BEGA 24 089 Ceiling Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 24 089 Ceiling Luminaire
Product Information
Product Usage Instructions:
Instructions for use
DIMENSION
Product Description
Safety
Installation
FEATURES
Cleaning Maintenance

BEGA 24 089 Ceiling Luminaire

BEGA-24-089-Ceiling-Luminaire-PRODUCT

Product Information

Product Description| Luminaire made of aluminium alloy, aluminium and stainless
steel. Matt safety glass. Silicone gasket. Reflector surface made
of pure aluminium.
---|---
Safety Class| Class I
Protection Class| IP65 (Dust-tight and protection against water jets)
Impact Strength| IK08
Weight| 1.6 kg
Energy Efficiency Class| C

Product Usage Instructions:

Installation:
Undo the screws and lift off the luminaire top.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
For digital control, please use the connecting terminal DA, DA. In case this terminal is not used, the luminaire will be operated at full light output.
Overvoltage Protection:

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against transients, it is recommended to use separate overvoltage protection components available on the website: www.bega.com.

Desiccant Pouch Placement:

In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.

Instructions for use

Application
Ceiling luminaire · Wallwasher
With asymmetrical light distribution for soft lighting effects without any harsh light cones on the illuminated wall surface.

DIMENSION

$BEGA-24-089-Ceiling-Luminaire-FIG- $1$$

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or white
Matt safety glass
Silicone gasket
Reflector surface made of pure aluminium
2 mounting holes ø 6 mm
Distance apart 140 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting terminal 2.5@ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-276 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK08
Protection against mechanical impacts < 5 joule
Safety mark
Conformity mark
Weight: 1.6 kg
This product contains light sources of energy efficiency class(es) C

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the screws and lift off the luminaire top. Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Make earth conductor connection between luminaire top and luminaire base.
Push plug into coupler as far as it will go. Make sure that gasket is positioned correctly. Install the luminaire top, press-on and tighten screws evenly.
It is imperative to observe that the earth conductor connection is not shut between the reflector and luminaire top.

FEATURES

Lamp

Module connected wattage 19.4 W
Luminaire connected wattage 22.1 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 30 °C

24 089 K3

Module designation LED-0896/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 3760 lm
Luminaire luminous flux 2841 lm
Luminaire luminous efficiency 128,6 lm / W

24 089 K4

Module designation LED-0896/840
Color temperature 4000 K
Color rendering index CRI > 80
Module luminous flux 3865 lm
Luminaire luminous flux 2920 lm
Luminaire luminous efficiency 132,1 lm / W

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares