BEGA 50067.2 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50067.2 Wall Luminaire
Product Information
Product Usage Instructions
Dimension
Instructions for use
Safety
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50067.2 Wall Luminaire

Product Information

Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against transients, etc., separate overvoltage protection components are recommended. They can be found on the manufacturer’s website at www.bega.com.
Lamp Module Connected Wattage: 15.2 W
Luminaire Connected Wattage: 19 W
Rated Temperature: 25°C
Ambient Temperature: 45°C
Module Designation: 4x LED-0626/930
Colour Temperature: 3000 K
Colour Rendering Index (CRI): >90
Module Luminous Flux: 2560 lm
Luminaire Luminous Flux: 1542 lm
Luminaire Luminous Efficiency: 81.2 lm/W
Spare Parts: Spare glass, LED power supply unit, LED module 3000 K, Gasket glass

Product Usage Instructions

To ensure safety and compliance with regulations, the installation and commissioning of this luminaire should only be carried out by a qualified electrician.
For additional protection against overvoltage and transients, it is recommended to use separate overvoltage protection components. These components can be found on the manufacturer’s website at www.bega.com.
Ensure that the lamp module connected wattage does not exceed 15.2 W and the luminaire connected wattage does not exceed 19 W.
The luminaire is designed to operate within a rated temperature of 25°C and an ambient temperature of 45°C. Ensure that these temperature limits are not exceeded during usage.
The module designation is 4x LED-0626/930 with a colour temperature of 3000 K and a colour rendering index (CRI) greater than 90. The module luminous flux is 2560 lm, and the luminaire luminous flux is 1542 lm with a luminous efficiency of 81.2 lm/W.
If replacement of the LED module is necessary, refer to the label in the luminaire for the designation of the LED module. BEGA replacement modules have matching light colour and light output. Qualified persons can use standard tools to replace the module. Disconnect the system, open the luminaire, and follow the installation instructions for the LED module. Replace any defective glass and close the luminaire securely.
If spare parts are required, the following items can be used: spare glass, LED power supply unit, LED module 3000 K, and gasket glass. Refer to the provided part numbers for ordering.

Dimension

BEGA-50067.2-Wall-Luminaire-fig-1

Instructions for use

Application
Free radiating wall luminaire · indoor luminaire with hand-blown three-ply opal glass for a soft and uniform light distribution. The elongated design of this wall luminaire particulary provides suitability for installation on pillars, columns and for the front surface of walls, as well as for recesses or profiles. The luminaire may be installed horizontally or vertically.
Product description
Metal luminaire housing,finish Stainless steel Hand-blown opal glass The electrical equipment can be hinged 2 mounting holes ø 6 mm Distance apart 230 mm Jointing sleeve with cable entry for mains supply cable up toø 14 mm, max. 5 x 1.5@ Connecting terminals 2.5@Earth conductor terminal LED power supply unit 220-240 V x 0/50-60 Hz DC 176-276 V During DC operation the LED power is reduced to 15 % DALI-controllable Basic insulation is provided between the mains and control cables BEGA Thermal Control® Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire Safety class I Protection class IP 65 Dust-tight and protection against water jets Impact strength IK03 Protection against mechanical impacts < 0.35 joule r – Safety mark c – Conformity mark Weight: 2.6 kg This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

BEGA-50067.2-Wall-Luminaire-fig-2

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Undo hexagon socket (wrench size 5) in the locking cap and remove it. The opal glass can now be hinged together with the electrical equipment to the front. Remove opal glass. Note position of application of the luminaire»arrow down«. Drill mounting holes into the mounting surface – spacing 230 mm and turn in enclosed or suitable fixing screws. For the electrical connection undo the screwconnection at the line connector and remove the terminal block. Make earth conductor connection and electrical connection. Make connection of the phase with the L marked, the neutral wire at the N marked and earth conductor at the PE marked connecting terminal.For digital actuation please use the two connecting terminals DA. If these terminals are not assigned, the luminaire will work with full light output. Bolt together both screw cable glands firmly. Hook luminaire into the fixing screws andtighten. Slide opal glass over the lamp and fasten with the locking cap. Make sure that the gaskets are positioned correctly.

Lamp
- Module connected wattage 15.2 W
- Luminaire connected wattage 19 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 45 °C
50 067.2 K3
- Module designation 4x LED-0626/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 2560 lm
- Luminaire luminous flux 1542 lm
- Luminaire luminous efficiency 81,2 lm / W

Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt. Defective glass must be replaced.

Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Defective glass must be replaced. Close the luminaire.