BEGA 24 736 Wall luminaire Applique Instructions
- June 12, 2024
- BEGA
Table of Contents
**BEGA 24 736 Wall luminaire Applique
**
Dimension
Application
Wall luminaire with single-sided light output for illumination and design
tasks in architecture.
The luminaire can be installed with the light distribution opening upwards or
downwards.
Product description
Luminaire made of aluminium alloy,
aluminium and stainless steel
BEGA Unidure® coating technology
Matt safety glass
Reflector surface made of pure aluminium
Mounting plate with 2 fixing
holes ø 4.5mm · 38 x 110mm spacing
2 cable entries for through-wiring of mains
supply cable ø 7-12mm
Connecting terminal 2.5@
with plug connection
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
BEGA Thermal Control®
Temporary thermal regulation to protect
temperature-sensitive components without
switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical
impacts < 1 joule
– Conformity mark
Weight: 1.2 kg
This product contains light sources of energy
efficiency classes C, D
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Lamp
Module connected wattage 3.9 W
Luminaire connected wattage 5 W
Rated temperature ta=25 °C
Ambient temperature ta max=60 °C
24 736K3
Module designation LED-1029/830
Colour temperature 3000 K
Colour rendering index CRI >80
Module luminous flux 645 lm
Luminaire luminous flux 485 lm
Luminaire luminous efficiency 97 lm/W
24 736K4
Module designation LED-1029/840
Colour temperature 4000 K
Colour rendering index CRI >80
Module luminous flux 685 lm
Luminaire luminous flux 515 lm
Luminaire luminous efficiency 103 lm/W
Light technique
Broad spread light distribution. Half beam angle 70°
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo hexagon socket head screws (wrench size 3mm) up to the stop and
disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Fix the mounting plate with enclosed or any other suitable fixing material
onto the mounting surface.
Make earth conductor connection and electrical connection to the connecting
terminal (plug connection).
Make earth conductor connection between luminaire housing and mounting plate.
Push plug into coupler as far as it will go.
Place luminaire housing onto the mounting plate and fix it.
Make sure that gasket is positioned correctly
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
LED power supply unit DEV-0450/350
LED module 3000 K LED-1029/830
LED module 4000 K LED-1029/840
Reflector 76 001 987
Gasket 83 002 073
Customers Support
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com · www.bega.com