MEEC TOOLS 011254 Mitre Saw Instruction Manual

: June 4, 2024
: MEEC TOOLS

MEEC TOOLS 011254 Mitre Saw

SAFETY INSTRUCTIONS

WARNING
Read all warnings, safety instructions and other instructions. Failure to follow all the instructions and safety instructions can result in the risk of electric shock fire and/or serious personal injury. ‘Save these instructions and safety instructions for future reference’.

WORKAREA

Keep the work area clean and well l it. Dark and cluttered work areas increase
The risk of accidents and injuries.
Do not use power tools in explosive environments, such as in the vicinity of flammable liquids, gas or dust. Power tools produce sparks that can ignite dust and fumes.
Keep children and onlookers at a safe distance when using power tools.
You can lose control of the tool if you are distracted.

ELECTRICAL SAFETY

The plug on the power tool must match the power point. Never modify the plug in any way. Never use an adapter with earthed power tools. Unmodified plugs and matching outlets reduce the risk of electric shock.
Avoid body contact with earthed surfaces such as pipes, radiators, cookers and refrigerators. There is an increased risk of electric shock if your body is earthed.
Do not expose power tools to rain or moisture. There is a greater risk of electric shock if water gets into a power tool.
Be careful with the power cord. Never use the power cord to carry or pull the tool, or to pull out the plug from the power point. Keep the power cord away from heat, oil, sharp edges and moving parts. Damaged or tangled power cords increase the risk of electric shock.
If using the tool outdoors, only use an extension cord approved for outdoor use. Cords intended for outdoor use reduce the
risk of electric shock.
If it is absolutely necessary to use power tools in damp conditions, use a mains connection protected by a residual current device (RDC). Using an RCD reduces the risk of electric shock.

PERSONAL SAFETY

Stay alert. Pay attention to what you are doing, and use your common sense when working with power tools. Never use power tools if you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when using a power tool can result in serious personal injury.
Use personal safety equipment. Depending on the type of tool and how it is used, safety equipment such as dust masks, non-slip safety shoes, safety helmets and ear protection reduce the risk of personal injury.
Avoid accidental starting. Make sure the power switch is in the OFF position before inserting the battery or lifting/carrying the tool. Carrying a power tool with your finger on the switch, or connecting a tool to the mains when the switch is in the ON position, increases the risk of accidents and injuries.
Remove adjuster keys/spanners before switching on the power tool. Spanners or the like that are left in a rotating part of the tool can cause personal injury.
Do not overreach. Always maintain a firm footing and good balance. This ensures better control over the power tool in unexpected situations.
Wear suitable clothing. Do not wear loose-fitting clothing or jewelry.
Keep your hair, clothing and gloves away from moving parts. Loose-fitting clothing, 1ewellery and long hair can get caught in moving parts.
If dust extraction and dust collection equipment is available, this should be connected and used correctly. The use of such devices can reduce the risk of dust-related problems.
Do not allow the fact that you are used to working with similar tools cause you to become over-confident and to disregard the safety instructions for the tool. Remember that a fraction of a second of inattention or negligence can result in serious personal injury.

USING AND LOOKING AFTER POWER TOOLS

Do not force the power tool. Use the correct power tool for the planned work. The tool does the job better and safer when used at the rate for which it was designed.
Do not use the tool if it cannot be switched on and off with the power switch. Power tools that cannot be controlled with the power switch are dangerous and must be repaired.
Pull out the plug and/or remove the battery before making any adjustments, changing accessories or putting the power tool away. These safety precautions reduce the risk of accidently starting the power tool.
Store power tools out of the reach of children when not in use. Never allow children, or anyone who is unfamiliar with the power tool and these instructions, to use the tool. Power tools are dangerous if used by inexperienced persons.
Keep the power tool properly maintained. Check that moving parts are properly adjusted and do not jam, and that no parts are incorrectly fitted or damaged. Check for other factors that could affect functionality. If the power tool is damaged, it must be repaired before being used again. Many acc idents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
Use the power tool, accessories and bits etc., in accordance with these instructions, taking into account the actual working conditions and the work that is to be done. It can be dangerous to use power tools for purposes other than those for which they are intended to be used.
Keep handles and grips clean, dry and free from oil and grease. Greasy handles and grips make it difficult to hold the tool.

SERVICE

The power tool must only be serviced by qualified personnel using identical spare parts. This will ensure that the power tool remains safe to use.

SPECIAL SAFETY INSTRUCTIONS FOR MITRE SAWS

All the warning symbols on the power tool must be clearly visible.
Put nothing on top of the tool. If the tool tips over or if you touch the saw blade this can lead to serious injury.
Check that the blade guard lies working properly and can move free y. Neve clamp the guard open.
Never clear away pieces of wood or sawdust from the saw while it is running. Put the saw arm in its rest posit ion and switch off the tool with the power switch.
Only apply the saw blade against the work piece when the saw is running. otherwise there is a risk of kickback if the blade jams in the workpiece.
Keep the handles clean, dry and free from oil and grease. Greasy or oily handles are slippery and can cause you to lose control. Remove tools and sawdust from the surface of the workspace on the power tool before sawing. On ly the workpiece should be there. Small pieces of wood and other objects that come into contact WITH the rotating blade can be thrown towards the operator at high speed.
Remove sawdust and other debris from the floor. You can slip on it or stumble.
Always firmly secure the workpiece. It is safer to secure the workpiece with a clamp than to hold it with your hand.
Do not saw workpieces that are not firmly secured. Otherwise your hand will come too near the rotating saw blade.
Only use the power tool for the type of material it is intended for. Otherwise it can overheat.
If the blade fastens, switch off the tool and hold the workpiece firmly until the blade has stopped rotating. To avoid kickback, do not attempt to loosen the workpiece before the blade has stopped. Find out why the blade has stuck and rectify the problem before using the tool again.
Never use blunt, cracked, bent or damaged blades. Blades with blunt or skew teeth result in narrow cuts. This increases the friction, the risk of the blade getting stuck and the risk of kickback.
Always use saw blades of the right size and with the right mounting hole (e.g. star-shaped or round). Blades that do not fit properly on the saw quickly lose their roundness and become difficult to control. Never use high-speed steel (HSS) blades. This type of blade breaks easily.
Do not touch the blade after sawing until it has cooled. The blade gets very hot during the sawing.
Never use the tool without the insert plate. If the insert plate is defective, replace it. A fault on the insert plate can result in an injury from the saw blade.
Check the power cord at regular intervals. A damaged cord must be replaced by an authorized service Centre. Replace the extension cord if it is damaged.
This maintains safety.
Always store the power tool safely.
The storage space must be dry and lockable so that the tool is not damaged and so no unauthorized person can access it.
Do not leave the tool unsupervised until it has come to a complete stop. Cutting tools that are still moving can cause injury.
Do not use the tool if the power cord is damaged. Do not touch a damaged cord, and pull out the plug if the cord is damaged during the work.
Damaged power cords increase the risk of electric shock.

BOTTOM BLADE GUARD

Never use the product without the bottom blade guard. If the bottom blade guard is damaged or not working properly, switch off the product immediately and pull out the plug. Do not use the product until it has been repaired. Check at regular intervals that the bottom guard is working properly. Clean the bottom guard when necessary with damp cloth.

REDUCTION OF NOISE AND VIBRATIONS

Plan the work so that exposure to heavy vibrations is spread over a longer period.
To reduce noise and vibrations when in use, limit the time the tool is in use, and use low-power/vibration mode and suitable safety equipment.
Take the following precautions to minimize the risks of exposure to vibrations and/or noise:
- Only use the tool in accordance with these instructions.
- Check that the tool is in good condition.
- Use accessories in good condition, and which are suitable for the purpose.
- Keep a firm grip on the handles/grips.
- Maintain and lubricate the tool in accordance with these instructions.

LASER

Do not look directly at the beam.
Never point the laser beam at reflective surfaces, people or animals. Even low power laser beams can damage the eyes.
Any deviation from the work method described here can result in a risk of dangerous exposure to radiation.
Never open the laser module.
It is not permitted to modify the laser in any way to increase the power of the laser.
The manufacturer cannot assume liability for any damage resulting from failure to follow the safety instructions.

SYMBOLS

Cord length 1.8 m
Safety class
Laser class 2
Wavelength, laser 650 nm
Laser power 1 mW
Sound pressure level, LpA 94.6 dB(A), K=3 dB
Sound power level, LwA 107.6 dB(A), K=3 dB

Always wear ear protection
The declared values for vibration and noise, which have been measured according to a standardized test method, can be used to compare different tools with each other and for a preliminary assessment of exposure.
The measurement values have been determined in accordance with EN 62841-3-9:2015.

WARNING!
The actual vibration and noise level when using tools may differ from the specified maximum value, depending on how the tool is used and the material being processed.
It is therefore necessary to determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages of the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start- up time).

DESCRIPTION

Power switch lock
Handle
Power switch
Bottom blade guard
Blade
Adjuster knob for mitre angle
Mitre lock
Saw table
Mitre angle scale
Bench extension
Clamp
Fence
Bevel angle lock knob
Bevel angle scale
Saw arm lock knob
Dust bag
Spindle screw
Lock pin for saw head

FUNCTIONS

Functions not described in this chapter are explained in other places in the manual.

Lock pin for saw head

Put the pin in the deep slot to lock the saw head.

FIG. 3

Put the pin in the shallow slot to release the saw head.

FIG. 4

Guard

The bottom guard is raised automatically
when the handle is moved down. When the handle is moved up the bottom guard returns automatically to safety mode. Keep your hands away from the blade when moving down the handle. Never attempt to stop the bottom guard.

Saw arm lock knob

Tighten the lock knob to prevent the saw head from moving back and forwards in short cuts, release to allow the saw head to move.

ASSEMBLY

Put the table extensions (70) in the holes on the side of the base. Tighten the thumbscrews holding the table extensions. The top of the table extensions should be level with the surface of the saw table. This gives a larger area for the workpiece to rest on.
Screw the adjuster knob for the mitre angle (6) firmly on the end of the saw table, over the mitre lock.
Put the dust bag (16) on the dust outlet on the back of the product.
Mount the product on a stable surface with screws in the 4 screw holes in the base. Mounting parts are sold separately in Jula’s department stores and at www.jula.com.

USE

WARRANTY

Avoid accidental starting. Switch off the product and pull out the plug before carrying out any of the measures in this section.
Always check that the product is in good condition before use. Check that all screw unions are tight, that moving parts are correctly adjusted and can move freely, that no parts are incorrectly fitted or defective, that no wires are damaged, and that there are no other factors that could affect functionality.
Do not use the product if the guards or covers are missing or damaged.
The guards must be able to move freely and should be closed immediately.

CHANGING THE BLADE

Switch off the product and pull out the plug.
Move the bottom blade guard up out of the way and keep it there.
Release the pivot on the guard to release the pivot plate.
Swing the pivot plate up out of the way.
Press in the spindle lock button on the back of the saw head.
Remove the spindle screw (17) and the outer flange
FIG. 5
IMPORTANT:
- The spindle screw has left-hand thread and screws out clockwise.
- Make sure that the inner flange (E) remains on the spindle.
  FIG. 6
Remove the blade (D) and centre hole insert (C). Put the centre hole insert in a new blade and fit the new blade. Check that the arrow on the blade points in the same direction as the arrow on the top guard.
Replace the outer flange (B) and tighten the spindle screw (17). Put the flange with domed side against the blade. Keep the spindle lock button pressed in and tighten the spindle screw anticlockwise. Release the spindle lock button.
Turn back the pivot plate and lock it with the guard pivot.

WARNING!

Check before use that the bottom guard moves easily and covers the blade.

USING THE TABLE EXTENSIONS

Put the table extensions (10) on each side of the table and lock in place with the thumbscrews.
The top of the table extensions should be level with the surface of the saw table and provide more space for the workpiece to rest on.
Support the workpiece so that it is level with the saw table and so that the sawn off parts do not drop down. Support long workpieces with roller supports, or the equivalent (sold separately).
If the workpiece is not horizontal the cut will be bevelled. Large workpieces that are not supported increase the risk of the blade jamming and causing kickback, which increases the risk of serious personal injury.

ADJUSTING THE MITRE ANGLE

Mitre sawing involves vertical sawing at the required angle in the horizontal plane. A mitre angle of 45° is used to join two pieces at right angles. A mitre angle of 30° is used for scarf joints or bevelled ends. Release the adjuster knob for the mitre angle by turning it a 1/4 turn anticlockwise.
Press down the mitre lock to release the saw table. Keep the mitre lock pressed in and move the saw table to the required angle.
Read off the angle on the mitre angle scale. When the mitre lock releases, lock the table at one of the mitre angles 22.5°, 30°, 45° or 90° to the left or right.
Tighten the adjuster knob for the mitre angle when the required mitre angle has been set.
Put the workpiece against the fence and lock it in place with the clamp to saw it.

ADJUSTING THE BEVEL ANGLE

The cut is angled in the vertical plane for bevel sawing. Bevel sawing can be used for mitre sawing of wide and thin workpieces. Bevel sawing and mitre sawing at the same time is called combination sawing. Combination sawing is used for crown mouldings and picture frames, etc.

Release the lock knob for the bevel angle on the back of the product.
Adjust the blade to the required angle. Read off the angle on the bevel angle scale.
Lock the blade by turning the lock knob for the bevel angle clockwise. Screw tight, but do not overtighten.
Saw a spare piece to test that the bevel angle is correct.

CLEANING

Wipe the product with a damp cloth after use.

CHECKING AND CALIBRATING THE FENCE

The fence holds the workpiece fixed in place, while the table and/or blade is set to the required mitre angle and/or bevel angle. For accurate sawing the fence must be at right angles (90°) to the blade.

Saw a spare piece with the saw table set to 3.Adjust the fence if the cut is not at 90°.Check the cut with a set square. If the cut is not completely vertical
The angle can also be checked by turning the pieces will form a slight angle.
one piece 180° and pressing the sawn 4. edges together.
Adjust the fence if the cut is not at 90°.

ADJUSTING THE FENCE

Bring down the saw head and lock it with the lock pin.
Place a set square on the table with one side against the blade and the other against the fence. Any deviation will be clearly visible. NOTE: The set square must be flush with the side of the blade, not against the teeth, for a correct reading.
The fence is fixed with a screw in each end. Undo the screws a little and carefully tap the fence to the correct position with a rubber mallet. Tighten the screws and check by sawing another spare piece. Repeat until the fence is correctly adjusted.
Firmly tighten the screws. Continue with the work after the test sawing.

CALIBRATION OF MITRE ANGLE SCALE.

When the fence angle has been checked and if necessary adjusted at 90° to the blade, check that the mitre angle scale is set correctly.

Undo the screw holding the mitre angle scale.
Turn it so that the pointer points to 90°.
Tighten the screw.

CALIBRATION OF BEVEL ANGLE SCALE

For accurate sawing the blade must be vertical in relation to the saw table.

Put the saw head in a vertical position to check the angle. Saw a thick spare piece of wood.
Check the cut with a set square. The angle of the cut should be exactly 90°.
The angle can also be checked by turning one piece 180° and pressing the sawn edges together.
If necessary the bevel angle setting can be adjusted with the adjuster screw on the right-hand side, below the lock knob for the bevel angle.
When the bevel angle has been adjusted, adjust the bevel angle scale so that it shows 0° when the blade is vertical. Undo the screw holding the pointer, adjust it so that it is directly over the 0° mark, and tighten the screw.

ADJUSTING OR REPLACING THE SAW TABLE

Bring down the saw head and lock it with the lock pin.
Adjust the saw table so that the right- hand side of the blade just clears the edge of the table.
Release the lock knob for the bevel angle and set the angle to 45° to the left.
Check that the left-hand side of the blade just clears the table.
Tighten the 4 screws that hold the saw table in place.

TROUBLESHOOTING

Problem	Possible cau s e	Proposed action
The product will not start.	No power.	Check that the power point is supplied

with voltage.
Check that the plug is plugged in.
The product works intermittently or lacks power.| Supply voltage too low, or unsuitable extension cord.| Check the power supply and the extension cord.
Worn or damaged carbon brushes.| Check the carbon brushes and replace them if they are damaged or worn.
Burn marks on the surface of the cut.| Dirt on the blade.| Clean the blade with alcohol, or white spirit.
The blade fastens in the workpiece.| Check that the workpiece is correctly placed on the saw table. The workpiece must be horizontal, pressed against the fence and supported at the ends.
| The machined side of the workpiece is turned down.| The machined side of the workpiece should be turned up. Splintering can easily take place on the underside and/or back.
The workpiece splinters.| Unsuitable blade for the material.| Follow the recommendations of the blade manufacturer for the material. When crosscutting hard wood and for precision sawing, use a thin blade with at least 60 teeth.
| The workpiece is not properly supported.| Place a thin spare piece of wood, for example 1/4″ plywood, under or behind the workpiece to counteract splintering the edges of the cut.
The blade fastens, the speed drops, or the product stops.| The workpiece is not positioned properly, or the ends are not properly supported.| The workpiece must be horizontal on the saw table, pressed against the fence and supported at the ends.
| The material is wet or contaminated, or the blade is not suitable for the material.| Check the condition of the material and that the blade is suitable for the material.
The blade does not go all the way through the workpiece.| The depth stop is applied.| Push the depth stop to the right so that it is not applied.
| The depth stop is not properly adjusted.| Adjust the depth stop screw to the required depth.