BEGA 50300 LED Ceiling and Wall Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50300 LED Ceiling and Wall Luminaire for Indoor Use
Dimension
Instructions for use
Safety
Replacement of the LED unit
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50300 LED Ceiling and Wall Luminaire for Indoor Use

Dimension

BEGA-50300-LED-Ceiling-and-Wall-Luminaire-for-Indoor-Use-
FIG-1

Instructions for use

Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.
Product description
Metal housing, finish Colour white Hand-blown opal glass, satin matt 2 mounting holes ø 5.5 mm Distance apart 180 mm 2 cable entries for through- wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@ Earth conductor connection LED power supply unit 220-240 V y 50-60 Hz BEGA Thermal Switch® Temporary thermal shutdown to protect temperature-sensitive components Safety class I Impact strength IK05Protection against mechanicalimpacts < 0.7 jouler – Safety mark c – Conformity mark Weight: 2.0 kgThis product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp
- Module connected wattage 7.6 W
- Luminaire connected wattage 9.5 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 45 °C
50 300 K27
- Colour temperature 2700 K
- Colour rendering index CRI > 90
- Module luminous flux 1225 lm
- Luminaire luminous flux 942 lm
- Luminaire luminous efficiency 99,2 lm / W
50 300 K3
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 1280 lm
- Luminaire luminous flux 957 lm
- Luminaire luminous efficiency 100,7 lm / W

Notice prior to installation:
Luminaire with trim frame The luminaire housing must be inserted in the trim frame (accessory) before it is mounted onto the mounting surface. Make sure that the two openings in the trimframe coincide with the positions of the grub screws of the luminaire housing.
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Lead mains supply cable through the cable entry into the luminaire housing. Fix the luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.It is imperative to use the enclosed gaskets.Make earth and electrical connection to the terminal. BEGA-50300-LED-Ceiling-and-Wall-
Luminaire-for-Indoor-Use-FIG-2

Position the glass over the luminaire housing so that the retaining springs fit into the two recesses in the raised edge of the glass. Press the glass against the retaining springs at a flat angle as far as it will go and push it into the luminaire housing (see drawing). Gentle pressure on the glass will fix it in theluminaire housing through the three lobes on the opposite side. BEGA-50300-LED-Ceiling-and-Wall-Luminaire-for-Indoor-Use-
FIG-3
IMPORTANT:
If the luminaire is to be installed on the ceiling, it is essential that the two grub screws (Allen screws) should be screwed with gentle pressure against the retaining springs.In this way, the glass is held securely in place and is resistant to vibration.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Opening the luminaire
Unscrew the two grub screws (Allen screws) of the luminaire housing as far as they will go. A recess (identifiable by touch) in the edge of the glass indicates the direction from which the luminaire glass must be pressed against the spring pressure of the glass retaining springs in order to release it from the luminaire housing. Pull the glass away from the luminaire housing against the holding force of the retainingsprings and remove it.

Replacement of the LED unit

The designation of the LED unit is noted on a label in the luminaire. The light colour and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can bereplaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Replace the LED unit. Close the luminaire. A damaged glass must be replaced.
Accessory · Trim frames
For this luminaire metal trim frames in 3 enamelsurfaces are optional available.Trim frames are accessories and must be ordered separately.