JADEMAR LIGHTING JRPT-M01 Series Post Top Ceiling Light Instruction Manual

: June 12, 2024
: JADEMAR LIGHTING

Table of Contents

JADEMAR LIGHTING JRPT-M01 Series Post Top Ceiling Light
Product Information
Product Usage Instructions
INSTALLATION INSTRUCTIONS
SUSPENDED RING MOUNT
WIRE CONNECTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JADEMAR LIGHTING JRPT-M01 Series Post Top Ceiling Light

Product Information

The JRPT-M01 Series is a post top lighting fixture designed for outdoor use. It must be installed by a licensed electrician and in accordance with the national electric code (NEC) and all applicable electric codes and safety standards. This product should only be used in environments that do not contain corrosive gas liquids or high pressure water vapor. Any alteration or modification of the product is strictly forbidden, as it may cause personal injury, property damage, or product malfunction. The product must be properly grounded to prevent electrical shock or malfunction. The fixture is available in three different color temperatures (3000K, 4000K, and 5000K) and various wattages (130W, 87W, 70W, and 45W). It features a Y-pole junction box for mounting and a waterproof plug for secure installation.

Product Usage Instructions

Step 1: Remove the top cover by loosening eight (8) M5*16 top cover set screws and separate the cable joint connector.
Step 2: Push the Y-pole horizontally along the fixture track groove and secure the fixture and Y-pole with four (4) M6*12 set screws.
Step 3: Feed the supply wire through the center of the tenon and the center hole in the post top arms. Make cable joint connector connections with the driver and snap the cover into place. Secure the top cover with eight (8) M5*16 screws and ensure that the eight (8) rubber covers are in the corresponding position.
Step 4: Unscrew the waterproof plug and pull the fixture lead. Center the luminaire on the tenon and tighten the supplied set screws to securely mount the luminaire. Connect the wires (voltage to black, white to common, green to ground). Once all connections are made, carefully push all wires down into the junction box and secure it with the waterproof plug.

Note: Make sure to aim the upper cover arrow at the lower cover arrow when closing the cover.
For any additional information or inquiries, please contact JadeMar at info@jademar.com or call 305.640.0465.

INSTALLATION INSTRUCTIONS

JRPT-M01 SERIES / POST TOP
WARNING BEFORE YOU BEGIN READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

To prevent personal injury or product damage only licensed electricians should install.
To avoid electric shock or component damage disconnect power before a?emp ng installa on or servicing.
This product must be installed in accordance with the na onal electric code (NEC) and all applicable federal, state and local electric codes and safety standards.
Disconnect product and allow cooling prior to servicing.
Any altera on or modiﬁca on of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunc on.
To prevent product malfunc on and/or electrical shock this product must be properly grounded.
This luminaire is designed to operate in ambient temperatures ranging from -40°C to 45°C and to be horizontally mounted with the LEDs facing down.
This product must be installed in accordance with the applicable installa on code by a Person familiar with the construc on and opera on of the product and
the hazards involved.
This product is not available for several special environments, such as places with corrosive gas liquids or high pressure water vapor.

MIN 75°C SUPPLY CONDUCTORS. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
CAUTION – RISK OF FIRE.

SUSPENDED RING MOUNT

Step 1:
Remove top cover by loosening eight (8) M5*16 top cover set screws and seperate the cable joint connector. NOTE : CCT Power Regulator Mode：Remove the upper cover screw, open the cover, adjust the color temperature power regulator to the desired value as shown in the gure below, then close the cover and lock it with screws
Step 2:
Push the Y-pole horizontally along the ﬁxture track groove and secure the ﬁxture and Y-pole with (4) M6*12 set screws.
Step 3:
Feed supply wire through center of the tenon and through center hole in post top arms and make cable joint connector connec ons with driver; and cover should snap into place according to the arrow; secure top cover with (8) M5*16 screws and make sure (8) rubber cover in the corresponding posi on.
Step 4:
- Unscrew the waterproof plug pull the ﬁxture lead, center luminaire on tenon and ghten supplied set screws to securely mount luminaire to tenon and pull the ﬁxture lead. Remark: 3’’ tenon(default se?ng); 2 3/8 pole adapter provided.
- Connect wires (voltage to black, white to common, green to ground).
- Once connec ons are completely made, carefully push all wires down into the junc on box and secure it with waterproof plug.
Step 1:
Remove top cover by loosening eight (8) M5*16 top cover set screws and seperate the cable joint connector. NOTE : CCT Power Regulator Mode: Remove the upper cover screw, open the cover, adjust the color temperature power regulator to the desired value as shown in the gure below, then close the cover and lock it with screws.
Step 2:
Push the single arm horizontally along the ﬁxture track groove and secure the ﬁxture and Y-pole with (2) M6*12 set screws.
Step 3:
Feed supply wire through center of tenon and through center hole in post top arms and make cable joint connector connec ons with driver; and cover should snap into place according to the arrow; secure top cover with (8) M5*16 screws and make sure (8) rubber cover in the corresponding posi on.
Step 4:
- Unscrew the waterproof plug pull the ﬁxture lead, center luminaire on tenon and ghten supplied set screws to securely mount luminaire to tenon and pull the ﬁxture lead. Remark: 3’’ tenon(default se?ng); 2 3/8 pole adapter provided.
- Connect wires (voltage to black, white to common, green to ground).
- Once connec ons are completely made, carefully push all wires down into the junc on box and secure it with waterproof plug.