BEGA 67719 Indoor Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
Wall luminaire for indoor use
67719 Indoor Wall Luminaire
Instruction Manual
67719 Indoor Wall Luminaire
Application
Wall luminaire · indoor luminaire made of handblown opaque crystal glass and metal housing, for all lighting tasks in interior applications. They are ideal for places where a soft and uniform lighting distribution is required.
Product description
Metal housing, finish Colour white Hand-blown opaque crystal glass, with
crewneck and gasket 2 mounting holes ø 5.5 mm Distance apart 240 mm 2 cable
entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@
Connecting terminal 2.5@ with plug connection Earth conductor connection
2-pole connecting terminal for digital control LED power supply unit 220-240 V
0/50-60 Hz DC 170-276 V DALI-controllable Number of DALI addresses: 1 Basic
insulation is provided between the mains and control cables BEGA Thermal
Control® Temporary thermal regulation to protect temperature-sensitive
components without switching off the luminaire Safety class I Protection class
IP 44 Protected against granular foreign bodies ≥ 1 mm and splash water Impact
strength IK06 Protection against mechanical impacts < 1 joule
– Safety mark
** – Conformity mark
Weight:** 6.2 kg
This product contains light sources of energy efficiency class(es) D, E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage| 25.3 W
Luminaire connected wattage| 28.8 W
Rated temperature| ta = 25 °C
Ambient temperature| ta max = 45 °C
67 719 K3
Module designation| LED-0570/930
Colour temperature| 3000 K
Colour rendering index| CRI > 90
Module luminous flux| 3615 lm
Luminaire luminous flux| 2477 lm
Luminaire luminous efficiency| 86 lm / W
67 719 K4
Module designation| LED-0570/940
Colour temperature| 4000 K
Colour rendering index| CRI > 90
Module luminous flux| 3760 lm
Luminaire luminous flux| 2575 lm
Luminaire luminous efficiency| 89,4 lm / W
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or revamping.
Disassemble LED module.
Loosen LED-connection and earth connection (plug connection).
Lead mains supply cable through the cable entry into the luminaire housing.
Fix the luminaire housing with enclosed or any other suitable fixing material
onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make earth and electrical connection to the terminal.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
Make earth connection between LED module and luminaire housing (plug
connection).
Push LED-plugs into couplers as far as it will go.
Assemble LED module.
Tighten the screws evenly (max. 0,8 Nm).
Please observe that the LED module is not damaged mechanically.
ATTENTION!
Make sure that the start of thread (glass) corresponds exactly with the start
of thread (luminaire housing).
Fix glass to the luminaire housing by turning it clockwise.
Make sure that the gasket is seated correctly.
Replacement of the LED module ·
Maintenance
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect the system.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Please follow the installation instructions for the LED module.
Screw in glass by turning it clockwise as far as it will go.
A broken glass must be replaced.
Spares
| Spare glass | 11 002 948 47R G |
|---|---|
| LED power supply unit | DEV-0391/850 |
| LED module 3000 K | LED-0570/930 |
| LED module 4000 K | LED-0570/940 |
| Gasket glass | 83 001 338 |
BEGA Gantenbrink- Leucite KG
Postfach 31 60 · 58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>