BEGA 33 327 Ceiling Wall Pillar Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 33 327 Ceiling Wall Pillar Luminaire
Instructions for use
Safety
Product description
Overvoltage protection
Installation
Cleaning · Maintenance
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 33 327 Ceiling Wall Pillar Luminaire

Instructions for use

BEGA-33-327-Ceiling-Wall-Pillar-Luminaire-FIG-1

Application
Shielded ceiling, wall and pillar luminaire with high protection class.
A luminaire made of aluminium alloy and impact resistant crystal glass with light diffusing structures.

Lamp

Module connected wattage 2.9 W
Luminaire connected wattage 4 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 55 °C

33 327 K3

Module designation LED-0444/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 550 lm
Luminaire luminous flux 240 lm
Luminaire luminous efficienc y 60 lm / W

33 327 K4

Module designation LED-0444/840
Colour temperature 4000 K
Colour rendering inde x CRI > 80
Module luminous flux 565 lm
Luminaire luminous flux 246 lm
Luminaire luminous efficiency 61,5 lm / W

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer

Product description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Crystal glass, white inside 2 mounting holes ø 4.3 mm
Distance apart 64 mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK06
Protection against mechanical impacts < 1 joule
r – Safety mark
c – Conformity mark
Weight: 1.4 kg
This product contains light sources of energy efficiency classes C

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at: www.bega.com.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo screws.
Remove frame and glass with gasket.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection.
Insert glass with gasket and frame.
Make sure that the gasket is positioned correctly.Tighten screws evenly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares