Rubine RCH-NEORA-90BL Cooker Hood User Manual

Rubine RCH-NEORA-90BL Cooker Hood

Dear valued customer,
Thanks for your purchase of our product. PLEASE READ & KEEP THIS USER MANUAL

Please note that this product is marked with this symbol:
According to Waste of Electrical and Electronic Equipment (WEEE) directive, WEEE should separately collect and treat. If in future you need to dispose this product, PLEASE DO NOT disposes it with household waste. Please send it to WEEE collection point.

SPECIFICATIONS

• Model Name: RCH-NEORA-90BL Total Power:242W
• Motor Power: 238W
• LED Lamp: 2×2W
• Voltage: 220-240V
• Frequency: 50Hz
• Control Panel: Sensor Touch Control

PRODUCT DIMENSION

PRODUCT PARTS DIAGRAM

INSTALLATION REQUIREMENT

1. Do not install the cooker hood where there are many doors or windows in order to avoid affecting the exhaust efficiency of the hood caused by air convection. (refer Fig. 1)
2. Install the cooker hood right above the hob. The recommended distance between the hob and the lower edge of the cooker hood is minimum 300 mm and maximum 350mm. (Fig. 2)
3. In order to get the optimum performance, do not elongate the exhaust pipe too long, avoid over-bending of exhaust. Ensure the connection is airproof. (Fig. 3)
4. After hanging the unit on the wall, ensure the hood’ level is vertically straight. (Fig. 4)
5. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must be under no circumstances, be connected to ventilation ducts in which fuel-burning appliances are installed.

INSTALLATION PROCEDURES

please carefully read the following diagram before installation, and install in accordance with the steps to ensure the smooth installation of the product.

• According to the dimension of installing bracket, on the walls in the corresponding position to accurately determine the position of an installing hole, use a Φ10 impact drilling out the mounting holes, and firmly buried expanding tube, then use the M5x50 wood screws fastening the installing bracket tothe wall.

• Remove the pan head screw with the air outlet cross slot at the top of the box, and then fix the hole position of the outlet component, and fasten the outlet component on the box with the removed screw respectively.

• Embed the clasp on the outlet joint with a step at one end, then align the clasp on the outlet and press the clasp to the bottom.

• Pick the cooker hood up,the hanging hole at the back of the box assembly is aligned with the hanger on the installing braket, and the limiting screw in the accessory bag is fixed on the hole of the installing bracket to prevent the accidental fall of the hood.

• Matching the hook to the holes of the inne duct cover and fix it well with M4 screws.

• Insert the inner duct cover into the outer duct cover.

• Fasten the perforated end of the Outer telescopic duct to the screw on the top plate and gently push the Outer telescopic duct back, then connect the Outer telescopic duct with the hood and fix it.
• If you need connect the common flue, please do not put the exhaust pipe too deeply,so as to not affect the effect.
• If you connect the exhaust pipe to outdoor,please push it out of the wall at least 30mm, the air outlet should be slightly adown,to avoid rain water intrustion.

Installation confirmation: after installation, check the hood whether it is solid,turn the power on and test it, examin the function whether it is normal and whether there is abnormal vibration of the body,after confirmation,can be used.

CHARCOAL FILTER INSTALLATION & REPLACEMENT

1. The charcoal filters should be replaced when it is noticeably dirty or discolored, usually after 6 to 12 months depending on the conditions of use.
2. These filters are not washable and cannot be restored. To ensure that this appliance functions effectively, regular maintenance is necessary as clogged filters restrict airflow and may cause the motor to overheat.
3.  Removing and inserting the charcoal filter:
   Take the baffle filter apart, hold onto the air intakes and turn slightly. Once the charcoal filter turns out of the screw, remove directly.

OPERATING INSTRUCTIONS

• When it is Power-Up state, press this button into standby mode and the indicator lamp flashes; At the motor working state, press this button and the indicator lamp flashes, then the range hood continue to operate 3 min. After the delay, power will be cut off automatically; At the delay state, press this button and the power will be cut off.
• Touch to select low speed.
• Touch to select high speed.
• When in standby mode, press this key to start the H² Meltz function, the function began to work(the heating module working 10 minutes, the blower/fan working 1 min), after the completion of oil melting, enter into off state automatically. When the auto-clean in working state, press “H² Meltz” key or “on/off” key to turn it off.
  When working 15 hours, there will be a reminder, the key will shine 10 seconds. That’s a circulation.
  Note: enter into the auto-cleaning function, all of the other functions are locked, operation is invalid, exclude the lighting function could be operated.
  Touch to turn on/off the light.

MAINTENANCE

CAUTION: NEVER PUT YOUR HAND INTO THE AREA WHILE THE FAN IS OPERATING. TO GAIN OPTIMAL LEVEL OF HOOD PEFORMANCE, CLEAN THE COOKER HOOD SURFACE, FAN AND OIL FILTER REGULARLY.

1. Use only mild soap or detergent solutions to clean the cooker hood surface.
2. Clean the filter depending to usage or at least once a week. Press the buckle of the filter slightly, take off the filter and put it into warm soapy water using mild detergent, lightly brush the filter with soft brush. Place the filter back after it is dry.
3. Clean the fan motor and others internal parts twice a year or depending to usage by QUALIFIED PERSONNEL.
4. DO NOT clean the motor with water or other liquid

TO REPLACE LED LAMP

CAUTION: The lamp may be hot! Wait until unit is cool. If the lamps malfunction, please replace it with a new lamp. Make sure all the control is switches off and the cooker hood is unplugged!
Please follow below instructions:

1. Take out the filters,and cut off the wire connection of the lamp.
2. Press the spring according to the arrow direction,then you can take off the lamp unit.
3. You can replace a new LED lamp unit no more than rating!
4. Then put the lamp unit to the hood in reverse direction.Connect the wire of the lamp.
5. Fit on the filters.

IMPORTANT SAFETY INSTRUCTIONS:

TROUBLESHOOTING

CAUTION: Disconnect the power supply before servicing.

The lamp works but the motor does not run

|

a)  Take off the filter and check the connection between air inlet and wind chamber whether it is sealed or not.

b)  Check the connection between air exhaust pipe and wind chamber whether there is leakage of oil or not. If YES, please fill it up with the varnish or thinner. c)If the motor stops running and has a bad odor after a moment of operation, the motor wires may be burnout. Please replace motor

d)  If the starting wire (yellow) is disengaged from the condenser, it needs to be rewired

e)  If the condenser is damaged, please replace with a new one.

|

“+” type screwdriver

Machine vibration

|

a)  If the motor were not firmly screwed, tighten the screw up.

b)  If the vane is damaged or unbalanced, replace with a new one.

|

“+” type screwdriver

Weak suction

|

a)  The distance is too far between the cooker hood and hob.

b)  There are many windows (doors) causes strong wind convection.

c)  If due to the position of cooker hood install upon the window, you may put a three-ply board on the back of the cooker hood to cover the spaces.

|

“+” type screwdriver“+”

Tilting hood

|

a)  Adjust the height of the model where it is hung on the ceiling.

b)  If the model tilt forward, lock the wall with wood screw again (the screw peep out around 0.5~1 cm from the wall), or check the screw that fixing the model are loose or not.

|

“+” type screwdriver

Lamp does not light-up| Take the screw off from the lamp shade and replace with a new light bulb, then fix the lamp shade back.| “+” type screwdriver

WARRANTY CARD

WARRANTY CONDITIONS

Subject to following Term & Conditions, **this equipment is guaranteed against defective material & **manufacturing defects by Fiamma Trading Sdn Bhd for a period of twelve (12) months from the date of original purchase. Fiamma Trading Sdn Bhd reserves the right to change these terms & conditions without **prior notice.**

Terms & **Conditions:**

• This warranty is valid & provided that warranty card is completed with authorized dealer’s stamp from the date of original purchase and in the territory of Malaysia only.

• This warranty covers repair or, at the option of Fiamma Trading Sdn Bhd, replacement of any parts proven to be defective due to defective workmanship or material provided that the product was purchased from an authorized dealer of Fiamma Trading Sdn

• This warranty does not cover the damage resulting from:

  • Any unauthorized disassembly , service repair , alteration or modification being carried
  • Abnormal voltage or the use of generator and/or used not in accordance with the Operating Manual/ Userl
  • Misuse , abuse, negligence or accident howsoever caused .
  • Normal wear or
  • Rough handling &
  • Commercial/ public use g. hotel, laundry, college, university, etc.

• This warranty does not cover the following accessories:

  • Burner Caps/Supports (b) Cast Iron Grib (c) Knobs (d) Body Work (e) Light Bulb (f) Charcoal/ Filter (g) Cover (h) Glass Cover I Screen (i) Trays/Shelves U) Hose

• This warranty is considered null & void in the events if:

  • Any item contained in this warranty card has been tempered with or altered in any way without the prior written consent of Fiamma Trading Sdn Bhd. Request for warranty services within the warranty period must be accompanied with this warranty card & proof of original
  • Any time during the warranty period, any part/ parts of this equipment is/ are removed, altered, tempered with, adjusted, modified, dismantled, repaired or handled in any way whatsoever by any person/ persons not authorized by us.
  • The serial number of the product has been defaced or

• Warranty for WINE CHILLER compressor is (5) five years, gas refill and labor charges are

• In the event of defects covered by this warranty arising during the warranty period, the purchaser shall be fully responsible for the due delivery to our dedicated service centre of the equipment (expect for the refrigerator, washing machine, ovens, cooker hood, gas cooker, dishwasher , dryer , built-in hob, freezer , water heater) for any work which shall need to be done pursuant to this warranty & subsequent collection thereof of the equipment after the said work has been done.

• This warranty is in lieu of any, and all other warranties expressed or implied warranty of merchantability or fitness for a particular Fiamma Trading Sdn Bhd assumes no liability for the breach of the warranty beyond correcting the breath in the manner described above. In no event shall Fiamma Trading Sdn Bhd be liable for consequential losses or damages, including loss of use or loss of profits resulting from the product.

Our Warranty

Customer Care

AFTER-SALES SERVICE:
Exact Quality Sdn. Bhd.
Hotline: 03-6286-9000
Email: egservice@fiamma.com.my

OPERATION HOURS
08:30am – 06:00pm
(Monday – Friday, except public holiday)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>