12 SPEED PRODUCTS DOORMATE Bicycle Garage Door Remote Control Instructions
- June 6, 2024
- 12 SPEED PRODUCTS
Table of Contents
For use with the listed garage door openers manufactured (TABLE BELOW). The garage door opener activates when the programmed button on the remote control is pressed. The remote control can activate a garage door opener.
Make sure the garage door opener has a working light bulb because it is a programming indicator.
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer or birth defects, or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Package includes:
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage
door:
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.
- Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
- ALWAYS keep the gate or garage door in sight until completely closed. NEVER permit anyone to cross the path of the moving gate or door.
PREPARE
Locate the LEARN BUTTON on the garage door opener.
NOTE: Your garage door opener may look different.
Locate the PROGRAM BUTTON on the remote control.
Locate your model of garage door opener in the table below to determine the number of button presses needed to program the remote control.
Number of button presses needed| Brand|
Type/Color of smart/Learn
---|---|---
1 time| Linear| MegaCode 1997-current 318 MHz
2 times| Chamberlain| Orange+red button 1997-2005 390MHz
3 times| Chamberlain| Purple button 1999-2009 315 MHz
4 times| Billion code| Green button 1993-1996 390 MHz
5 times| Genie Overhead Door| Intellicode 2005-current 315 MHz
6 times| Genie Overhead Door| Intellicode 2005-current 390 MHz
7 times| Chamberlain| Yellow button 2011- current 310 MHz
PROGRAMMING THE REMOTE
1. Using the provided safety pin, press and hold the PROGRAM BUTTON on the remote control until the LED on the front of the remote control turns on. This mode will last one minute.|
2. Press and release the REMOTE BUTTON the number of times that corresponds with the garage door opener type:
| 3. To exit programming mode, press PROGRAM BUTTON.
---|---|---
| 
|
4. Press and release the LEARN BUTTON to the garage door opener.| 5. Press the REMOTE BUTTON programmed in step 2 until the garage door opener lights flash or two clicks are heard.| 6. To test, press the REMOTE BUTTON on the remote control…
The Learn LED will light. Within 30 seconds…
| 
| 
INSTALLING REMOTE CONTROL ON HANDLEBAR
[1] Insert remote control into an unwrapped road bike handlebar end. Use a gentle twist motion that allows the remote control to be inserted fully and securely. Do not tap the remote control with a plastic mallet or similar tool when inserting it.
[2] Remove the release back sheet from the candle holders, and then install them on the handlebar. There are two handle holders that differ in shape. Attach (A) on the top.
[3] Attach (B) to the bottom and hold both tabs firmly to secure the adhesive onto the handlebar. If the double-sided tapes have diminished in adhesive strength after replacing the handle holders etc., cut some store-bought double-sided tape and replace them with a 15mm x 10mm stripe. Wrap the handlebar with handlebar tape, starting from the holder to the top of the handlebar to ensure the final security of the remote control.
HOW TO USE THE REMOTE CONTROL
Press and hold the REMOTE BUTTON down until the door or gate starts to move. Installations and conditions vary, contact an installing dealer for more information.
BATTERY
The LED(s) on your remote control will stop flashing when the battery is low and needs to be replaced. To replace the battery, open the case as shown. Unscrew the end cap counter-clockwise to expose the battery tray. Insert battery positive side up(+). Replace the battery with only an A27 battery. Dispose of the old battery properly.
NOTICE: To comply with FCC, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER-SERVICEABLE PARTS.
FCC Statement:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
WARNING
To prevent possible SERIOUS INJURY or DEATH:
- NEVER allow small children near batteries
- If the battery is swallowed, immediately notify the doctor.
- Replace ONLY with A27 battery
- DO NOT recharge, disassemble, heat above 212 F (100 C) or incinerate
WARRANTY
ONE YEAR LIMITED WARRANTY
Twelve Speed Products warrants to the first consumer purchaser of this product
that it is free from defects in materials and/or workmanship for a period of 1
year from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>