HYTRONIK HED7030/BT Bluetooth Dimmable LED Driver User Manual

: June 12, 2024
: HYTRONIK

Table of Contents

References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HYTRONIK HED7030/BT Bluetooth Dimmable LED Driver User Manual

Product Description
HED7030/BT is a Bluetooth dimmable LED driver, with maximum power output of 30W. It come with Switch-Dim interface by using Push switch (retractive switch) and of course Bluetooth dimming interface. The driver comes with an RJ12 terminal, ready to plug in a wide selection of motion sensors, ranging from HF to PIR, from low bay to high bay etc. It is ideal for direct projects or new luminaires design for lighting manufacturers. With Bluetooth wireless mesh networking, it makes communication between luminaires much easier without time-consuming hardwiring, which eventually saves costs for projects. Meanwhile, simple device setup and commissioning can be done via app

App Features

Quick setup mode & advanced setup mode
Floorplan feature to simplify project planning
Web app/platform for dedicated project management
Koolmesh Pro iPad version for on-site conguration
Grouping luminaires via mesh network
Scenes
Detailed motion sensor settings
Push switch conguration
Schedule to run scenes based on time and date
Astro timer (sunrise and sunset)
Staircase function (primary & secondary)
Internet-of-Things (IoT) featured
Device rmware update over-the-air (OTA)
Device social relations check
Bulk commissioning (copy and paste settings)
Power-on status (memory against power loss)
Ofine commissioning
Different permission levels via authority management
Network sharing via QR code or keycode
Remote control via gateway support HBGW01
Interoperability with Hytronik Bluetooth product portfolio
Compatible with EnOcean switch EWSSB/EWSDB
Continuous development in progress…

Hardware Features

Switch-Dim
PWM 1KHz (1-100%)
Bluetooth dimmable control
Insulated terminal cover with cord restraint
Standby power <0.5W
Active PFC design
Logarithmic Dimming
Linear Dimming
Congurable constant current (CC) output via DIP switch
Loop-in and loop-out terminals for efcient installation
Open-circuit Protection
Short-circuit Protection
Overload Protection
5-year warranty, designed for long lifetime up to 50,000 hours

Certain scenes which require external photocell can be achieved by using together with Hytronik Bluetooth sensors,such as HBIR29, HCD038/BT + sensor head etc

Qr Cod Scanner

Fully support
EnOcean switch
EWSSB/EWSDB

Output Configuration

Output Configuration

Warning: Please make sure the correct current is selected before starting the driver!

Technical Specifications

Bluetooth Transceiver

Operation frequency| 2.4 GHz – 2.483 GHz
Transmission power| 4 dBm
Range (Typical indoor)| 10~30m
Protoco| 5.0 SIG Mesh
Input

Mains Voltage| 220~240VAC 50/60Hz
Mains Current| 0.17~0.16A
Power Factor| 0.9
Max. Efficiency| 86%
Output

Output Current| 350mA~900mA
Output Voltage| 10-57V
Uout Max.| 75V
Turn-on Time| <0.5s
Dimming Interface| Switch-Dim
Environment

Operation Temp.| -20 ~ +50℃
Case Temp. (Max.)| 80℃
IP Rating| IP20
Safety and EMC

| EN55015, EN61547, EN6100-2/3,
EMC Standard| EN300328,EN301489-1/-17,
| EN62479
Safety Standard| EN61347-1, EN61347-2-13
Dielectric strength| Input→output: 3000VAC / 5mA /1min
Abnormal protection| Output short-circuit protection Overload ProtectionOpen- circuit Protection
Max. output power/current/voltage range

HED7030/BT| 3.5-20W/350mA /10-57V5-29W/500mA /10-57V5.5-30W/550mA /10-55V7-30W/700mA /10-43V7.5-30W/750mA /10-40V9-23W/900mA /10-25V

Mechanical Structure & Dimensions

Wire Preparation

To make or release the wire from the terminal, use a screwdriver to push down the button.

Wiring Diagram

Note: There is no need for any hardwirings on “push” terminal between one driver to another. The installer only needs to connect the push switches to the nearest driver to save labor and cost. The push switches can be assigned to control any Bluetooth driver through the app commissioning

Loading and In-rush Current

Model

| HEC7030/BF
---|---
In-rush Current (Imax.)| 38A
Pulse Time| 35 µs

Circuit Breaker Information

Automatic circuit breaker type

| B16A| B10A| B13A| B20A| B25A
---|---|---|---|---|---
HED7030/BT| 54| 34| 43| 67| 84

The data above is calculated according to the formula: Maximum Amount = 16/(Pn/230). In order to provide a more reliable reference in real application, the data have been revised to take 60% of the number calculated, i.e. 16/(Pn/230) x 60%. Please kindly take note that the calculation is based on ABB circuit breaker series S200. Actual values may differ due to different types of circuit breaker used and installation environment.

Performance Characteristics

Grape
Typical Efficiency vs Load

Grape
Typical Power Factor vs Load

Dimming Characteristics

Dim Level
Grape
Grape

Technical Specifications for Sensor Heads

PIR Sensor Properties

Sensor principle| PIR detection
Operating voltage| 5VDC

Detection range *

| HIR05 & HIR05/FM & HIR05/E & HIR07Max installation height：3mMax detection range：6m (diameter) HIR11Max installation height：15m (forklift)12m (single person) Max detection range： 24m (diameter)HIR12Max installation height：15m (forklift)12m (single person) Max detection range： 18m 6m (L W)
HF Sensor Properties

Sensor principle| High Frequency (microwave)
Operating voltage| 5VDC
Operation frequency| 5.8GHz +/- 75MHz
Transmission power| <0.2mW
Detection range *| SAM20 / SAM21 / SAM22Max installation height：3mMax detection range：12m (diameter) SAM23Max installation height：12mMax detection range：16m (diameter)

The detection range is heavily influenced by sensor placement (angle) and different walking paces. It may be reduced under certain conditions.

A. HIR05 PIR sensor head The cable length is around 65cm
B. HIR05/E PIR sensor head The cable length is around 65cm
C. HIR05/FM PIR sensor head The cable length is around 65cm.
D. HIR07 PIR sensor head Photocell Advance The cable length is around 30cm
E. HIR11/S PIR sensor head Surface mounting For high bay application IP65 (facia / lens part) The cable length is around 65cm
F. HIR11/F PIR sensor head Flush mounting For high bay application IP65 (facia / lens part) The cable length is around 65cm.
G. HIR11/C PIR sensor head Screw to the luminaire by conduit For high bay application IP65 (facia / lens part) The cable length is around 65cm.
F. HIR12 PIR sensor head For high bay application IP65 (facia / lens part) The cable length is around 65cm

Installation for HIR1

Thickness: 0.8mm – 1.6mm

We suggest that the metal plate thickness to be 0.8mm – 1.6mm to ensure perfect focal length for the PIR lens.

SAM20 HF sensor head Photocell AdvanceTM The cable length is around 30cm.

Product Dimension

SAM21 HF sensor head IP65 The cable length is around 65cm.
SAM22 HF sensor head Flush mount The cable length is around 65cm
SAM23 HF sensor head Photocell advance For highbay application The cable length is around 30cm.

Product Dimension

Detection Pattern

Ceiling mounted detection pattern (m)
SAM23

Ceiling mounted detection pattern (m)
SAM20 / SAM21 / SAM22

Subject to change without notice.
HIR05 & HIR05/FM & HIR05/E & HIR07b

HIR12
Change Without Notice

HIR11 (High-bay)

Lens | HIR11 : High-bay lens detection pattern for __**forklif t @ Ta = 20OC (Recommended installation height 10m-15m** )
A: Tangential movement Dimension

h = max.15m

insensitive sensitive

| B: Radial movement

h = max.15m

insensitive sensitive

__HIR11: High-bay lens detection pattern for single person @ Ta = 20 C(Recommended installation height 2.5m-12m )

A: Tangential movement Dimension

h = max.12m

insensitive sensitive

| B: Radial movement

h = max.12m

insensitive sensitive

Dimming Interface Operation Notes
Switch-Dim
The provided Switch-Dim interface allows for a simple dimming method using commercially available non latching (momentary) wall switches. Up to 64 LED drivers maybe connected to one switch. Detailed Push switch congurations can be set on Koolmesh app.

Switch Function	Action	Descriptions

Push switch

| Short press (<1 second)* Short press has to be longer than 0.1s, or it will be invalid.|

Turn on/off – Recall a scene-
Turn on only – Exit manual mode-
Turn off only – Do nothing

Double push|

Turn on only – Exit manual mode-
Turn off only – Do nothing-
Recall a scene

Long press (≥1 second)|

Dimming- Colour tuning- Do nothing

Simulate sensor| /|

Upgrade a normal on/off motion sensor to a Bluetooth controlled motion sensor

Additional Information / Documents

Regarding precautions for LED driver installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->LED Drivers – Precautions for Product Installation and Operation
To learn more about detailed product features/functions, please refer t www.hytronik.com/download->knowledge ->Introduction of App Scenes and Product Functions
Regarding precautions for Bluetooth product installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->Bluetooth Products – Precautions for Product Installation and Operation
Data sheet is subject to change without notice. Please always refer to the most recent release on www.hytronik.com/products/bluetooth technology ->Bluetooth Drivers
Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy