SW-MOTECH STP.05.590.10000/B Frame Slider Kit Instruction Manual
- June 13, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH STP.05.590.10000/B Frame Slider Kit
Product Information
Product Name: ANBAUANLEITUNG
Model Numbers: STP.05.590.10000/B, STP.05.590.80000/B, STP.00.590.10001/B
Revision: 02
Manufacturer: SW-MOTECH GmbH & Co. KG
Address: Ernteweg 7-10, 35282 Rauschenberg, Germany
Contact: Tel. +49 (0) 64 25/8 16 8-050, Fax +49 (0) 64 25/8 16 8-10
Email: info@sw-motech.com
Website: www.sw-motech.com
Product Usage Instructions
- Mount the Mounting Bracket on the left side of the motorcycle.
- Use M6 screws and tighten them to 9.6 Nm torque.
- Use M10 screws and tighten them to 46 Nm torque.
- Mount the Mounting Bracketon the right side of the motorcycle.
- Use M6 screws to secure the Mounting Bracket and tighten them to 9.6 Nm torque.
- Attach the Adapter Plate using the provided screws (FSH.00.008.001).
- Use Hexagon Socket Screws to secure the Upper Frame Clamp and tighten them to the specified torque.
- Use Hexagon Socket Screws and Washers to secure the Lower Frame Clamp .
- Attach the the provided screws (Hexagon Screw -.
- Use Hexagon Socket Screws and Washers to secure the Protection Stripe .
- Refer to the mounting instructions of the frame slider set (*) to complete the installation on the right side.
- Pay attention to the manufacturer’s specified torque for all screws, bolts, and nuts.
- Check all screws, bolts, and nuts after driving the first 50 km to ensure they are tightened properly.
- Use medium strength liquid thread-locker (e.g., Lock tite) to secure all screws, bolts, and nuts.
- Note: The mounting instructions of the frame slider set should be followed in addition to these instructions.
Mounting kit for frame slider SUZUKI SFV 650 Gladius ’09 –
Mounting Instructions
SW-MOTECH products should be installed by a qualified, experienced motorcycle
technician. If you are unsure of your ability to properly install a product,
please have the product installed by your local motorcycle dealer. SW Motech
takes no responsibility for damages caused by improper installation.
All screws, bolts and nuts, including all replacement hardware provided by SW-
MOTECH, should be tightened to the torque specified in the OEM maintenance
manual for your motorcycle. If no torque specifications are provided in the
OEM maintenance manual, the following torques may be used:
- M6 9,6 Nm
- M10 46 Nm
All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque.
Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts.
INFORMATION
Attention: First attach all parts of the frame slider on the left side of
the motorcycle, as shown in the drawings.
NOTE: Also refer to the mounting instructions of the frame slider set
(*).
Then attach all parts on the right side, similarly as on the left side. Use on
the right side mounting bracket (2) and screw (6).
Pay attention to the manufacturer’s specified torque.
MOUNTING INSTRUCTIONS
- Revision: 00
- Datum / Date: 10 – 2019
Crash pad set
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers· specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
Date of packaging:
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg Germany
Tel./ phone+ 49 (0)6425 / 8168 – 050 Fax / fax+ 49 (0)6425 / 8168 – 10
info@sw-motech.com www.sw-motech.com
Step| No.| Item No. / Description *| Part| Quantity ..| N-m “‘|
---|---|---|---|---|---|---
| (1 I| STP.00.590.020L / R| Crash Pad; left/ right| 2 /2| |
| | | | |
(2)| STP.00.590.021| Logo Insert| 212| |
| | | | |
(3)| 3,0 x 16| Lenshead Screw, self-tapping| 212| max. 1,2|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| Coarse Thread 01 M4 I M5 I M6 I MS I
M10 I M12| | | Coarse Thread 01 M4 I M5 I M
6 **1 ****MS I M10 I M12
Steel CL 8.8 N·m 2,8 5,5 9,6 23 46 79| SteelCL10.9
N·m** 4,1 8,1 14 34 67 115
MOUNTING
- Step [1]: Attach the crash pads (1 I on both sides to the adapter plates of your SW-MOTECH slider set for frame, as described in the mounting instructions of the slider set for frame.
- Step [2]: Place the logo inserts (2) on both sides into the crash pads …
- Step [3]: … and attach them with the screws (31.
Tighten the screws (3) CAREFULLY by hand (max. 1,2 N-m) !
Copyright by .sw MOTECH GmbH & co.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>