BEGA 89764 Ceiling and Wall Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 89764 Ceiling and Wall Luminaire for Indoor Use
Product Information
Product Usage Instructions
Dimension
Instructions for use
Safety
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 89764 Ceiling and Wall Luminaire for Indoor Use

Product Information

The product is a luminaire with an IP rating of 44. It has a bottom design and operates at 85 volts. The luminaire has a 49% efficiency rate. For detailed technical and lighting data, refer to the data sheets available on the manufacturer’s website. The product also has spare parts available, including spare glass, LED lamps in both 2700 K and 3000 K variants, a lampholder, and a reflector.

Product Usage Instructions

Safety: The installation and operation of this luminaire must adhere to national safety regulations. Only a qualified electrician should carry out the installation and commissioning process. The manufacturer will not be liable for any damages caused by improper use or installation. If any modifications are made to the luminaire, the person responsible for these modifications will be considered the manufacturer.

Dimension

BEGA-89764-Ceiling-and-Wall-Luminaire-for-Indoor-Use-
fig-1

Instructions for use

Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

Lamp
- Luminaire with screw base E 27
- Lamp output max. 2 × 60 W
- This product contains light sources of energy efficiency class E
- Supplied lamp
- 2 × BEGA LED lamp 13548
- LED Retrofit 7 W · 805 lm · 2700 K
- Supplied lamp
- 2 × BEGA LED lamp 13586
- LED Retrofit 7 W · 805 lm · 3000 K
Luminaire efficiency: 49%

Detailed technical and lighting data for the lamps can be found in the data sheets on ourwebsite.
Product description
Metal housing, finish colour white Hand-blown opal glass, satin matt, with sliding-bolt closure 2 mounting holes ø 5.5 mm Distance apart 200 mm 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@ Earth conductor connection Lampholder E 27 Safety class I Protection class IP 44 Protected against granular foreign bodies ≥ 1 mm and splash water Impact strength IK05 Protection against mechanical impacts < 0.7 joule r – Safety markc – Conformity mark Weight: 2.0 kg

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible forthese modifications shall be considered the manufacturer.
Installation
Pass the mains supply cable through the base plate. Notice position of the application »arrow down« when installed at the wall. Fix base of the luminaire with enclosed or any other suitable fixing material on to the mounting surface. It is imperative to use the enclosed gaskets. Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection. Insert lamps. The sliding-bolt closure provides a safe and vibration-resistant holding of glass. Place glass to the base plate and observe that the holding spring bolts fit into the notches of the glass. Insert the opal glass into the luminaire base with sliding bolt glass closure and turn the glass clockwise until it is locked.To release the glass from the base plate, turn it counterclockwise.
Relamping · Maintenance
Disconnect the electrical installation. To release the glass from the housing, turn it counterclockwise. Clean luminaire and glass. Use only solvent-free cleansers. Change the lamp. The sliding-bolt closure provides a safe and vibration-resistant holding of glass. Place glass to the housing and observe thatthe holding spring bolts fit into the notches of the glass.Turn the glass clockwise until it is locked.