AJAX DoorProtect Wireless Magnetic Door Detector User Guide

AJAX DoorProtect Wireless Magnetic Door Detector

DoorProtect is a wireless door and window opening detector, equipped with a sealed contact reed relay designed for processing more than one million openings. It has a socket for connecting an external detector. DoorProtect is connected to the Ajax security system via the protected Jeweller protocol, with an effective communication range of up to 1,200 meters without obstacles. It can operate up to 7 years from a bundled battery and is designed for use indoors.

IMPORTANT:
This Quick Start Guide contains general information about DoorProtect. Before using the device, we recommend to reviewing the User Manual on the website: ajax.systems/support/devices/doorprotect.

FUNCTIONAL ELEMENTS

1. DoorProtect.
2. Big magnet.
3. Small magnet.
4. Light indicator.
5. SmartBracket attachment panel (perforated part is required for actuating the tamper in case of any attempt to tear off the detector from the surface).
6. External detector connection socket.
7. QR code.
8. Device switch.
9. Tamper button.

LOCATION SELECTION

When selecting an installation location for DoorProtect, take into account any obstacles impairing the radio signal transmission.

Do not install the detector:

1. Outside the premises (outdoors).
2. Nearby any metal objects and mirrors causing radio signal attenuation or screening it.
3. Within any premises with the temperature and humidity beyond the range of permissible limits.

Prior to the attachment of the detector to a surface with screws, please perform a signal strength test in the Ajax Security System application for at least a minute. This will demonstrate communication quality between the detector and the hub and ensures proper installation place selection.

The detector is equipped with two magnets – small and big, with the magnet operation ranges of 1 cm and 2 cm accordingly. The magnet is attached to the moving part of the door (window) to the right of the detector. If necessary, the detector may be positioned horizontally.

MOUNTING THE DEVICE

1. Fix the SmartBracket attachment panels of the detector and magnet with bundled screws or other no less reliable attachment hardware.
2. Put the detector on the panel – a single blink of the light indicator will confirm that the tamper has been actuated.
3. Fix the magnet on the attachment.

CONNECTION AND SETTING UP

The detector is connected to the hub and set up via the Ajax Security system mobile application. To establish a connection please locate the detector and the hub within the communication range and follow the device adding procedure. A wire detector with an NC type of contact may be connected to DoorProtect using an outside-mounted terminal clamp. To lead out the wire from the DoorProtect body, break out the plug.

Before using the external detector connected to the terminal clamp, activate it in the DoorProtect settings. To connect the detector to a third-party security central unit using the Ajax uartBridge or Ajax ocBridge Plus integration module, follow the recommendations in the user manual of the respective device. If the detector is located in a room requiring 24-hour control, activate the “Always active” mode – DoorProtect will be actuated in case of opening, even if the system is not in the arming mode.

IMPORTANT INFОRMATION

This product can be used across all EU member states. This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out.

CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

TECH SPECIFICATIONS

• Detector actuation threshold 1 cm (small magnet) 2 cm (big magnet)
• Anti-tamper switch Yes
• Frequency band 868.0-868.6 mHz
• Maximum RF output power Up to 20 mW
• Modulation FM
• Radio signal Up to 1,200 m (any obstacles absent)
• Socket for connecting wire detectors Yes, NC
• Power supply 1 battery CR123A, 3 V
• Battery life Up to 7 years
• Operating temperature range From 0°С to +50°С
• Operating humidity Up to 80%
• Dimensions Ø20х90 mm
• Weight 29 g

COMPLETE SET

1. DoorProtect.
2. Battery CR123A (pre-installed).
3. Big magnet.
4. Small magnet.
5. Outside-mounted terminal clamp.
6. Installation kit.
7. Quick Start Guide.

WARRANTY

The warranty for the Ajax Systems Inc. devices is valid for 2 years after the purchase and does not apply to the supplied battery. If the device does not work correctly, you should first contact the support service—in half of the cases, technical issues can be solved remotely! The full text of the warranty is available on the website: ajax.systems/warranty.

User Agreement:
ajax.systems/end-user-agreement

Technical support:
support@ajax.systems.

Manufacturer: Research and Production Enterprise LLC Address: Sklyarenko 5, Kyiv, 04073, Ukraine By request of Ajax Systems Inc. www.ajax.systems.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>