SKYDANCE T18 0-10V Touch Glass Panel Dimmer User Manual
- June 12, 2024
- SKYDANCE
Table of Contents
SKYDANCE T18 0-10V Touch Glass Panel Dimmer
Features
- Touch panel 0-10V dimmer, output 1 channel 0-10V signal.
- Output connect with 0/1-10V dimmable driver.
- Ultra sensitive high strength glass touch panel with touch slide in the middle.
- Compatibility with RF 2.4G dimming remote control.
- Touch keys with LED indicator.
- White & Black glass panel available.
Technical Parameters
Input and Output
Input voltage| AC100-240V
Output signal| 0-10V (50mA)
Output current| 20mA/CH
Dimming data
Input signal| Touch key + RF 2.4GHz
RF Control distance| 10m(Barrier-free space)
Dimming gray level| 256 levels
Dimming range| 0 -100%
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Warranty
Warranty| 5 years
Environment
Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| Ta: +65 OC
IP rating| IP20
Package|
Size| L112x W112 x H50mm
Gross weight| 0.238kg
Mechanical Structures and Installations
Dimension
Installation diagram:
Typical base as below:
Match Remote Control (two match ways)
The 0-10V touch panel dimmer can also match with the RF dimming remote
(optional).
End user can choose the suitable match/delete ways. Two options are offered
for selection:
Use On/Off key
Match:
Turn on light, turn off, immediately press the On/Off key of the panel for 5s,
then press on/off key (single zone remote) or zone key (multiple zone remote)
of the RF remote within 5s.
The LED indicator fast flash 3 times means match is successful.
Delete:
Turn on light, turn off, immediately press the On/Off key of the panel for 10s
to delete all match,
The LED indicator fast flash 6 times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again,
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again, Immediately short
press on/off key (single zone remote) or zone key (multiple zone remote) 5
times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Key function
Note: The default output is 0-10V, if you want to 1-10V output, please
touch power key to turn off light,
then long press power key for 15s immediately, the output will become 1-10V.
Touch power key to turn off light, then long press power key for 10s
immediately, the output will return 0-10V.
Wiring diagram
-
Connect with 0/1-10V dimming driver (no use AC OUT)
-
Connect with 0/1-10V dimming driver (use AC OUT)
-
Connect with 0/1-10V dimming driver (use AC OUT and relay or contactor)
An additional AC relay or contactor is needed when total input current of the load is higher than 1.5A or inrush current is greater than 15A.
Note: We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 100 pieces, the maximum length of the wires from dimmer to LED driver should be no more than 50 meters.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>