WILIT G1 LED Table Lamp Instruction Manual
- June 12, 2024
- WILIT
Table of Contents
G1
Instruction Manual for LED Table Lamp
Product Introduction
Please read carefully before using and keep it properly.
Operation Instructions
- Power connection
Plug in the power adapter,the RGB lamp flashes, and the LED lamp lights up to show the screen pulling effect.
Notice:
- Please use the original power supply, do not use the cable extension or splitter, otherwise the product may work abnormal
- Do not use an adapter which isnt match with output 12V
- lithe lights flickered or noisy, please timely check the power supply
- Do not connect the adapter metal point with other meta Is.or permanent damage to yout product or other dangerous may resultor
- The orginal adapter is for this product only and do not support for other use
Light Control
LED Lamp adjustment: Press the ” ” key to turn on/off the lamp,long press the”
” key to switch temperature color: coldlight, warm light, cold and warm light
cycle adjustment. Short press the” ” key to increase brightness,short press
the” ” key to decrease the brightness. When the LED light and colored light
turn on at the same time, press the” ” key to turn off the LED light and
colored light together. Color lamp adjustment
Short press” “key to open the color lamp.The color light mode is colorful
rhythm-monochromatic rhythm-colorful rhythm with sound grab-color flowing –
color progression ,the lights can be adjusted circularly. Long press” ” the
key to turn off the color lamp.
Charging function
Wireless
charger: Electronic products that support 01 wireless charging function can
be charged by placing them in the middle of Cll.
USB: Supports 5V/2.1A power devices
Illumination Angle Adjustment
Warnning:
Please do not over-adjusting the joint activity parts to avoid any damage to
the lamp. 
Note: The product,
accessories, user interface and other illustrations in the manual are
schematic diagrams for reference only.Due to product upgrading,physical
product may be slightly different from the schematic diagram.Please refer to
the object.
Specification
Model: G1
Maximum Power: 30W±10%
LED Lamp power : 4.2W
Lumens: 400-500LM
USB output: 5V/2.1A
Wireless charger power: 5W
Color rendering index: RA> 80
Lighting size: 404127.8186mm
Color temperature range: 5000±283K;2800K±283K;4000K±283K
Cautions
- Please wipe it by soft cotton fabric for surface cleaning, and do not use any corrosive solvents.
- The light source is irreplaceable. Please stop use when actually wear out
- If a failover occurs, please do not disassemble by yourself to avoid any damage on the product.You can contact the manufacture for maintenance.
Product performance fault table
| Model | Performance failure |
|---|---|
| G1 | 1. The light doesn’t work |
2. Lamp flickering
3. Unable to turn on the light
4. Slow wireless charging
5. Shell is damaged due to structural or material factors
- You’re advised to keep the packing boxes for at least 30 days after receiving, since the packing boxes are used to ensure the safety of transportation;
- This product is only sold in China mainland (excluding Hong Kong, Macao and Taiwan), so the warranty is for China mainland only(excluding Hong Kong, Macao and Taiwan.
Warranty card
cut hete
Customer name: ……………………………………..(Mr/Ms)
Tel: …………………………………………..
Address serial: ………………………………….
Number: ……………………………………..
Model Purchasing: ……………………………….
Date: ……………………………………….
Purchasing store: ……………………………..
Store address: …………………………………..
Invoice number: ………………………………..
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>