BEGA 31071 Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 31071 Wall Luminaire
Dimension
Application
Unshielded wall luminaire with high protection class.
A luminaire made of aluminium alloy and crystal lass.
Product description
Luminaire made of aluminium alloy,
aluminium and stainless steel
BEGA Unidure® coating technology
Crystal glass
Silicone light diffuser
Mounting plate with 2 fixing
holes ø 4.4mm · 60 x 95mm spacing
2 cable entries for through-wiring of mains
supply cable ø 7-12mm
2 loose connectors 3-pole, max. 4mm²
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit
220-240 V ≂ 0/50-60 Hz
DC 176-280 V
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK02
Protection against mechanical impacts < 0.2 joule
– Conformity mark
Weight: 2.6 kg
This product contains light sources of energy efficiency class(es) C
Safety
The installation and operation of this luminaire are subject to national
safety regulations
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage 9.5 W
Luminaire connected wattage 10.8 W
Rated temperature ta=25 °C
Ambient temperature ta max=50 °C
31 071K3
Module designation LED-1324/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 1835 lm
Luminaire luminous flux 894 lm
Luminaire luminous efficiency 82,8 lm/W
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Undo hexagon socket head screw (wrench size 3mm) up to the stop and
disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Fix the mounting plate with enclosed or any other suitable fixing material
onto the mounting surface.
Establish the earth conductor connection at the terminal of the mounting plate
marked with .
Push silicone sleeves over the lines and make electrical connection at the
loose plug-in terminals.
Connect the green and yellow protective earth conductor from the luminaire top
to the terminal marked in the mounting plate.
Place luminaire housing onto the mounting plate and fix it.
Make sure that gasket is positioned correctly
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced. Close the luminaire.
Spares
LED power supply unit DEV-0451/350
LED module 3000 K LED-1324/830
Spare glass with frame graphite 75 005 352
Spare glass with frame bronze 75 005 353
Gasket base 83 001 926
Gasket connection housing 83 002 074
Gasket housing 2x 83 002 201
Customers Support
2/2 BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com
www.bega.com