SKYDANCE D4-L 4 Channel Constant Voltage DMX512 and RDM Decoder Owner’s Manual

SKYDANCE D4-L 4 Channel Constant Voltage DMX512 and RDM Decoder

Product Information

4 Channel Constant Voltage DMX512 & RDM Decoder

Model No.: D4-L

Features:

• Comply with the DMX512 standard protocols
• Digital numeric display, set DMX decode start address by buttons
• RDM function for intercommunication between DMX master and decoder
• 1/2/4 DMX channel output selectable
• 16bit (65536 levels) /8bit (256 levels) grey level selectable
• PWM frequency 250/500/1000/2000/4000/8000/16000Hz selectable
• Logarithmic or linear dimming curve selectable
• Stand-alone RGB/RGBW mode and 4 channel dimmer mode selectable with built-in programs
• Over-heat / Short circuit protection, recover automatically

Technical Parameters:

• Input voltage: 12-24VDC
• Input current: 20.5A
• Output voltage: 4 x (12-24)VDC
• Output current: 4CH,5A/CH
• Output power: 4 x (60-120)W
• Output type: Constant voltage

Safety and EMC:

• EMC standard (EMC)
• Safety standard(LVD)
• Radio Equipment(RED)
• Certification: ETSI EN 301 489-1 V2.2.3, ETSI EN 301 489-17 V3.2.4, EN 62368-1:2020+A11:2020, ETSI EN 300 328 V2.2.2, CE, EMC, LVD
• Warranty: 5 years

Environment:

• Operation temperature: -30°C ~ +55°C
• Case temperature (Max.): +70°C
• IP rating: IP20
• Package Size: L175x W54 x H27mm
• Gross weight: 0.130kg

Mechanical Structures and Installations:

Wiring Diagram:

AC100-240V Power Supply -> 12-24VDC Constant Voltage ->DMX Master -> D4-L DMX512 & RDM Decoder -> RGBW LED strip

Note:

1. An DMX signal amplifier is needed if more than 32 decoders are connected, or use overlong signal line, signal amplification should not be more than 5 times continuously.
2. If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W 90-120 terminal resistor at the end of each DMX signal line.

Product Usage Instructions

System parameter setting:

1. Long press M and key in the same time for 2s to prepare for setting up system parameters.

2. Short press M key to switch between six items:

1. Decode mode: Use short press or key to switch 1/2/4 channel decode mode (d-1, d-2, or d-4). When set as 1 channel decode, the decoder occupies only 1 DMX address, and the four channels output the same brightness of this DMX address.
2. Grey level: Use short press or key to switch between 8bit (b08) or 16bit (b16). Choose 16bit if the DMX master supports 16bit.
3. Output PWM frequency: Use short press or key to switch between different frequencies: 250Hz (F02), 500Hz (F05), 1000Hz (F10), 2000Hz (F20), 4000Hz (F40), 8000Hz (F80).
4. Output brightness curve: Use short press or key to switch between logarithmic or linear dimming curve.
5. Default output level
6. Automatic blank screen

DMX mode:

1. Short press M key, when display shows 001~512, enter DMXmode.

2. Press or key to change DMX decode start address (001~512), long press for fast adjustment.

3. If there is a DMX signal input, the decoder will enter DMX mode automatically.

4. DMX Dimming: Each D4-L DMX decoder occupies 4 DMX addresses when connecting to the DMX console.

Features

• Comply with the DMX512 standard protocols.
• Digital numeric display, set DMX decode start address by buttons.
• RDM function can realize intercommunication between DMX master and decoder. For example, DMX decoder address can be set by DMX master console.
• 1/2/4 DMX channel output selectable.
• 16bit (65536 levels) /8bit (256 levels) grey level selectable.
• PWM frequency 250/500/1000/2000/4000/8000/16000Hz selectable.
• Logarithmic or linear dimming curve selectable.
• Stand-alone RGB/RGBW mode and 4 channel dimmer mode selectable, which be controlled by buttons with built-in programs, instead of DMX signal.
• Over-heat / Short circuit protection, recover automatically.

Technical Parameters

Input and Output

Input voltage| 12-24VDC
Input current| 20.5A
Output voltage| 4 x (12-24)VDC
Output current| 4CH,5A/CH
Output power| 4 x (60-120)W
Output type| Constant voltage
Safety and EMC

EMC standard (EMC)

| ETSI EN 301 489-1 V2.2.3

ETSI EN 301 489-17 V3.2.4

Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certi cation| CE,EMC,LVD
Warranty| 5 years
Environment

Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| Ta: +70 OC
IP rating| IP20
Package|
Size| L175x W54 x H27mm
Gross weight| 0.130kg

Mechanical Structures and Installations

Wiring Diagram

Note:

1. An DMX signal amplifier is needed if more than 32 decoders are connected, or use overlong signal line, signal amplification should not be more than 5 times continuously.
2. If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W 90-120Ω terminal resistor at the end of each DMX signal line.

Operation

System parameter setting

• Long press M and ◀ key in the same time for 2s, prepare for setup system parameter: decode mode, grey level, output PWM frequence, output brightness curve, default output level, automatic blank screen. short press M key to switch six item.
• Decode mode: short press ◀ or ▶ key to switch 1/2/4 channel decode mode(”d-1“,”d-2“ or ”d-4“). When set as 1 channel decode, the decoder occupy only 1 DMX address, and four channel output the same brightness of this DMX address.
• Grey level: short press ◀ or ▶ key to switch 8bit(”b08“) or 16 bit(”b16“). choose 16 bit if the DMX master support 16 bit.
• Output PWM frequency: short press ◀ or ▶ key to switch 250Hz(”F02“), 500Hz(”F05“), 1000Hz(”F10“), 2000Hz(”F20”), 4000Hz(”F40”), 8000Hz(”F80”) or 16000Hz(”F16”). Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No ?ickers for video).
• Output brightness curve: short press ◀ or ▶ key to switch linear curve(”C-L“) or logarithmic curve(”C-E“).
• Default output level: press ◀ or ▶ key to change default 0-100% level (”d00“ to ”dFF“ ) when no DMX input signal.
• Automatic blank screen: short press ◀ or ▶ key to switch enable (”bon“) or disable(”boF“) automatic blank screen.
• Long press M key for 2s or timeout 10s, quit system parameter setting.

DMX mode

• Short press M key, when display 001~512, enter DMX mode.
• Press ◀ or ▶ key to change DMX decode start address(001~512), long press for fast adjustment.
• If there is a DMX signal input, will enter DMX mode automatically.
• DMX Dimming: Each D4-L DMX decoder occupy 4 DMX address when connecting the DMX console. For example, the defaulted start address is 1, their corresponding relationship in the form:
  DMX Console| DMX Decoder Output
  ---|---
  CH1 0-255| CH1 PWM 0-100% (LED R)
  CH2 0-255| CH2 PWM 0-100% (LED G)
  CH3 0-255| CH3 PWM 0-100% (LED B)
  CH4 0-255| CH4 PWM 0-100% (LED W)

Stand-alone RGB/RGBW mode

• Enter stand-alone RGB/RGBW mode only when DMX signal is disconnected or lost.
• Short press M key, when display P01~P30, enter stand-alone RGB/RGBW mode.
• Press ◀ or ▶ key to change dynamic mode number(P01~P30).
• Each mode can adjust speed and brightness.
• Long press M key for 2s, prepare for setup mode speed, brightness, W channel brightness. Short press M key to switch three item.
• Press ◀ or ▶ key to setup value of each item.
• Mode speed: 1-10 level speed(S-1, S-9, S-F).
• Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
• W channel brightness: 0-255 level brightness(400-4FF).
• Long press M key for 2s, or timeout 10s, quit setting.

Stand-alone dimmer mode

• Enter stand-alone dimmer mode only when DMX signal is disconnected or lost.
• Short press M key, when display L-1~L-8, enter stand-alone dimmer mode.
• Press ◀ or ▶ key to change dimmer mode number(L-1~L-8).
• Each dimmer mode can adjust each channel brightness independently.
• Long press M key for 2s, prepare for setup four channel brightness.
• Short press M key to switch four channel(100~1FF, 200~2FF, 300~3FF, 400~4FF). Press ◀ or ▶ key to setup brightness value of each channel.
• Long press M key for 2s, or timeout 10s, quit setting.

Restore factory default parameter

• Long press ◀ and ▶ key for 2s, restore factory default parameter, display”RES”.
• Factory default parameter: DMX decode mode, DMX decode start address is 1, four channel decode, 8 bit grey level, 2000Hz PWM frequence output, logarithmic brightness curve, output 100% level when no DMX input, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.

RGB change mode list

Malfunctions analysis & troubleshooting

No light

| 1.  No power.

2.  Wrong connection or insecure.

| 1.  Check the power.

2.  Check the connection.

Wrong color| 1.  Wrong connection of R/G/B/W wires.

2.  DMX decode address error.

| 1.  Reconnect R/G/B/W wires.

2.  Set corrrect decode address.

Uneven intensity between front and rear,with voltage drop| 1.  Output cable is too long.

2.  Wire diameter is too small.

3.  Overload beyond power supply capability.

4.  Overload beyond controller capability.

| 1. Reduce cable or loop supply.

2. Change wider wire.

3. Replace higher power supply.

4. Add power repeater.

Dimming curve setting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>