BEGA 24586 Wall Luminaire Instruction Manual

June 12, 2024
BEGA

BEGA-LOGO

BEGA 24586 Wall Luminaire

BEGA-24586-Wall-Luminaire

Product Information

Product Name: Wandleuchte Wall luminaire Applique

Model Number: 930

IP Rating: IP 65

Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage according to DIN EN 61547. Additional protection against transients is recommendedthrough separate overvoltage protection components.

Safety: The installation and operation of this luminaire must comply with national safety regulations. Only qualified electricians should carry out the installation and commissioning. The manufacturer is not liable for damage caused by improper use or installation.

Product Usage Instructions

  1. Installation:
    • Undo the hexagon socket head screws (wrench size 3 mm) and lift the mounting bar out of the luminaire housing.
    • Note the position of application of the mounting bar (wall side).
    • Lead the mains supply cable through the opening of the mountingbar.
    • Fix the mounting bar with the enclosed or other suitable fixing material onto the mounting surface. Ensure an even mounting surface.
  2. LED Module / Power Supply Replacement:
    • The designation of the LED module is noted on a label in the luminaire. BEGA replacement modules have the same light color andlight output as the original modules.
    • The LED module can be replaced by qualified individuals using standard tools.
    • Avoid touching the light output opening of the LED directly during relamping.
  3. Luminaire Specifications:
    • Lamp Module Connected Wattage: 34.8 W
    • Luminaire Connected Wattage: 39 W
    • Rated Temperature: 25°C
    • Ambient Temperature: 60°C max
  4. Module Specifications:
    • Module Designation: 3x LED-1204/830
    • Colour Temperature: 3000 K
    • Colour Rendering Index (CRI): >80
    • Module Luminous Flux: 6765 lm
    • Luminaire Luminous Flux: 3464 lm
    • Luminaire Luminous Efficiency: 88.8 lm/W

Dimension

BEGA-24586-Wall-Luminaire-FIG-1

Instructions for use

Application
Wall luminaire with light emission on one side and symmetrical light distribution to illuminatefaçade and wall surfaces. A luminaire that allows interesting illumination concepts individually, in rows or groups. The luminaire can be installed in any burning position.
Product Description
Luminaire made of aluminum and stainless steelBEGA Unidure® coating technology Safety glass with optical structure Reflector made of pure anodized aluminium Mounting bar with 2 elongated holes 7 mm width, 850 mm spacing Connection box with 2 cable entries for through-wiring of the mains supply cable ø 5-13 mm, max. 5×2,5@  Connecting terminals and earth conductor terminal 2,5@ LED power supply unit 220-240 V x 0/50-60 Hz DC 176-280 V During DC operation the LED power is reduced to 15 % DALI-controllable Basic insulation is provided between the mains and control cables BEGA Thermal Control® Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire Safety class I Protection class IP 65 Dust-tight and protection against water jets Impact strength IK06 Protection against mechanical impacts < 1 joule r – Safety mark c – Conformity mark Weight: 8.6 kg This product contains light sources of energy efficiency class(es) C
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Installation

Undo hexagon socket head screws (wrench size 3 mm) and lift the mounting bar out of luminaire housing. Note position of application of the mounting bar – wall side. Lead mains supply cable through the openingof the mounting bar. Fix mounting bar with enclosed or other suitable fixing material onto mounting surface. It is absolutely essential to have an even mounting surface.BEGA-24586-Wall-Luminaire-FIG-2

Use the supplied connection box to make the electrical connection (see illustration). Undo hexagon socket head screws (wrench size 3 mm) and open the connection box. Run the power connecting cable through the M20 cable gland and into the connection box. For through-wiring, the factory-fitted dummy\ plugs must be removed. Tighten the cable glands securely. Make the earth conductor connection and the electrical connection. Observe the correct configuration of the connecting cable. Connect the earth conductor to the green-yellow wire (PE), the live \ conductor to the brown wire (L) and the neutral conductor to the blue wire (N). The control cables are connected via the two DALI-labelled wires. If these wires are not assigned, the luminaire will work with full light output. Close the connection box. Make sure the gasket is properly located. Hang the luminaire housing in the mounting rail and screw it in place.
Please note:
Do not remove the desiccant bag from the luminaire housing. It is needed to remove residual moisture.
Replacing the LED module / Power supply unit
The designation of the LED module is noted on a label in the luminaire.The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.

BEGA-24586-Wall-Luminaire-FIG-3LED are high- quality electronic components! Please avoid touching the light output opening of the LED directly during relamping.
Unscrew the two hexagon socket screws (wrench size 3 mm) through the openings in the luminaire housing and remove the luminaires from the mounting rails. To open the connection box, unscrew the hexagon socket screws (wrench size 3 mm) and disconnect the electrical connection of the power connecting cable. To replace the LED module or power supply unit, remove the front housing cover (on the side of the cable entry). Loosen the hexagon socket screw (wrench size 3 mm) at the back of the luminaire housing and remove the front housing cover. Remove the earth conductor connection plug. To pull the module carrier out of the housing, unscrew the hexagon socket screw (wrench size 5 mm) and remove the terminal block. Carefully pull the reflector out of the housing. Pull out the module carrier until the connection terminals are exposed. Remove the connecting cable from the PSUterminals and pull out the module carrier entirely. Replace the PSU / LED module. Follow theinstallation instructions for the LED module. Install in reverse order. Push the reflector with anodised finish into the luminaire housing directed outwards. Make sure that the module carrier and housing are positioned correctly (see drawing Item A).
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.

  • Lamp
    • Module connected wattage 34.8 W
    • Luminaire connected wattage 39 W
    • Rated temperature ta = 25 °C
    • Ambient temperature ta max = 60 °C
  • 24 586 K3
    • Module designation 3x LED-1204/830
    • Colour temperature 3000 K
    • Colour rendering index CRI > 80
    • Module luminous flux 6765 lm
    • Luminaire luminous flux 3464 lm
    • Luminaire luminous efficiency 88,8 lm / W
  • 24 586 K4
    • Module designation 3x LED-1204/840
    • Colour temperature 4000 K
    • Colour rendering index CRI > 80
    • Module luminous flux 6960 lm
    • Luminaire luminous flux 3564 lm
    • Luminaire luminous efficiency 91,4 lm / W
  • Spares
    • Spare glass with frame graphite 25 000 133
    • Spare glass with frame silver 25 000 134
    • Resistor 61 001 754
    • LED power supply unit DEV-0415/700
    • LED module 3000 K LED-1204/830
    • LED module 4000 K LED-1204/840
    • Reflector 76 002 022
    • Gasket cover 83 001 830
    • Gasket housing 83 002 080

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals