steps refer to tightening steps.

RACK FOLDING STEPS

STEP 1:
Press the column slightly to the left, while pressing the pop-up buckle as shown, and fold the column to the right.

STEP 2:
Press the downed column slightly downward, while pressing the pop-up buckle as shown in the picture, and lift the column to the left.

STEP 3:
Pull out the T-pull, and rotate the frame 90 degrees, then fold and collect the T-pull after releasing it. Rotate it 90 degrees, and then snap the square into the sheet metal slot for positioning.

STEP 4:
Pull up the handle to fold up when not carrying bikes.

RACK TILT STEPS

Pull out the T-handle and put it down.

GENERAL CONSIDERATIONS

1. Every month new designs and bodies are introduced to the market.
2. The FORWODE bike carrier design team strives to make most products universal to the cars on the market. A single bike carrier can’t fit all models of cars on the market.
3. Before you purchase a rack, please check if the rack fits your vehicle with an authorized FORWODE Bike Rack dealer or distributor.
4. Before installation, please read the instructions and then follow the attached instructions.
5. Before installation, please make sure all parts are present and in working condition. For any missing or damaged parts, please contact your authorized FOR- WODE Bike Rack dealer or distributor.
6. Please always keep this manual for future reference.

WARNING WHEN INSTALLING THE FRAME

1. When the vehicle is equipped with an electric rear fender, the power must be turned off when installing the rear carrier. If this option is not available, do not use the rear bike carrier.
2. Clean the receiver connector thoroughly before installing it.
3. When the vehicle is equipped with a spoiler or similar item, it is necessary to change the mounting method of the bike carrier. If this happens, please contact an authorized FORWODE bike carrier verifying dealer or distributor.
4. When using the bike carrier, please observe local traffic laws.
5. When not in use, please remove the rack before washing your bike.

WARNING WHEN MOUNTING THE BICYCLE

1. When you ride your bicycle, make sure that it does not touch the vehicle, especially the pedals. Using protective foam pads may be helpful.
2. Remove all loose items before mounting the bike. For example, water bottles.
3. Bicycle tyres must be kept away from vehicle exhaust fumes.
4. Always observe the weight of each bicycle (60 lbs. maximum per bicycle) and the capacity of the bicycle, according to the manufacturer’s recommendations.
5. Bike mounts/bikes are mounted with different road behaviour for vehicles. Use extreme caution when driving in high winds, sharp turns and on rough roads. Drive slowly over speed bumps (10 km/h)
6. Vehicles with bike racks installed have extra width and length. Also, make sure that the bicycle is mounted in the middle to avoid excessive protrusion.
7. When the vehicle is equipped with a bicycle rack, check the installation of the rack and the installation of the bicycle every 100 km while driving. It is the driver’s responsibility to ensure the safety of passengers and others!

WARRANTY AND LIABILITY

1. FORWODE does not bother to assume any liability for any damages (to the vehicle, damage caused by incorrect installation and use of this product or its accessories, goods and/or persons in connection with the purchase, use or handling of this product).
2. If you have further questions about our limited lifetime warranty or need any support, you can start a conversation with us at [email protected].

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>