BEGA 50496k27 Ceiling And Wall Luminaire For Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50496k27 Ceiling And Wall Luminaire For Indoor Use
DIMENSION
Product Information
- Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning should only be done by a qualified electrician. The manufacturer is not liable for damage caused by improper use or installation.
- Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. Separate overvoltage protection components are recommended for additional protection.
- Lamp Information :
- Module connected wattage: 7.6 W
- Luminaire connected wattage: 9.3 W
- Rated temperature: 25°C
- Ambient temperature: 45°C
- Module Designation: 2x LED-0544/927
- Colour temperature: 2700 K
- Colour rendering index (CRI): > 90
- Module luminous flux: 1240 lm
- Luminaire luminous flux: 904 lm
- Luminaire luminous efficiency: 97.2 lm/W
- Module Designation: 2x LED-0544/930
- Colour temperature: 3000 K
- Colour rendering index (CRI): > 90
- Module luminous flux: 1280 lm
- Luminaire luminous flux: 934 lm
- Luminaire luminous efficiency: 100.4 lm/W
Product Usage Instructions
- Installation
- Lead the mains supply cable through the cable entry into the luminaire back housing.
- Fix the luminaire base with the enclosed or any other suitable fixing material onto the mounting surface. Ensure to use the gasket rings supplied.
- Make the earth conductor connection.
- Push silicone sleeves over the lines and make the electrical connection.
- Snap the opal glass into the lower spring clips, centralize, and push into the upper spring clips.
- Replacement of the LED Module:
- The designation of the LED module is noted on a label in the luminaire.
- The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified persons using standard tools.
- Disconnect the system and open the luminaire.
- Please follow the installation instructions for the LED module.
- Defective glass must be replaced.
- Close the luminaire.
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass,
satin matt and aluminium alloy housing, for all lighting tasks. They are ideal
for places where a soft and uniform lighting distribution is required.
Luminaire with a high protection class.
Product description
- Luminaire made of aluminium alloy and stainless steel, finish Colour white
- Hand-blown opal glass, satin matt 2 mounting holes ø 5 mm
- Distance apart 255 mm 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@
- Earth conductor connection
- LED power supply unit 220-240 V x 0/50-60 Hz
- DC 176-280 V
- BEGA Thermal Switch®
- Temporary thermal shutdown to protect temperature-sensitive components
- Safety class I
- Protection class IP 44
- Protected against granular foreign bodies ≥ 1 mm and splash water
- Impact strength IK04
- Protection against mechanical impacts < 0.5 joule
- r – Safety mark
- c – Conformity mark
- Weight: 2.5 kg
- This product contains light sources of energy efficiency class(es) D
Safety
- The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at www.bega.com.
50 496 K27
- Module designation 2x LED-0544/927
- Colour temperature 2700 K
- Colour rendering index CRI > 90
- Module luminous flux 1240 lm
- Luminaire luminous flux 904 lm
- Luminaire luminous efficiency 97,2 lm / W
50 496 K3
- Module designation 2x LED-0544/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 1280 lm
- Luminaire luminous flux 934 lm
- Luminaire luminous efficiency 100,4 lm / W
Installation
- Lead the mains supply cable through the cable entry into the luminaire back housing.
- Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
- Be sure to use the gasket rings supplied. Make earth conductor connection.
- Push silicone sleeves over the lines and make electrical connection.
- Snap the opal glass into the lower spring clips, centralise and push into the upper spring clips.
Cleaning Maintenance
- Clean luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified persons using standard tools.
- Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
- Defective glass must be replaced.
- Close the luminaire.
Spares
- Spare glass 11 002 172 .0R G
- LED power supply unit DEV-0136/350
- LED module 2700 K LED-0544/927
- LED module 3000 K LED-0544/930
CONTACT
- ADDRESS: BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden ·
- info@bega.com ·
- www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>