VISUAL COMFORT JN5331 Chalmette 16 Inch Layered Pendant Instruction Manual

: June 12, 2024
: VISUAL COMFORT

Table of Contents

VISUAL COMFORT JN5331 Chalmette 16 Inch Layered Pendant
Product Information
Product Usage Instructions
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
Care Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VISUAL COMFORT JN5331 Chalmette 16 Inch Layered Pendant

Product Information

Chalmette 16 Layered Pendant

Item Number: JN5331
Bulbs not included

This product is a Chalmette 16 Layered Pendant, designed to provide lighting in a stylish and decorative manner. It is important to follow the assembly and installation instructions carefully to ensure safe and proper usage.

Product Usage Instructions

Carefully remove all parts from the box and place them on a clean, soft surface.
Remove collar loop (D) from chain (H) by removing quick link (E).
Install the mounting plate (B) to the junction box using the provided mounting screws (C).
Secure collar loop (D) to the mounting plate (B) using pliers to tighten the locknut.
Install the canopy (F) to the collar loop (D) and secure it with the collar ring (G).
Determine the desired overall length and amount of chain (H) needed. Shorten the chain using chain pliers, keeping any extra chain for future use.
Attach the chain (H) to the collar loop (D) and fixture loop (I) using quick links (E). Secure the quick links (E).
Thread the fixture wire and ground wire through the chain (H). When reaching the collar loop (D), ensure there is no tension on the wires. Cut any excess wires, leaving enough to reach the junction box.
Separate the two sides of the molded wire and strip insulation on each side by 5/8 inch.
Loosen the collar ring (G) and carefully let the canopy (F) slip down the chain (H).
Twist all fixture wires together and slip them through the center hole of the collar loop (D). Untwist the wires and separate them to prepare for connection.
Wrap the fixture ground wire (bare copper) around the green grounding screw and tighten it.
Continue the fixture ground wire and connect it to the supply ground wire (usually green or bare copper) using a wire nut (A). It is essential to ensure proper grounding.
Connect the fixture neutral wire (ribbed) to the supply neutral wire (usually white) using a wire nut (A).
Connect the fixture hot wire (smooth with markings) to the supply hot wire (usually black) using a wire nut (A). Take caution not to reverse the hot and neutral connections.
Ensure all wire connections are tight, then carefully tuck them into the junction box.
Install the canopy (F) to the collar loop (D) and secure it with the collar ring (G).
Install light bulbs into the sockets.

Care Instructions
Clean the pendant light only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents for cleaning.

ASSEMBLY INSTRUCTIONS

Chalmette 16″ Layered Pendant
Item # JN5331
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED

(NOT INCLUDED):

Phillips Screwdriver
Slip Joint Pliers
Wire Strippers
Slotted Screwdriver
Measuring Tape
Chain Pliers
Wire Cutters

Carefully remove all parts from the box. Place on a clean, soft surface.
Remove collar loop (D) from chain (H) by removing quick link (E).
Install mounting plate (B) to the junction box and secure with mounting screws (C).
Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.
Install canopy (F) to collar loop (D) and secure with collar ring (G).
Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain)
Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E).
Thread fixture wire and ground wire through chain (H).
NOTE : When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.
Separate two sides of molded wire, and strip insulation on each 5/8″.
Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully.
Twist all fixture wires together, and slip through center hole of collar loop (D).
NOTE: Untwist wires and separate to prepare for connection.
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.