BEGA 51 066.1 Track Zoom Spotlight for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
Technical amendments reserved
Track zoom spotlight for indoor use
Instructions for use
Application
Track zoom spotlight · Indoor luminaire with adapter for 3-phase EUROSTANDARD
PLUS® track systems. The spotlight’s optical system can be swivelled and
rotated. Symmetrical light distribution. To change the light distribution,
optical filters are available as accessory parts. Changing the half beam angle
between 14° and 52° by twisting the lens unit.
Product description
Track zoom spotlight with adapter Cast aluminium luminaire housing, finish
Colour velvet white, Polycarbonate track adapter with integrated LED power
supply unit Optical lens made of silicate glass Adjustable metal adapter ring
with PMMA lens combination and integrated optical filter. LED power supply
unit 220-240 V ∼ 50/60 Hz DALI-controllable umber of DALI addresses: 1 Basic
insulation is provided between the mains and control cables Safety class II
– Conformity mark Weight: 0.7 kg This product contains light sources of energy
efficiency class(es) E, F
Lamp
| Module connected wattage | 12.8 W |
|---|---|
| Luminaire connected wattage | 15 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 55 °C |
51 066.1 K3
| Module designation | LED-1218/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1450 lm |
| Luminaire luminous flux | 667 lm |
| Luminaire luminous efficiency | 44,5 lm / W |
51 066.1 K4
| Module designation | LED-1218/940 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1540 lm |
| Luminaire luminous flux | 708 lm |
| Luminaire luminous efficiency | 47,2 lm / W |
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.
Light technique
Track spot · surface washer with adjustable optical system.
Optical system 0-340° swivel-mounted and ± 310° infinitely rotatable around
the vertical luminaire axis.
Symmetrical light distribution.
Changing the half beam angle between 14° and 52° by twisting the lens unit.
The symmetrical light cone can be changed to a flat beam, symmetrically
diffuse or asymmetrical light distribution for special lighting applications
by replacing the optical filter (standard) – accessoires.
For flat beam light distribution:
Optical filter 13 291 For symmetrically diffuse light distribution: Optical
filter 13 293
For asymmetrical light distribution: Optical filter 13 292
| standard
---|---
| flat beam
| symmetrically diffuse
| asymmetrical
The light cone can be adjusted by ±360° by turning the adapter ring with
optical filter.
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
The track zoom spotlight with adapter is ready for use in 3-phase
EUROSTANDARD-PLUS® track systems.
No tools are required to attach it to the track.
IMPORTANT:
Ensure that the adapter’s two lateral stays are located on the same side as
the matching guide profile of the track before installing the adapter in the
3-phase EUROSTANDARDPLUS® track system.
To select the phase ( 1 2 3 ) the turning knob on the rear side of the adapter
has to be operated accordingly. 
Place the surface washer adapter flush on the conductor rail in the desired
position.
Push the two fixing levers on the underside of the adapter to the right until
they click into their end position.
Set the desired LED beam direction by turning and tilting the luminaire
housing.
Please note: One of the two cams on the outer adjustment ring of the optical
lens unit is marked.
The desired half beam angle can be set between 14° and 52° using this cam
marking by turning the adjustment ring.
Move the two fixing levers in opposite directions until they disengage to
unlock the adapter.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified personnel using standard tools.
Disconnect the system from the mains.
IMPORTANT: Before disassembling the reflector with the optical lens unit,
the marked cam on the adjustment ring must be turned to the 15° position.
Grasp the internal adapter ring with optical filter by one of its metal tabs
and pull it out of the recess in the luminaire housing against the magnetic
resistance.
Remove the trim ring from the zoom spotlight housing by turning it anti-
clockwise.
Remove the reflector with optical lens unit from the housing.
Remove the LED module. Install the replacement LED module.
Please follow the installation instructions for the new LED module.
Replace the reflector in the luminaire housing.
IMPORTANT: The reflector is installed correctly once the two recesses in
the rear centring disc of the reflector fit over the two bolts on the side of
the LED module.
Ensure that the marked cam on the adjustment ring is pointing in the direction
of the spotlight’s joint axis.
Place the trim ring with scale on the luminaire housing and tighten clockwise.
Please note: The trim ring is only correctly mounted when the 15° position
corresponds to the position of the marked cam.
Reinsert the adapter ring with optical filter into the housing of the zoom
spotlight.
The magnetic housing recess allows the adapter ring to lock precisely into
place.
If the disc combination of the adapter ring with optical filter is defective,
it must be replaced.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Accessories · Optical filters
13 291 flat beam
13 293 symmetrical, diffuse
13 292 asymmetrical
For the accessories a separate instructions for use can be provided upon
request.
Spares
| Trim ring | 20 000 106 B7 |
|---|---|
| LED power supply unit | DEV-0437/350i |
| LED module 3000 K | LED-1218/930 |
| LED module 4000 K | LED-1218/940 |
| Lens unit | 75 004 801 |
| Adapter ring with dispersing filter | 75 004 848 |
51 066.1
BEGA Gantenbrink-Leuchten KG ·
Postfach 31 60 ·
58689 Menden ·
info@bega.com ·
www.bega.com
Documents / Resources
| BEGA
51 066.1 Track Zoom Spotlight for Indoor
Use
[pdf] Instruction Manual
51 066.1 Track Zoom Spotlight for Indoor Use, 51 066.1, Track Zoom Spotlight
for Indoor Use, Track Zoom Spotlight, Zoom Spotlight, Spotlight
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>