SKYDANCE V1-K Rotary Dimmer Owner’s Manual
- June 12, 2024
- SKYDANCE
Table of Contents
- INTRODUCTION
- Features
- Technical Parameters
- Mechanical Structures and Installations
- Wiring Diagram
- Match Remote Control (two match ways)
- PWM frequency setting
- Dimming curve setting
- Light on/off fade time
- Malfunctions Analysis & Troubleshooting
- Installation Precautions
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SKYDANCE V1-K Rotary Dimmer
INTRODUCTION
Rotary dimming/Numeric display/Max 20A/Four PWM frequency/Linear or logarithmic dimming/Multiple protection
Features
- Rotary dimmer with digital numeric display, visible dimming level.
- Match with RF 2.4G single zone or multiple zone dimming remote control optional.
- 0-100% dimming smoothly without any ash.
- High load current up to 20A.
- Logarithmic or linear dimming curve selectable.
- PWM frequency 500Hz, 2kHz, 8kHz or 16kHz selectable.
- Over-heat / Over-load / Short circuit protection, recover automatically.
- Light on/off fade time 3s selectable.
Technical Parameters
Input and Output
Input voltage| 12-48VDC
Input current| 20A
Output voltage| 12-48VDC
Output current| 1CH,20A Max.
Output power| 240W/480W@ (12V/24V) 500Hz
Output type| Constant voltage
Warranty
Warranty| 5 years
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Package
Size| L112x W80 x H45mm
Gross weight| 0.165kg
Dimming data
Input signal| Rotary knob + RF 2.4GHz
Control distance| 15m(Barrier-free space)
Dimming gray scale| 100levels
Dimming range| 0 -100%
Dimming curve| Logarithmic or linear
PWM Frequency| 500Hz, 2kHz, 8kHz, 16kHz
Environment
Operation temperature| Ta: -30 O C ~ +55 O W C
Case temperature (Max.)| T c:+85 O C
Mechanical Structures and Installations
Wiring Diagram
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use Match key
Match:
Short press match key, immediately press on/off key (single zone remote) or
zone key (multiple zone remote) on the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast
flash a few times means all matched remotes were deleted
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote. The light blinks 5 times means all matched
remotes were deleted.
PWM frequency setting
-
16KHz 10A 8A
-
8KHz 10A 8A
-
2KHz 15A 12A
-
500Hz 20A 15A
(12-24V) (36-48V)
We can select four PWM frequency: 500Hz, 2kHz, 8kHz or 16kHz.
Higher PWM frequency, will cause lower output current, higher power noise, but
more suitable for camera(No flickers for video).
Dimming curve setting
Light on/off fade time
Long press match key 5s, then short press match key 3 times, the light on/off
time will be set to 3s, the indicator light blink 3 times.
Long press match key 10s, restore factory default parameter, the light on/off
time also restore to 0.5s.
Malfunctions Analysis & Troubleshooting
Malfunctions | Causes | Troubleshooting |
---|---|---|
No light |
- No power.
- Wrong connection or insecure.
|
- Check the power.
- Check the connection.
Uneven intensity between front and rear, with voltage drop|
- Output cable is too long.
- Wire diameter is too small.
- Overload beyond power supply capability.
- Overload beyond controller capability.
|
- Reduce cable or loop supply.
- Change wider wire.
- Replace higher power supply.
- Add power repeater.
Installation Precautions
- The products shall not be stacked, the distance should be ≥ 20cm, so as not to affect lifespan of the products due to poor heat dissipation.
- The product shall not be installed close to the switching power supply with an interval of ≥ 20cm to avoid the radiation interference of the switching power supply.
- The installation height shall be ≥ 1m from the oor to avoid shortening the remote control distance due to too weak reception signal.
- The products are not allowed to be close to or covered by metal objects, with an interval of ≥ 20cm to avoid signal attenuation and shorten the remote control distance.
- Avoid installation at the corner of the wall or the corner of the beam, with an interval of ≥ 20cm to avoid signal interference.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>