SKYDANCE LF-15A 0/1-10V Constant Current LED Driver User Manual

SKYDANCE LF-15A 01-10V Constant Current LED Driver

Features

• Dimming interface: 0-10V, 1-10V, 10V PWM, Resistor, AC Push-Dim
• Universal AC input / Full range
• Flicker-free
• 1 channel constant current output, configurable current via DIP switch
• Built-in active PFC function: 0.95 Type
• Synchronize on multiple number of LED drivers
• Over-heat / Over-load / Short circuit protection, recover automatically
• Full protective plastic case
• Suitable for indoor LED lighting application
• 5 Year, 50,000hr warranty
  

Applications

• Suitable for downlight, spotlight and decorative applications.
• Office / Commercial / Domestic Lighting, Hotels, Classrooms, Warehouse, Health care, Retail and Display.
• Use for retrot upgrades & new luminaire designs.

Mechanical Structures and Installations

Dimension

Technical Parameters

〜       ％

Dimming Range| 0 100 , dimmer depth:0.2%
PWM Frequency| 8000Hz
Current Accuracy| ±5％
Ripple & Noise| < 100mV
Input| Input Voltage Range| 100～240VAC
Frequency Range| 50/60Hz
Efficiency| >80%/230VAC
Alternating Current| 0.15A/115VAC, 0.07A/230VAC
Anti Surge| L-N:1.5KV
Startup time| 1S/230VAC
Power Factor| >0.98/115VAC,

0.93/230VAC

THD| <8%
Inrush Current| Cold start 13.7A at 230VAC
Leakage Current| < 0.5mA/230VAC
No Load Power| < 2W
Protection| Over Load Power| When O/P voltage exceed its range, O/P current declines, auto recovers when the load is reduced.
Short Circuit| Shut down automatically if short circuit occurs, auto recovers.
Over Temperature| Intelligently adjust or turn off the output current if the PCB temp > 100℃, auto recovers.
Environment| Working Temperature| -20℃～50℃
T-case Max| 80℃
Working Humidity| 20％～90％RH, non-condensing
Storage Temp/Humidity| -40℃～80℃, 10％～95％RH
Temperature Coefficient| ±0.03％/℃ (0-50％)
Vibration Resistance| 10-500Hz, 2G, 6min/cycle, X,Y,Z axes/2min
IP Rating| IP20
Safety & EMC| Security Specifications| IEC/EN61347-1, IEC/EN61347-2-13
Withstand Voltage| I/P-O/P: 3750VAC
Insulation Resistance| I/P-O/P: 100MΩ/500VDC/25℃/70％RH
EMC Emission| EN61000-3-2 Class C, IEC 61000-3-3
EMC Immunity| EN61000-4-2.3.4.5.6.8.11, EN 61547
Certifications| CE

LED Current Selection:

| | | | | | | | | | | |
---|---|---|---|---|---|---|---|---|---|---|---|---
Output Voltage| 9-45V| 9-45V| 9-45V| 9-45V| 9-43V| 9-38V| 9-33V| 9-30V| 9-27V| 9-25V| 9-23V| 9-22V
Output Current| 150mA| 200mA| 250mA| 300mA| 350mA| 400mA| 450mA| 500mA| 550mA| 600mA| 650mA| 700mA
Output Power| 1.35-6.75W| 1.8-9W| 2.25-11.25W| 2.7-13.5W| 3.15-15.05W| 3.6-15.2W| 4.05-14.85W| 500mA| 4.95-14.85W| 5.4-15 W| 5.85-14.95 W| 6.3-15.4 W

Wiring Diagram

1. 0/1-10V Connection
   

2. The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.

3. Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).

4. We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 50 pieces, The maximum length of the wires from dimmer to LED driver should be no more than 50 meters.

5. If the LED driver be used with Push-Dim interface prior to using the 0/1-10V interface, the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

6. The products shall not be stacked, the distance should be ≥ 20cm, so as not to affect lifespan of the products due to poor heat dissipation.

7. AC Push-Dim connection
   
   The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches.

   • Short press:
     Turn on or off light.

   • Long press (1-6s):
     Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction.

   • Dimming memory:
     Light returns to the previous dimming level when switched off and on again, even at power failure.

   • Synchronization:
     If more than one LED driver are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
     This means there is no need for any additional synchrony wire in larger installations.
     We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to LED driver should be no more than 20 meters.

Dimming Curve

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>