BEGA 31223 Wall Luminaire Instruction Manual

BEGA 31223 Wall Luminaire

Instructions for use

Application

• Wall luminaire made of copper and hand-blown crystal bubble glass.

• An annular shield which is positioned in the centre of the incandescent lamp prevents glare from the luminaire without affecting the brilliance of the crystal bubble glass.

• For many lighting tasks in or on buildings.

• Product description

• Luminaire made of copper

• Crystal bubble glass with screw neck

• Silicone gasket

• Wall mounting with a mounting plate made of stainless steel, Steel grade number 1.4301 Mounting plate with 2 fixing  holes ø 4.5 mm · 52 mm spacing 1 cable entry for mains supply cable
  up to ø 10,5 mm

• Connecting terminals 2.5@

• Earth conductor connection

• Lampholder E 27

• Safety class I

• Protection class IP 44

• Protected against granular foreign bodies  ≥ 1 mm and splash water  Impact strength IK06

• Protection against mechanical impacts < 1 joule

  • r – Safety mark
  • c  – Conformity mark
  • Weight: 2.2 kg

Lamp

• Luminaire with screw base E 27

• Lamp output max. 60 W

• This product contains light source of energy efficiency class E

• Supplied lamp

• BEGA LED lamp 13 583

• LED Retrofit 7 W · 805 lm · 3000 K

• Luminaire efficiency: 43%

• Additional BEGA LED lamps are available for this luminaire:
  13 585 LED 7 W · 805 lm · 3000 K dimmable

• Detailed technical and lighting data for the lamps can be found in the data sheets on our website.

Safety

• The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Installation

• Please use the protective gloves provided for the installation to prevent fingerprints on the luminaire.
• Screw glass out of the luminaire base.
• Undo screw of the wall box.
• Remove mounting plate from wall box.
• Lead the mains supply cable through the cable entry of the mounting plate.
• Note position of application of the mounting plate “arrow down”.
• Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
• It is absolutely essential to use the enclosed gaskets.
• Make earth conductor connection and make electrical connection.
• Note position of application of luminaire “arrow down”.
• Make earth conductor connection between luminaire and mounting plate.
• Place the luminaire housing on the mounting plate, adjust and tighten screw. Insert lamp.
• Slide glass with gasket over the lamp and screw into the luminaire.
• Make sure that the gasket is positioned correctly.

Relamping · Maintenance

• Disconnect the electrical installation.
• Open the luminaire and clean.
• Use only solvent-free cleaning agents. Change the lamp.
• Check the gasket and replace, if necessary. Close the luminaire.
• For cleaning, do not use high pressure cleaners.

Copper

• The luminaire parts made of solid copper are delivered with the metal’s natural surface colour.
• Time and weather factors create the natural patina characteristic for copper.

Spares

• Spare glass with gasket 11 002 745 43
• LED lamp 3000K 13 583
• Lampholder 63 000 355
• Gasket glass 83 000 722

CONTACT

• ADDRESS: BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden ·
• info@bega.com ·
• www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>