JADEMAR LIGHTING JFL-PS 90W Floodlight Instruction Manual

June 9, 2024
JADEMAR LIGHTING

JADEMAR LIGHTING JFL-PS 90W Floodlight Instruction Manual
JADEMAR LIGHTING JFL-PS 90W Floodlight

WARNINGS

  • DO NOT USE AN ELECTRIC GENERATOR TO TEST THE LAMP.
  • Please abide by country, regional and local law and regulaons when installing this fixture.
  • Please turn off the power before installaon or maintenance.
  • Proper earth grounding is required to ensure safety.
  • To avoid possibility of electrical shock or fire, the installer must be a licensed electrician.
  • Please wear gloves to avoid injury before installaon.
  • During or aer installaon, if there are situaons such as smoke, fire in the wires or lamps, please turn off the power immediately and nofy relevant personnel for an overhaul.
  • This light can be used for outdoor installaon.
  • Please check if there is any damage during shipping. If so, please contact manufacturer mely.
  • Please read the installaon instrucon carefully to check whether all the accessories are complete. Aer confirmaon, then install the fixture according to installaon steps.

WIRING DIAGRAM

WIRING DIAGRAM

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – TRUNNION MOUNTING

Step 1: Pass the input wire of the fixture through the bracket (Figure 4);
Step 2: Fix the bracket (Figure 5).

Installation

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – YOKE MOUNTING

Step 1: Take out the bracket; ghten the screws, and fix the bracket on the fixture (Figure 6).

Installation

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – UNIVERSAL BRACKET

MOUNTING

Step 1: Separate the bracket with tool (Figure 13);
Step 2: Pass the input wire of the fixture through the bracket (Figure 14);
Step 3: Pass the input wire through the bracket and lock the bracket (Figure 15).

INSTALLATION

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – YOKE MOUNT TO UNIVERSAL BRACKET MOUNT

Step 1: Take out the bracket; Tighten the screws, fix the bracket on the fixture (Figure 24);
Step 2: Separate the bracket with tool (Figure 25);
Step 3: Pass the input wire of the fixture through the bracket (Figure 26);
Step 4: Pass the input wire through the bracket and lock the bracket (Figure 27)..

INSTALLATION

INSTALLATION INSTRUCTIONS OF LED LAMPS – TRUNNION MOUNTING

Step 1: Drill holes on the wall as shown (Figure 30);
Step 2: Knock the expansion bolts into the wall (Figure 31);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 32).
Noce: Adjustable angle is 0~+/-90° (Figure 32)

INSTALLATION

INSTALLATION INSTRUCTIONS OF LED LAMPS – YOKE MOUNTING

Step 1: Drill holes on the wall as shown (Figure 33);
Step 2: Knock the expansion bolts into the wall (Figure 34);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 35).
Noce: Adjustable angle is 0~+/-180° (Figure 35)

INSTALLATION

INSTALLATION INSTRUCTIONS OF LED LAMPS – UNIVERSAL BRACKET 4 IN 1

Instruction

Step 1: Remove the spare parts, the remaining parts as shown in Figure 39;
Step 2: Loosen the 4 locking bolts on the slip fier, connect the wires correctly and put the wire into pole. Then fasten the locking bolts between slip fier and the pole (Figure 40);
Step 3: Loosen the fixing bolts and adjusng bolts, adjust fixture angle as per actual demands. Tighten adjusng bolt and fixing bolts aer the angle is confirmed (Figure 40).
Noce: Adjustable angle is 0~+/-90° (Figure 40)

INSTALLATION INSTRUCTIONS OF LED LAMPS – UNIVERSAL BRACKET 4 IN 1

Step 1: Change the rubber plug on the Installaon bar to the A&DM bracket (Figure 41);
Step 2: Fix the DM bracket to the square pole by bolt. Connect the power cable with pole cable, make sure good protecon on wire connecon, and put the wire in the DM bracket; close the side lid and ghten it, (Figure 42) then finish installaon.
Noce: Adjustable angle is 0~+/-90° (Figure 42)
Noce: Round pole should be with adapng plate (Figure 43).

Instruction Aenon: When the photocell funcon is required, photocell should be installed on the back of lamp; When it’s not required, shorng cap should be installed on the back of lamp (Figure 44)

COLOR TEMPERATURE ADJUSTMENT INSTRUCTIONS

Standard wire:
L/live wire: Black\Brown;
N/null wire: White\Blue;
Ground wire: Green\Yellow-green.

Step 1: Find the switch to adjust CCT (Figure 45);
Step 2: Light up the lamp, push aside the fixing piece to show the black buon, and adjust the color temperature by pressing the black buon (Figure46);
Step 3: Once the color temperature is confirmed, return the fixing piece back to the original posion and ghten the screw to lock the fixing piece (Figure 47).

ADJUSTMENT INSTRUCTIONS

WARNING/AVERTISSEMENT

MIN 90 °C SUPPLY CONDUCTOR
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS

  • DO NOT USE AN ELECTRIC GENERATOR TO TEST THE LAMP.
  • Please abide by country, regional and local law and regulaons when installing this fixture.
  • Please turn off the power before installaon or maintenance.
  • Proper earth grounding is required to ensure safety.
  • To avoid possibility of electrical shock or fire, the installer must be a licensed electrician.
  • Please wear gloves to avoid injury before installaon.
  • During or aer installaon, if there are situaons such as smoke, fire in the wires or lamps, please turn off the power immediately and nofy relevant personnel for an overhaul.
  • This light can be used for outdoor installaon.
  • Please check if there is any damage during shipping. If so, please contact manufacturer mely.
  • Please read the installaon instrucon carefully to check whether all the accessories are complete. Aer confirmaon, then install the fixture according to installaon steps.

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – TRUNNION MOUNTING

Step 1: Pass the input wire of the fixture through the bracket (Figure 1);
Step 2: Fix the bracket (Figure 2).

TRUNNION MOUNTING

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – YOKE MOUNTING

Step 1: Take out the bracket; ghten the screws, and fix the bracket on the fixture (Figure 3).

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – UNIVERSAL BRACKET MOUNTING

Step 1: Separate the bracket with tool (Figure 4);
Step 2: Pass the input wire of the fixture through the bracket (Figure 5)
Step 3: Pass the input wire through the bracket and lock the bracket (Figure6).

INSTRUCTIONS

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – SLIP FITTER TO UNIVERSAL BRACKET MOUNTING

Step 1: Separate the bracket with tool (Figure 10);
Step 2: Pass the input wire of the fixture through the bracket (Figure 11);
Step 3: Pass the input wire through the bracket and lock the bracket (Figure12).

INSTALLATION

INSTALLATION INSTRUCTIONS OF LED LAMPS – TRUNNION MOUNT TO WALL PLATE

Step 1: Drill holes on the wall as shown (Figure 13);
Step 2: Knock the expansion bolts into the wall (Figure 14);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 15).
Noce: Adjustable angle is 0~+/-90° (Figure 15)

INSTALLATION

INSTALLATION INSTRUCTIONS OF LED LAMPS – YOKE MOUNT TO WALL PLATE

Step 1: Drill holes on the wall as shown (Figure 16);
Step 2: Knock the expansion bolts into the wall (Figure 17);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires property and put them into juncon box (Figure 18).
Noce: Adjustable angle is 0-+/-180° (Figure 18)

INSTALLATION

INSTALLATION INSTRUCTIONS OF LED LAMPS – UNIVERSAL BRACKET

Step 1: Remove the spare parts, the remaining parts as shown in Figure 22:
Step 2: Loosen the 4 locking bolts on the slip fier, connect the wires correctly and put the wire into pole. Then fasten the locking bolts between slip fier and the pole (Figure 23);
Step 3: Loosen the fixing bolts and adjusng bolts, adjust fixture angle as per actual demands. Tighten adjusng bolt and fixing bolts aer the angle is confirmed (Figure 23).
Noce: Adjustable angle is 0~+/-90° (Figure 23)

INSTRUCTIONS

INSTALLATION INSTRUCTIONS OF LED LAMPS – UNIVERSAL BRACKET SQUARE & ROUND POLE

Step 1: Change the rubber plug on the Installaon bar to the A&DM bracket (Figure 24);
Step 2: Fix the DM bracket to the square pole by bolt. Connect the power cable with pole cable, make sure good protecon on wire connecon, and put the wire in the DM bracket; close the side lid and ghten it, (figure 25) then finish installaon.
Noce: Adjustable angle is 0~+/-90° (Figure 25)
Noce: Round pole should be with adapng plate (Figure 26).

INSTRUCTIONS

Aenon: When the photocell funcon is required, photocell should be installed on the back of lamp; When it’s not required, shorng cap should be installed on the back of lamp (Figure 27)

COLOR TEMPERATURE ADJUSTMENT INSTRUCTIONS

Step 1: Find the switch to adjust CCT (Figure 28);
Step 2: Light up the lamp, push aside the fixing piece to show the black buon, and adjust the color temperature by pressing the black buon (Figure29);
Step 3: Once the color temperature is confirmed, return the fixing piece back to the original posion and ghten the screw to lock the fixing piece (Figure 30).

INSTRUCTIONS

Waage Adjustable Instrucon

  1. Unscrew the plug with screwdriver or coin (Figure 31)
  2. Adjust the waage adjustable dial switch to different gear which match to corresponding waage (Figure 31) First gear please tum to E7, 2nd gear (full power) please turn to I, 1st to 2nd gear refer to lower waage to full waage.
  3. Please re-install the plug aer adjustment.
    Note: Please turn off the power before adjust waage.

WARNING/AVERTISSEMENT:
MIN 90 °C SUPPLY CONDUCTORS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS

  • DO NOT USE AN ELECTRIC GENERATOR TO TEST THE LAMP.
  • Please abide by country, regional and local law and regulaons when installing this fixture.
  • Please turn off the power before installaon or maintenance.
  • Proper earth grounding is required to ensure safety.
  • To avoid possibility of electrical shock or fire, the installer must be a licensed electrician.
  • Please wear gloves to avoid injury before installaon.
  • During or aer installaon, if there are situaons such as smoke, fire in the wires or lamps, please turn off the power immediately and nofy relevant personnel for an overhaul.
  • This light can be used for outdoor installaon.
  • Please check if there is any damage during shipping. If so, please contact manufacturer mely.
  • Please read the installaon instrucon carefully to check whether all the accessories are complete. Aer confirmaon, then install the fixture according to installaon steps

WIRING DIAGRAM

WIRING DIAGRAM

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – TRUNNION TO YOKE MOUNTING
Step 1: Put the input wire of the light across the bracket. (Figure 7)
Step 2: Fix the bracket. (Figure 8)
Step 3: Take out the bracket; let the input wire go through the cover or the back cover of the light, then fix the cover and ghten the screws, fix the bracket on the fixture. (Figure 9)DIFFERENT BRACKETS

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS -= UNIVERSAL BRACKET
Step 1: Separate the bracket with tool. (Figure 10)
Step 2: Put input wire of the light across the bracket. (Figure 11)
Step 3: Let input wire go through the bracket and lock the bracket. (Figure12)

UNIVERSAL BRACKET

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – TRUNNION TO WALL MOUNT
Step 1: Drill holes on the wall as shown. (Figure 16)
Step 2; Knock the expansion bolts into the wall (Figure 17)
Step 3: Connect the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box. (Figure 18)
Noce: Adjustable angle is 0~+/-90* (Figure 18)

TRUNNION TO WALL MOUNT

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – YOKE MOUNTING TO WALL PLATE

Step 1: Drill holes on the wall as shown. (Figure 19)
Step 2: Knock the expansion bolts into the wall (Figure 20)
Step 3: Connect the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 21)
Noce: Adjustable angle is 0-+/-90* (Figure 21)

YOKE MOUNTING TO WALL PLATE

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – UNIVERSAL BRACKET
Step 1: Remove the spare parts, the remaining parts such as (Figure 22)
Step 2: Loosen the 4 locking bolts on the slip fier, connect the wire correctly and put the wire into pole. Then fasten the locking bolts between slip fier and the pole. (Figure 23)
Step 3: Loosen the fixing bolts and adjusng bolts, align the fixture to required angle. Tighten adjusng bolt and fixing bolts aer the angle is confirmed. (Figure 23)
Noce: Adjustable angle is 0-+/-90° (Figure 23)

UNIVERSAL BRACKET

INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS – UNIVERSAL BRACKET SQUARE & ROUND POLE

Step 1: Change the rubber plug on the Installaon bar to the AM&DM bracket. (Figure 24)
Step 2 : Fix the DM bracket to the square pole by bolt. Connect the power cable with pole cable. Make sure good protecon on the wire connecon, and put the wire in the DM bracket; close the side lid and ghten it, (figure 25) then finish installaon.
Noce: Adjustable angle is O~+/-90° (Figure 25)
Noce: Round pole should be with adapng plate. (Figure 26)

UNIVERSAL BRACKET

NOTES

Aenon: When the photocell funcon is required, photocell should be installed
on the back of lamp; When it’s not required, shorng cap should be installed on the back of lamp (Figure 27)
Standard wire:
L/live wire; Black\Brown;
N/null wire: White Blue;
Ground wire: Green Yellow-green

instruction

Step 1. Waage Adjustable Instrucon Unscrew the plug with screwdriver or coin  Figure 28)
Step 2. Adjust the waage adjustable dial switch to different gear which match to corresponding waage (Figure 28)
First gear please turn to 2nd gear please turn 3rd gear please turn to 4th gear (full power) please. turn 1st to 4th gear refer to lower waage to full waage
Step 3. Please re-install the plug aer adjustment.
Note: Please turn off the power before adjusng waage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

JADEMAR LIGHTING User Manuals

Related Manuals