BEGA 51 052.4 Ceiling Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 51 052.4 Ceiling Luminaire
Product Information
| Product Name | Luminaire |
|---|---|
| Model Number | 51 052.4 |
| Lamp Type | Luminaire with screw base E27 |
| Lamp Output | Maximum 40W |
| Luminaire Efficiency | 57.3% |
| Safety | The installation and operation of this luminaire are subject to |
national safety regulations. Installation and commissioning must be
carried out by a qualified electrician. The manufacturer accepts no
liability for damage caused by improper use or installation. If
subsequent modifications are made to the luminaire, the person
responsible for these modifications shall be considered the
manufacturer.
Product Usage Instructions
Mounting
Before installing onto the ceiling, follow the steps below:
- Insert the luminaire mounting plate into the luminaire housing.
- Pass the mains supply cable through the grommet into the luminaire mounting plate.
- Fix the mounting plate inside the luminaire housing using enclosed or any other suitable fixing material on the mounting surface.
- Dismantle the mains supply cable by approximately 60mm.
- Pull silicone sleeves over the wires and make earth and electrical connections to the terminals.
- Insert the lamp.
Relamping
To replace the lamp, follow the steps below:
- Disconnect from the main supply.
- Unscrew the synthetic diffuser from the luminaire housing by turning it counter-clockwise.
- Change the lamp.
- Screw in the synthetic diffuser by turning it clockwise.
- If the synthetic diffuser is damaged, it must be replaced.
Spares
| LED Lamp | 13 592 15 000 |
|---|---|
| Synthetic Cover | 424 63 000 |
| Lampholder | 585 71 003 |
| Shield | 498 B12 |
DIMENSIONS
Instructions for use
Application
Ceiling luminaire · indoor luminaire impact resistant synthetic diffuser and
metal housing for non-glare light deflected downwards.
Product Description
- Ceiling luminaire »STUDIO LINE«
- Aluminium luminaire housing, finish Colour velvet black inside hue matt brass
- Metal luminaire mounting plate, finish Colour velvet black
- Impact resistant synthetic diffuser, white, with bayonet closure
- 2 mounting holes ø 5.5 mm
- Distance apart 180 mm
- 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@
- Connection terminal 2.5@
- Earth conductor connection
- Lampholder E 27
Safety class I
- – Safety mark
- – Conformity mark
- Weight: 0.95 kg
Safety
- The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Lamp
- Luminaire with screw base E 27
- Lamp output max. 40 W
- This product contains light source of energy efficiency class E
- Supplied lamp
- BEGA LED lamp 13592
- LED 12 W · 1400 lm · 3000 K
- Luminaire efficiency: 57.3%
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Installation
- Before installing onto the ceiling the luminaire mounting plate must be inserted into the luminaire housing.
- Thereby pass the mains supply cable through the grommet into luminaire mounting plate. Fix monting plate inside the luminaire housing with enclosed or any other suitable fixing material on to the mounting surface. Dismantle the mains supply cable approx. 60 mm.
- Pull silicone sleeves over the wires and make earth and electrical connection to the terminals. Insert lamp.
- In order to securely install the synthetic cover in the fitting, the top opening of the synthetic cover must be inserted into the luminaire housing at an angle.
- Make sure that at least one of the recesses in the edge of the synthetic cover matches the position of one of the lugs on the fitting – see drawing.
IMPORTANT:
- Turn the synthetic cover upwards into the fitting as far as it will go. Now secure the synthetic cover in the fitting by turning it clockwise.
- Only then is the synthetic cover held securely in place and resistant to vibration.
- The synthetic cover is removed by turning
- it anti-clockwise as far as it will go while simultaneously pushing the synthetic cover up against the luminaire fitting.
Cleaning · Maintenance
- Clean luminaire regularly with solvent-free cleansers from dirt.
Relamping
- Disconnect from main supply.
- Unscrew synthetic diffuser from luminaire housing by turning it counter-clockwise. Change the lamp.
- Screw in synthetic diffuser by turning it clockwise.
- A damaged synthetic diffuser must be replaced.
Spares
- LED lamp 3000K 13 592
- Synthetic cover 15 000 424
- Lampholder 63 000 585
- Shield 71 003 498 B12
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>