Rubine ITALIA RCH-MARIA-SS Home and Kitchen Appliances User Manual
- June 12, 2024
- Rubine ITALIA
Table of Contents
RCH-MARIA-SS Home and Kitchen Appliances
Product Information
Thank you for purchasing our product. Please read this user
manual carefully for important information and instructions on how
to use the product.
Specifications
- Product Dimension: 370 x 307 x 260 mm
Troubleshootings
CAUTION: Disconnect the power supply before servicing.
Status: Damaged power supply
Cause & Method of Repairing: If the power
supply is damaged, please call a technician to repair it.
Tool: +type screwdriver, sharp pincers
The lamp works but the motor does not run:
-
Take off the filter and check the connection between the air
inlet and wind chamber to ensure it is properly sealed. -
Check the connection between the air exhaust pipe and wind
chamber for any oil leakage. If there is leakage, fill it up with
varnish or thinner. -
If the motor stops running and has a bad odor after a moment of
operation, the motor wires may be burnt out. Please replace the
motor. -
If the starting wire (yellow) is disengaged from the condenser,
it needs to be rewired. -
If the condenser is damaged, please replace it with a new
one.
Machine vibration:
- If the motor is not firmly screwed, tighten the screw.
- If the vane is damaged or unbalanced, replace it with a new
one.
Weak suction:
-
The distance between the cooker hood and hob may be too far.
Adjust the distance accordingly. -
If there are many windows or doors causing strong wind
convection, consider closing them or adjusting the position of the
cooker hood.
Tilting hood:
-
Adjust the height of the model where it is hung on the
ceiling. -
If the model tilts forward, lock the wall with wood screws
again or check if the screws fixing the model are loose.
Lamp does not light up:
Take off the screw from the lamp shade, replace it with a new
light bulb, and fix the lamp shade back.
Product Parts Diagram
- Hook
- Shutter Cable Hook
- Blower Box Assembly
- Motor House
- Heat-Autoclear Bottom Cover Assembly
- LED Lamp
- Filter
- Oil Cup
- Inner Telescopic Duct
- Outer Telescopic Duct
- Electrical Box
- Capacitor PCB
- PCB Fix Board
- Cover
- Charcoal Filter
- Top Glass Panel
- Switch Assembly
- Glass Panel
Disposal Instructions
Please note that this product is marked with the symbol
indicating that it should be separately collected and treated
according to the Waste of Electrical and Electronic Equipment
(WEEE) directive. If you need to dispose of this product in the
future, please do not dispose of it with household waste. Instead,
send it to a WEEE collection point.
Safety Precautions
-
Dress the protective glove before you start to clean the hood.
Remove the components gently during the clearance. -
Never wash the control switch with water or any other liquid as
it may cause electrical problems. -
Cleaning the motor fan should be undertaken by a qualified
person to avoid any distortion of the fan. -
Never pull the plug out of the power supply with wet hands to
avoid the possibility of electric shock. -
Disconnect the cooker hood from the power supply if it will not
be used for a long time.
03-6286-9000
RCH-MARIA-SS
Dear valued customer, Thanks for your purchase of our product. PLEASE READ &
KEEP THIS USER MANUAL
CONTENTS
SPECIFICATIONS …………………………………………………………………… 1 PRODUCT DIMENSION
…………………………………………………………….. 1 PRODUCT PART DIAGRAM ………………………………………………………. 2
INSTALLATION REQUIREMENT …………………………………………………… 3 INSTALLATION PROCEDURES
………………………………………………… 4-5 CHARCOAL FILTER INSTALLATION & REPLACEMENT ……………………
5-6 OPERATING INSTRUCTIONS …………………………………………………….. 6 MAINTENANCE
…………………………………………………………………….. 7 TO REPLACE LED LAMP ……. ……………………………………………………. 7
IMPORTANT SAFETY INSTRUCTIONS ……………………………………….. 8-9 TROUBLESHOOTINGS
…………………………………………………………… 10 WARRANTY CARD ………………………………………………………………… 11
Please note that this product is marked with this symbol: According to Waste
of Electrical and Electronic Equipment (WEEE) directive, WEEE should
separately collect and treat. If in future you need to dispose this product,
PLEASE DO NOT disposes it with household waste. Please send it to WEEE
collection point.
11
SPECIFICATIONS
Model Name:RCH-MARIA-SS Total Power:204W Motor Power:200W LED Lamp:2×2W
Voltage:220-240V Frequency:50Hz Filter:Pyramid Filter Control Panel: Sensor
Touch Control
PRODUCT DIMENSION
370
307
260
567-967 475 565
500
896
TROUBLESHOOTINGS
CAUTION:Disconnect the power supply before servicing.
STATUS
Damaged of power supply
CAUSE & METHOD OF REPAIRING
If the power supply is damaged, please call technician to repair.
TOOL
“+”type screwdriver sharp pincers
The lamp works but the motor does not run
a)Take off the filter and check the connection
between air inlet and wind chamber whether it is
sealed or not.
b)Check the connection between air exhaust pipe
and wind chamber whether there is leakage of oil or
not. If YES, please fill it up with the varnish or thinner. c)If the motor stops running and has a bad odor after a moment of operation, the motor wires may be
“+”type screwdriver
burnout. Please replace motor
d)If the starting wire (yellow) is disengaged from the
condenser, it needs to be rewired
e)If the condenser is damaged, please replace with
a new one.
Machine vibration
a)If the motor were not firmly screwed, tighten the screw up. b)If the vane is damaged or unbalanced, replace with a new one.
“+”type screwdriver
Weak suction
a)The distance is too far between the cooker hood and hob. b)There are many windows (doors) causes strong wind convection. c)If due to the position of cooker hood install upon the window, you may put a three-ply board on the back of the cooker hood to cover the spaces.
“+”type screwdriver”+”
Tilting hood
a)Adjust the height of the model where it is hung on the ceiling. b)If the model tilt forward, lock the wall with wood screw again (the screw peep out around 0.5~1 cm from the wall), or check the screw that fixing the model are loose or not.
“+”type screwdriver
Lamp does not light-up
Take the screw off from the lamp shade and replace “+”type with a new light bulb, then fix the lamp shade back. screwdriver
10
Glove
Dress the protective glove before you start to clean the hood.Remove the
components gently during
carrying out the clearance.
Never wash the control switch with water or other kind of liquid for
the liquid might cause electrical problem to
the hood. To clean the motor fan should be undertaken by a qualified
person,pay top attention to avoid any distortion of the fan during carrying
out the clearance. Never pull the plug out of the power supply by wet hand to
avoid the possibility of electric
shock. Disconnect the cooker hood from the power supply if this appliancewill
not be used for a long time.
9
PRODUCT PARTS DIAGRAM
Hook
Shutter Cable Hook
Blower Box Assembly
Motor House
Heat-Autoclear Bottom Cover Assembly LED Lamp Filter Oil Cup
Inner telescopic duct
Outer telescopic duct
Electrical Box Capacitor PCB PCB fix board
Cover
Charcoal Filter Top Glass panel
Switch Assembly Glass Panel
2
INSTALLATION REQUIREMENT
1.Do not install the cooker hood where there are many doors or windows in
order to avoid affecting the exhaust efficiency of the hood caused by air
convection. (refer Fig. 1)
2.Install the cooker hood right above the hob. The recommended distance
between the hob and the lower edge of the cooker hood is minimum 650 mm and
maximum 700mm. (Fig. 2)
3.In order to get the optimum performance, do not elongate the exhaust pipe
too long, avoid over-bending of exhaust. Ensure the connection is airproof.
(Fig. 3)
4.After hanging the unit on the wall, ensure the hood’ level is vertically
straight. (Fig. 4)
5.The air outlet must not be connected to chimney flues or combustion gas
ducts. The air outlet must be under no circumstances, be connected to
ventilation ducts in which fuel-burning appliances are installed.
Fig.1
Fig.2
Fig.3
650~700mm
LEVEL VERTICAL
LEAN LEAN 3
Fig.4
Manual
IMPORTANT SAFETY INSTRUCTIONS
Do not connect the air outlet to chimney flues or
combustion gas ducts.
Do not leave naked flames under the hood.
In case of any damage to power cable, replace the broken cable with a new one
by qualified
person. Do clean the hood correctly in accordance with instruction stated or
it might cause the possibility
of fire accident. To replace the bulb should be undertaken by a qualified
electrician or a competent person.Always use the halogen bulb not more than
10W or LED lamp no
more than 2W. 8
MAINTENANCE
CAUTION: NEVER PUT YOUR HAND INTO THE AREA WHILE THE FAN IS OPERATING. TO GAIN
OPTIMAL LEVEL OF HOOD PEFORMANCE, CLEAN THE COOKER HOOD SURFACE, FAN AND OIL
FILTER REGULARLY. 1.Use only mild soap or detergent solutions to clean the
cooker hood surface. 2.Clean the filter depending to usage or at least once a
week. Press the
buckle of the filter slightly, take off the filter and put it into warm soapy
water using mild detergent, lightly brush the filter with soft brush. Place
the filter back after it is dry. 3.Clean the fan motor and others internal
parts twice a year or depending to usage by QUALIFIED PERSONNEL. 4.DO NOT
clean the motor with water or other liquid.
TO REPLACE LED LAMP
CAUTION: The lamp may be hot! Wait until unit is cool. If the lamps
malfunction, please replace it with a new lamp. Make sure all the control is
switches off and the cooker hood is unplugged! Please follow below
instructions: 1.Takeoutthefilters,andcutoffthewireconnectionofthelamp. 2.Press
the spring according to the arrow direction,then you can take off
the lamp unit. 3.You can replace a new LED lamp unit no more than rating!
4.Then put the lamp unit to the hood in reverse direction.Connect the wire
of the lamp. 5.Fit on the filters.
7
INSTALLATION PROCEDURES please carefully read the following diagram before installation, and install in accordance with the steps to ensure the smooth installation of the product.
30mm
Exhaust pipe(longest tensile 1500mm)
Hole size 195mm
Hanging wall case
320 260
10mm
415
Hanging wall case
520
650-700
Cabinet
Expanding Tube 5×50
Metal Screw
Hook Expanding Tube
5×50 Metal Screw
Installing Bracket
320mm
260mm
Exhaust pipe Air Outlet Assembly
Fixing Screw
Limiting Screw
9mm 29mm
800-850
Cabinet
Unit: mm
According to the dimension of installing bracket, on the walls in the corresponding position to accurately determine the position of an installing hole, use a 10 impact drilling out the mounting holes, and firmly buried expanding tube, then use the M5x50 wood screws fastening the installing bracket tothe wall.
Put the exhaust pipe on the air outlet (which side marked with 163mm) , put the Fixing screw infeed to make the exhaust pipe fixed.
Pick the cooker hood up,the hanging hole at the back of the box assembly is
aligned with the hanger on the installing braket, and the limiting screw in
the accessory bag is fixed on the hole of the installing bracket to prevent
the accidental fall of the hood.
4
M4 Screw
Hook
Inner duct cover
Outer duct cover
Pull the inner duct cover to a suitable height and secure the inner duct cover from the side to the installation bracket with the cross screwdriver.
functions effectively, regular maintenance is necessary as clogged filters
restrict airflowand may cause the motor to overheat.
3. Removing and inserting the charcoal filter: Take the baffle filter apart,
hold onto the air intakes and turn slightly. Once the charcoal filter turns
out of the screw, remove directly.
OPERATING INSTRUCTIONS
If you need connect the common flue, please do not put the exhaust pipe too deeply,so as to not affect the effect.
30mm
If you connect the exhaust pipe to outdoor,please push it out of the wall at least 30mm, the air outlet should be slightly adown,to avoid rain water intrustion.
Installation confirmation: after installation, check the hood whether it is solid,turn the power on and test it, examin the function whether it is normal and whether there is abnormal vibration of the body,after confirmation,can be used.
CHARCOAL FILTER INSTALLATION & REPLACEMENT
1. The charcoal filters should be replaced when it is noticeably dirty or discolored, usually after 6 to 12 months depending on the
Charcoal Filter
Mounting Screw Mounting Slot
conditions of use.
2. These filters are not washable and cannot be
restored. To ensure that this appliance
5
ON/OFF H² MELTZ SPEED SETTING LIGHT
For the first time, after power on, the buzzer have “dingdong” sound, the
power supply is switched on, in power on state, display is not displayed.
Note: All of the indicator show white light.
Power key: When in off state, press once to enter into standby mode, display
show “0”, press again to enter into off state. When in operating mode, press
once to enter into delay mode, the default delay time is one minute, after the
countdown, the blower/fan and the LED lamp will be turn off automatically.When
in countdown mode, press the on/off key to exit delay timer mode, and turn off
the blower/fan.
H² Meltz key: When in standby mode, press this key to start the H² Meltz
function, the function began to work(the heating module working 10 minutes,
the blower/fan working 1 min),after the completion of oil melting, enter into
off state automatically. When the auto-clean in working state, press “H²
Meltz” key or “on/off” key to turn it off. Note: enter into the auto-cleaning
function, all of the other functions are locked, operation is invalid, exclude
the lighting function could be operated.
Speed key: In standby mode,press the speed key, the blower run in medium
speed, and display show “2”, press it repeatedly, the speed could be cycled
selection between “2-3-1”.
Light key: Press to select the light on/off.
6
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>