BEGA 50656 Ceiling and Wall Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50656 Ceiling and Wall Luminaire for Indoor
Instructions for use
Product Description
Safety
Overvoltage protection
Installation
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50656 Ceiling and Wall Luminaire for Indoor

Product Information

Product Description: This luminaire is a lighting fixture that requires installation and operation according to national safety regulations. It should only be installed and commissioned by a qualified electrician.
Overvoltage Protection: The luminaire is equipped with electronic components that are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage
protection components available on the manufacturer’s website.
Lamp Module Connected Wattage: 22.4 W
Luminaire Connected Wattage: Not specified
Rated Temperature: Not specified
Ambient Temperature: Not specified
Module Designation: 4x LED-0263/927
Color Temperature: 2700 K
Colour Rendering Index (CRI): >90
Module Luminous Flux: 3480 lm
Luminaire Luminous Flux: 2480 lm
Luminaire Luminous Efficiency: 100.8 lm/W

Product Usage Instructions

Ensure that the luminaire is installed and operated according to national safety regulations. Only a qualified electrician should carry out the installation and commissioning.
If you need additional protection against overvoltage or transients, consider using separate overvoltage protection components available on the manufacturer’s website.
The lamp module connected wattage is 22.4 W. Please ensure that the luminaire is operated within the specified wattage limits.
The module designation is 4x LED-0263/927 with a color temperature of 2700 K. This information is useful for replacement or compatibility purposes.
The luminaire provides a color rendering index (CRI) of over 90, indicating good color rendition. This is important for accurate color perception.
The module luminous flux is 3480 lm, while the luminaire luminous flux is 2480 lm. These values indicate the amount of visible light emitted by the luminaire.
The luminaire luminous efficiency is 100.8 lm/W, which represents the ratio of luminous flux to power consumption. Higher values indicate greater energy efficiency.

Ceiling and wall luminaire for indoor use

BEGA-50656-Ceiling-and-Wall-Luminaire-for-Indoor-fig-1

Instructions for use

Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt, and aluminum alloy housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

Product Description

Luminaire made of aluminum alloy

Finish Colour white
Hand-blown opal glass, satin matt, with sliding-bolt closure 2 mounting holes ø 5.5 mm

Distance apart 230 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@ Connection terminal 2.5@

Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 196-250 V

DALI-controllable
Basic insulation is provided between the mains and control cables

BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire

Safety class I
Protection class IP 44 Protected against granular foreign bodies ≥ 1 mm and splash water

Impact strength IK07

Protection against mechanical
impacts < 2 joule
r – Safety mark
c – Conformity mark
Weight: 3.4 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage 22.4 W
Luminaire connected wattage 24.6 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 45 °C

50 656 K27

Module designation 4x LED-0263/927
Color temperature 2700 K
Color rendering index CRI > 90
Module luminous flux 3480 lm
Luminaire luminous flux 2480 lm
Luminaire luminous efficiency 100,8 lm / W

50 656 K3

Module designation 4x LED-0263/930
Color temperature 3000 K
Color rendering index CRI > 90
Module luminous flux 3520 lm
Luminaire luminous flux 2509 lm
Luminaire luminous efficiency 102 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Lead mains supply cable through the cable entry into the luminaire housing. Fix the luminaire housing with enclosed or any other suitable fixing material onto the mounting surface. It is imperative to use the enclosed gaskets. Make an earth conductor connection. Push silicone sleeves over the lines and make an electrical connection. For digital control please use the connecting terminal DA, DA. In case this terminal is not used the luminaire will be operated at full light output. Insert the opal glass into the luminaire housing with sliding bolt glass closure and turn the glass clockwise up to the stop. Place glass to the luminaire housing and observe that the holding spring bolts fit into the notches of the glass. Turn the glass clockwise until it is locked. Thus, you reach a safe and vibration-resistant holding of the glass. To release the glass from the luminaire housing, turn it counterclockwise. Replacement of the LED module ·

Maintenance
The designation of the LED module is noted on a label in the luminaire. The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system. Unscrew the glass from the luminaire housing by turning it counterclockwise. Clean glass and luminaire regularly with solvent-free cleansers from dirt. Please follow the installation instructions for the LED module. Screw in the glass by turning it clockwise as far as it will go. A broken glass must be replaced.