Rubine RCH-ASPIRA-90SS Cooker Hood User Manual
- June 3, 2024
- Rubine
Table of Contents
- Rubine RCH-ASPIRA-90SS Cooker Hood
- SPECIFICATIONS
- PRODUCT DIMENSION
- OPERATING INSTRUCTION
- INSTALLATION REQUIREMENT
- INSTALLATION PROCEDURES
- MAINTENANCE
- IMPORTANT SAFETY INSTRUCTIONS
- TROUBLESHOOTING
- WARRANTY CARD
- Customer Care
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Rubine RCH-ASPIRA-90SS Cooker Hood
Dear Valued Customer,
Congratulations and thanks for trusting RUBINE as part of your kitchen
appliances. This product is subject to strict Quality Control during the
entire process of manufacturing and assembly. It is meticulously tested to
ensure lowest defect possible when it is used in your kitchen. Do not remove
the product from its protective packaging until it is installed.
Please read and understand the instruction carefully before proceeding to
install and use the appliances. The information contained in this manual is
essential for proper operation of the appliance and, more importantly, for
your safety. Being socially and environmentally responsible, the packaging of
the appliance has been manufactured using only materials which are strictly
necessary to guarantee efficient protection during transport.
To contribute to the environment, you can dispose the packaging into
appropriate recycling bin. You can contact your local authority to find out
the nearest recycling centre for your old product. Do not pour used oil down
the sink; instead, collect in sealed container and take it to an appropriate
oil disposal centre to avoid ground water contamination.
IMPORTANT: The quality of the final product is recorded according to the
serial number. In the unlikely event that the appliance should be damaged or
not meeting your expectations in terms of quality, please inform us as soon as
possible. For the warranty to be valid, the appliance must not been tampered
with, or used inappropriately.
SPECIFICATIONS
- Model Name : RCH-ASPIRA-90SS
- Total Power : 224W
- Motor Power : 220W
- LED Lamp : 1x4W
- Voltage : 220V – 240V
- Frequency : 50Hz
PRODUCT DIMENSION
OPERATING INSTRUCTION
This is a highly sensitive touch control. Gently press the control to operate.
-
Power/Delay button:
Press the “Power/Delay” button to turn on the range hood, the “Power/ Delay” button flashes, and the range hood will power up. Press the “Power/Delay” button to turn off the range hood, the “Power/ Delay” button flashes, and the range hood will enter delay state for 1 minute and will power off the range hood after the delay is over. This is to clear the air after cooking completion.
In the delay state, press the “Power / Delay” button again to turn immediately turn off the range hood. -
Low Speed button:
In the power-on state, press the “Low Speed” button once, and the range hood will run in low gear. -
Fast Speed button:
In the power-on state, press the “Fast Speed” button once and the range hood will run in fast speed. -
Boost button:
In the power-on state, press the “Boost” button once, and the hood will run in the boosted mode. After running for 3 minutes, it will automatically change to the fast speed. This is to provide better suction during deep frying. -
Light button:
Press the light button to turn on the light, and press the light button again to turn off the light. -
Hand Sensor zone:
When the range hood is in off state, wave your hand slowly in front of the hand sensor zone, the range hood will power up in fast speed, wave your hand again to turn off the range hood.
INSTALLATION REQUIREMENT
- To have the optimum suction performance, do not install cooker hood near to door and windows. External wind will reduce the efficiency of the range hood. (Fig. 1)
- Install range hood directly above the hob. The optimum distance between the cooker good and hob is 300mm to 350mm. (Fig. 2)
- For best suction performance, minimize the length of the ducting hose, minimize the number of angles and do not over-bend the pipe more than 90 degree. (Fig. 3)
- Ensure the cooker hood is vertically straight after installation. (Fig. 4)
- The air outlet MUST NOT be connected to chimney flues or combustion gas ducts. DO NOT connect the air outlet to ventilation duct which fuel-burning appliances are installed
INSTALLATION PROCEDURES
SAFETY WARNING
Some parts of the range hood may have very sharp edges. Please wear protective
gloves if you need to remove any parts during installation, cleaning or
servicing. Make sure the wall able to hold / withstand the weight of cooker
hood. It should not have contact with any cable inside / outside to avoid
electric shock. Do refer your hob user manual for any special requirement.
-
Step 1:
Install the cooker hood according to the recommended distance between 300mm to 350mm above the hob. -
Step 2:
Drill holes on the proper positions of the wall, insert the provided wall plug into the holes. Tighten the screw into the holes and ensure it is tightly screwed. Hang the cooker hood on the bracket and ensure it is level and stable. -
Step 3:
Fix the ducting hose into the air outlet of the inner duct. It has to be tightly connected. -
Step 4:
- a.) Adjust the desired height of the inner duct and draw 2 markings against the bracket holes.
- b.) Put the inner duct aside and drill the holes, then insert the wall plug into the holes.
- c.) Place the inner duct on the wall and tightened it with screw and ensure bracket is aligned.
-
Step 5:
Extend the air outlet ducting hose outdoor.
MAINTENANCE
To ensure efficiency & product lifespan, clean the range hood surface & motor
regularly. Before any cleaning & maintenance, make sure the range hood is
switched-off and unplugged. Wear glove during maintenance to avoid injuries or
scratching the range hood.
Use mild soap or detergent solution to clean the surface once a week depending
on the usage
Motor fans and other internal part should be cleaned once every 6 months,
depending on usage. This should be conducted by Qualified personnel only. Do
not clean the motor with water or others liquid.
Oil Filter & Motor Turbine Dismantling Method
Please make sure the components are place gently after dismantle to avoid any
dented to the component.
- Remove out the oil filter (A). Then remove the three screws from the lower panel (B). Then Push up and take out the glass panel (C).
- Remove the four screws on the upper panel and remove the baffle filter (A).
- Unscrew and remove the motor turbine rime cover (A).
- Unscrew the motor turbine nut (A). Then, take out the motor turbine (B).
For Charcoal Filter Installation
- Remove out the oil filter (A). Then remove the three screws from the lower panel (B). Then Push up and take out the glass panel (C).
- Remove the four screws on the upper panel and remove the baffle filter (A). Then, install the charcoal filter to the location show by Arrow (B).
Installation of Extended Ducting Hose Cover
- Install the range hood, use a measuring tape to measure the distance from the ceiling of the kitchen to the top of the range hood ducting hose cover to determine the height of the extended decorative cover.
- Use a measuring tape to measure the distance from the top of the ducting hose extension cover to the hole of the ducting hose extension cover, and use this distance to determine the position of the ducting hose extension cover from the ceiling of the kitchen.
- Fix the ducting hose extension cover on the wall with screws, then pull out the extended ducting hose cover part and fix it on the fixing bar on the left and right sides. (Pictured)
Installation of Ducting Hose Cover
Cleaning of the component
Use mild soap or detergent solution to clean the component. Do not use organic
solvents. Soak it for 30 minutes before wash. Ensure to avoid any damages to
the component. After clean it with mild soap or detergent solution, wash it
again with water & wipe it with dry cloth. Only use dry cloth to clean
electrical components, do not use water or any soap on it.
Dismantle & Replacement of LED Light
Caution: Hot surface! To dismantle and replace the LED light, ensure that the
range hood is switched-off and unplugged.
- Use a flat head screwdriver to pull out the LED light subassembly
- Pull out from the connection with internal wires.
- Replace with new LED light
- Connect the LED light subassembly with internal wires and push the lamp into the hood.
IMPORTANT SAFETY INSTRUCTIONS
TROUBLESHOOTING
Malfunctions | Causes | Action |
---|
LED light malfunction while motor is operating
| LED light is not install| ****
Contact service centre & request technician to:
– install the LED light
– replace new LED light
LED light is not install correctly
LED light broken
Both motor & LED light are malfunction
| Plug & socket might be damaged or might not be connected correctly| ****
Repair / change new plug or socket
Display board might be damaged or might not connect correctly
LED light is on but motor is not operating
| Thermal protector damaged| Change motor
Capacitor damaged| Change capacitor
Motor damaged| Change motor
Hood is shaking| Blower not installed correctly| Adjust the blower
Noisier| Ducting cover not installed correctly| Check & tighten ducting cover
Weak Suction
| Hood installed too far from hob| Adjust the distance
Air / wind convection| slightly open door/ window
Hose installed too long, connection point did not seal correctly, too many
bending or deform| ****
Check & install the hose correctly
Butterfly vane is close| Remove the tape, adjust hose to ensure no blockage
Hob install too far from cooker hood| Adjust hob position
Low power supply to hood| Check the flow of power supply 200-240 V
WARRANTY CARD
WARRANTY CONDITIONS
Subject to following Term & Conditions, this equipment is guaranteed against
defective material & manufacturing defects by Fiamma Trading Sdn Bhd for a
period of twelve (12) months from the date of original purchase. Fiamma
Trading Sdn Bhd reserves the right to change these terms & conditions without
prior notice.
Terms & Conditions:
-
This warranty is valid & provided that warranty card is completed with authorized dealer’s stamp from the date of original purchase and in the territory of Malaysia only.
-
This warranty covers repair or, at the option of Fiamma Trading Sdn Bhd, replacement of any parts proven to be defective due to defective workmanship or material provided that the product was purchased from an authorized dealer of Fiamma Trading Sdn Bhd.
-
This warranty does not cover the damage resulting from:
- Any unauthorized disassembly, service repair, alteration or modification being carried out.
- Abnormal voltage or the use of generator and/or used not in accordance with the Operating Manual/ Userl Manual.
- Misuse, abuse, negligence or accident howsoever caused.
- Normal wear or tear.
- Rough handling & transportation.
- Commercial public use e.g. hotel, laundry, college, university, etc.
-
This warranty does not cover the following accessories:
- Burner Caps/Supports
- Cast Iron Grib (c) Knabs
- Body Wark (e) Light Bulb
- Charcoal Filter
- Cover
- Glass Cover/
- Screen
- Trays/Shelves
- Hose
-
This warranty is considered null &void in the events if:
- Any item contained in this warranty card has been tempered with or altered in any way without the prior written consent of Fiamma Trading Sdn Bhd. Request for warranty services within the warranty period must be accompanied with this warranty card & proof of original purchase.
- Any time during the warranty period, any part modified, dismantled, repaired or handled in any way whatsoever by any person / persons not authorized by us
- The serial number of the product has been defaced or removed.
parts of this equipment is / are removed, altered, tempered with, adjusted,
-
Waanty for WINE CHILLER compressor is (5) five years, gas refill and labor charges are excluded.
-
In the event of defects covered by this wamanty arising during the waranty period, the purchaser shall be fully responsible for the due delivery to our dedicated service centre of the equipment (expect for the refrigerator, washing machine, ovens, cooker hood, gas cooker, dishwasher, dryer, built-in hob, freezer, water heater) for any work which shall need to be done pursuant to this warranty & subsequent collection thereof of the equipment after the said work has been done.
-
This waranty is in lieu of any, and all other warranties expressed or implied warranty of merchantability or fitness for a particular purpose. Fiamma Trading Sdn Bhd assumes no liability for the breach of the warranty beyond correcting the breath in the manner described above. In no event shall Fiamma Trading Sdn Bhd be liable for cornsequential losses or damages, including loss of use or loss of profits resulting from the product.
Customer Care
rubine.com.my
FIAMMA TRADING SDN BHD 330176-P (A member ol Fiamma Holaings Bormad) 9-2,
Wisma Fiamma, No.20, Jalan 7A/62A, Bandar Manjalara, 52200 Kuala Lumpur. Tel:
03-6279 8943
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>