BEGA 50070.3 Wall Luminaire for Indoor Use Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 50070.3 Wall Luminaire for Indoor Use Instruction Manual
Instructions for use
Application
Free radiating wall luminaire · indoor luminaire with hand-blown three-ply
opal glass for a soft and uniform light distribution. The elongated design of
this wall luminaire particulary provides suitability for installation on
pillars, columns and for the front surface of walls, as well as for recesses
or profiles. The luminaire may be installed horizontally or vertically
Product description
- Metal luminaire housing, finish Chrome
- Hand-blown opal glass
- The electrical equipment can be hinged 2 mounting holes ø 6mm
- Distance apart 640mm Jointing sleeve with cable entry for mains supply cable up to ø 14 mm, max. 5 x 1.5@
- Connecting terminals 2.5@
- Earth conductor terminal
- LED power supply unit 220-240 V x 0/50-60 Hz
- DC 176-276 V
- During DC operation the LED power is reduced to 15%
- DALI-controllable
- Basic insulation is provided between the mains and control cables
- BEGA Thermal Control®
- Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets
- Impact strength IK02
- Protection against mechanical impacts < 0.2 joule
- Safety mark
- Conformity mark
- Weight: 4.4 kg
- This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e.g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Lamp
Module connected wattage: 34.8 W
Luminaire connected wattage : 39 W
Rated temperature: ta=25 °C
Ambient temperature: ta max=35 °C
50 070.3K3
Module designation : 6x LED-0627/930
Colour temperature: 3000 K
Colour rendering index : CRI > 90
Module luminous flux : 5790 lm
Luminaire luminous flux : 3556 lm
Luminaire luminous efficiency: 91,2 lm/W
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping. Undo
hexagon socket (wrench size 5) in the locking cap and remove it. The opal
glass can now be hinged together with the electrical equipment to the front.
Remove opal glass. Note position of application of the luminaire »arrow down«.
Drill mounting holes into the mounting surface – spacing 640 mm and turn in
enclosed or suitable fixing screws. For the electrical connection undo the
screw connection at the line connector and remove terminal block. Make earth
conductor connection and electrical connection. Make connection of the phase
with the L marked, the neutral wire at the N marked and earth conductor at the
PE marked connecting terminal. For digital actuation please use the two
connecting terminals DA. If these terminals are not assigned, the luminaire
will work with full light output. Bolt together both screw cable glands
firmly. Hook luminaire into the fixing screws and tighten. Slide opal glass
over the lamp and fasten with the locking cap. Make sure that the gaskets are
positioned correctly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt. Defective
glass must be replaced.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module. Defective
glass must be replaced. Close the luminaire.
Spares
Spare glass: 11 003 176 .1RG
LED power supply unit : DEV-0159/700i
LED module 3000 K : LED-0627/930
Gasket glass : 2x 83 000 788
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>