Laserliner StarSensor 150 Detects Wall and Crossbeams Instructions

: June 4, 2024
: Laserliner

Table of Contents

Laserliner StarSensor 150 Detects Wall and Crossbeams
Function / Application
General safety instructions
Additional information on use
Safety instructions
Inserting batteries
Operation
Information on maintenance and care
EU directives and disposal
SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Laserliner StarSensor 150 Detects Wall and Crossbeams

Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and if the laser device is passed on, this document must be passed on with it.

Function / Application

This electronic locating device finds wall beams and joists as well as live wires. The device analyses the surface at nine points simultaneously and signals the detection of concealed objects via the LED display.

General safety instructions

The device must only be used in accordance with its intended purpose and within the scope of the specifications.
The structure of the device must not be modified in any way.
Do not expose the device to mechanical stress, extreme temperatures, moisture or significant vibration.
Do not work alone in the vicinity of hazardous electrical installations and only under the guidance of a qualified electrician.

Additional information on use

Observe the technical safety regulations for working on electrical systems, especially:

Safely isolating from power supply,
Securing to prevent system being switched on again,
Checking zero potential, two-pole,
Earthing and shortcircuiting,
Securing and covering adjacent live components.

Safety instructions

Dealing with electromagnetic radiation

The measuring device complies with electromagnetic compatibility regulations and limit values in accordance with EMC-Directive 2014/30/EU.
Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.
The measuring accuracy may be affected when working close to high voltages or high electromagnetic alternating fields.

Laserliner-StarSensor-150-Detects-Wall-and-Crossbeams-
fig-1

LED-Indicator
Live wire warning
ON
Battery compartment

Inserting batteries

Open the battery compartment and insert batteries (2 x type AAA) according to the symbols. Be sure to pay attention to polarity.

Operation

Device on: Press and hold the On button (3).

Scan: The LEDs indicate the center and the edges of beams and hidden objects.

Laserliner-StarSensor-150-Detects-Wall-and-Crossbeams-
fig-3

Live wire warning: The presence of live lines is indicated when the lightning symbols light up.
Device off: Release the On button (3).

Detecting wooden wall beams and joists as well as metal in drywall structures, e.g. under gypsum fibreboard, wood panels or other non-metallic cladding. Move the tool slowly across the surface.

Tip 1: To avoid interference while scanning, keep your free hand and other objects at least 15 cm away from the StarSensor 150.

Tip 2: Ensure that you have really detected a stud. To do so, check on both sides whether other studs are present at equal distances, usually at 30, 40 or 60 cm. Also check that it is a stud by scanning at several places directly above and below the position of the first find.

Note: If an object is deep inside a wall, the device may not indicate it clearly.

If electric wires or metal or plastic pipes are located near or in contact with a plaster fibreboard panel, they may be identified by the StarSensor 150 as studs.

Special things to note with various materials
It may not be possible to detect wooden studs or joists through the following materials:

Ceramic floor tiles
Fitted carpeting with padded backing
Wallpaper with metal fibres or metal foil
Freshly painted, damp walls. These must have dried for at least one week.

Always switch off the power supply when working near electric wires.

Information on maintenance and care

Clean all components with a damp cloth and do not use cleaning agents, scouring agents and solvents. Remove the battery(ies) before storing for longer periods. Store the device in a clean and dry place.

Technical Data

(Subject to technical changes without notice. 21W47)

Detection range AC| 110 – 230V, 50 – 60 Hz
Power supply| 2 x 1.5V LR03 (AAA)
Operating conditions| 0°C … 40°C, max. humidity 20

… 90% rH, no condensation

EU directives and disposal

This device complies with all necessary standards for the free movement of goods within the EU. This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment.
Further safety and supplementary notices at: http://laserliner.com/info?an=ALP