BEGA 50432.1 Recessed Ceiling Downlight Instructions

BEGA 50432.1 Recessed Ceiling Downlight

Product Information

Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Module Information:

• Module Designation : 50 432.1 K3
• Color Temperature: 3000 K
• Colour Rendering Index (CRI) : > 80
• Module Luminous Flux: 4365 lm
• Luminaire Luminous Flux: 3516 lm
• Luminaire Luminous Efficiency : 121.2 lm/W

Power Supply Units:

• On/Off Power Supply Unit: 13 145
• DALI Power Supply Unit : 13 171

Spares:

• Trim Ring: Abschlussring
• LED Module 3000 K Reflector: LED-0785/830

Product Usage Instructions

To connect the luminaire, follow these steps:

1. Connect the LED power supply unit to the luminaire.
2. Route the LED power supply unit through the installation housing and place it in the suspended ceiling.
3. Connect the 2-pin plug connector between the luminaire and the external LED power supply unit.

To replace the LED module, follow these steps:

1. Identify the designation of the LED module from the label in the luminaire.
2. Ensure that the light color and light output of the replacement module correspond to the original modules.
3. Disconnect the system and open the luminaire.
4. Refer to the installation instructions for the LED module and follow them carefully.
5. Close the luminaire after replacing the module.

Note: The power supply units are only suitable for the operation of one LED luminaire. For accessories, a separate instructions for use can be provided upon request.

Dimension

Instructions for use

Application

• Recessed ceiling downlight · Interior luminaire with symmetrical narrow beam light distribution for connection to an external LED power supply unit.
• For surface-mounted installation in indoor suspended ceilings of 5-25mm thickness.

Product Description

• Recessed luminaire without power supply unit

• Luminaire housing made of cast aluminum

• Installation housing is made of glass-fibre reinforced polyamide with 2 fastening springs

• Reflector surface is made of pure aluminum

• Optical silicone lens · BEGA Hybrid Optics®

• Ceiling trim ring is made of metal, Colour white

• Safety glass

• Recessed opening ø 188mm

• Required installation depth 130mm 1 connecting cable with strain relief and plug connector system for BEGA power supply unit, on/off or DALI

• Safety Class III 3
  c – Conformity mark

• Weight: 1.6 kg

• This product contains light sources of energy efficiency class(es) D

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Lamp

• N25 W
• Luminaire connected wattage 29 W
• Rated temperature ta=25 °C
• Ambient temperature ta max=45 °C
• When installed in heat-insulating material ta max=25 °C

50 432.1K3

• Module designation LED- 0785/830
• Color temperature 3000 K
• Color rendering index CRI > 80
• Module luminous flux 4365 lm
• Luminaire luminous flux 3516 lm
• Luminaire luminous efficiency 121,2 lm/W

Installation

• A separate power supply unit is required to operate the luminaire.
• For connection to the external LED-power supply unit – accessory 13 145 or 13 171 – the luminaire is equipped with a 2-pin connector.
• Note the operating instructions of the LED-power supply units.
• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• The recessed opening is covered by the frame of the luminaire housing.
• Fixing the installation housing in the recessed opening is achieved by using two adjustable springs.

Installation into inserted ceilings:

• A recessed opening of 188 mm is necessary to accept the installation housing. Recessed depth min. 130 mm.
• Compress the fastening springs of the installation housing against their spring pressure on both sides towards the housing and slide the installation housing into the recessed opening.
• The fastening springs catch the ceiling panel from the backside. The minimum thickness of the ceiling panel is 5 mm. If the minimum thickness of the panel is less than 5 mm it must be reinforced from the reverse side.
• The maximum thickness of the ceiling panel must be no more than 25 mm.
• Fix the installation housing in the ceiling panel with two enclosed fastening screws (see sketch).
• Connect to the LED power supply unit.
• Route the LED power supply unit through the installation housing and place it in the suspended ceiling.
• Connect the 2-pin plug connector between the luminaire and the external LED power supply unit.
• Press together the two internal fixing sliders inside the luminaire housing.
• Push the luminaire housing to the end of the installation housing and then release the fixing sliders.
• This mechanism ensures that the luminaire housing sits securely inside the installation housing.
• Please use the protective gloves provided for the installation to prevent fingerprints on the reflector.
• Place the reflector with silicone lens on the ceiling trim ring. Twist the ceiling trim ring complete with the attached reflector to the right to fix the assembly inside the luminaire housing.

Cleaning · Maintenance

• Clean the luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the system and open the luminaire.
• Please follow the installation instructions for the LED module.
• Close the luminaire.

Accessories

• Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
• 13 145 Power supply unit on/off
• 13 171 Power supply unit DALI
• The power supply units are only suitable for the operation of one LED luminaire.
• For the accessories, separate instructions for use can be provided upon request.

Spares

• Trim ring 20 000 047M
• LED module 3000 K LED-0785/830
• Reflector 76 00 1 613 .1M
• BEGA Gantenbrink-Leuchten KG
• Postfach 3160
• 58689 Menden
• info@bega.com
• www.bega.com

Documents / Resources

| BEGA 50432.1 Recessed Ceiling Downlight [pdf] Instructions
50432.1 Recessed Ceiling Downlight, 50432.1, Recessed Ceiling Downlight, Ceiling Downlight, Downlight
---|---

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>