SW-MOTECH BC.HTA.06.869.30001-B Side Case Set Instruction Manual

June 12, 2024
SW-MOTECH

SW-MOTECH-LOGO

SW-MOTECH BC.HTA.06.869.30001-B Side Case Set

Product Information

The product code for this item is BC.HTA.06.869.30001/B. It is part of the HTA series with the model numbers HTA.06.869.10001, HTA.06.869.11001, BC.HTA.00.677.10000L/B, and BC.HTA.00.677.10000R/B.

Product Usage Instructions

  1. Start by unpacking the product and ensuring that all components are included.
  2. Select the appropriate model number based on your specific requirements.
  3. Identify the desired location for installation.
  4. Prepare the installation area by cleaning and ensuring it is free from any obstructions.
  5. Position the product in the designated area, ensuring it is securely placed.
  6. Follow the provided wiring diagram to connect any necessary cables or power sources.
  7. Double-check all connections to ensure they are secure and properly installed.
  8. Refer to the user manual for any additional setup or configuration instructions specific to your model number.
  9. Once everything is properly connected and configured, turn on the product using the designated power switch.
  10. Follow the user manual for detailed instructions on how to operate and utilize the features of the product.

Note: If you encounter any difficulties during installation or usage, please refer to the troubleshooting section of the user manual or contact our customer support for assistance.

SLC side carrier
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and / or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and or maintenance work! Carefully follow all the directions given in the mounting instructions and payattention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and , or stability of your vehicle.

GENERAL INFORMATION

Observe the country specific regulations concerning vehicle registration / operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must bereinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and / or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PARTS LIST

SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(19\)

Note: All measurements in millimeters. second number indicates the total quantity of the part in the delivery. No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can used long as it is within the vehicle manufacturer’s specifications.SW-MOTECH-BC-
HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(1\)

  • All measurements in millimeters.
  • The second number indicates the total quantity of the part in the delivery
  • No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(2\)

MOUNTING

Remove the passenger seat from the vehicle. Remove the shown screws, then remove the seat as well.SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(3\)

Remove the marked plastic dowels and the fairing from the vehicle.
NOTE: The fairing is not required after mountingSW-MOTECH-BC-
HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(4\)

Remove the marked screws and detach the side fairings.SW-MOTECH-BC-
HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(5\)

Remove the shown screws from the fender.SW-MOTECH-BC-HTA-06-869-30001-B
-Side-Case-Set-FIG-1 \(6\)

Cut out the templates carefully. Place the templates on the insides of the side fairings, as shown in the drawing.
NOTE: Fix the templates with adhesive tape. Use a center punch to mark the center points of the drill positions on the inner sides of the side fairings. Use the indents for the center points. Use a 5 mm metal drill to drill the mountings holes. Use a stepped drillbit to enlarge the mountings holes to 17 mm. Deburr the edges of the mounting holes. Reattach the side fairings with the part shown in step [3].SW-MOTECH-BC-HTA-06-869-30001-B
-Side-Case-Set-FIG-1 \(7\)

NOTE: The mounting steps [7] to [10] show the mounting of the right side carrier. Mount the left side carrier in the same way as on the right side of the vehicle. Attach the parts (2] to (6) to the side carrier (1), as shown in the drawing.
ATTENTION: Use liquid thread locker! Tighten the screws as specified .SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(8\)

Remove the rear screw from the passenger footrest mount, as shown in the drawing.SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(9\)

NOTE: When mounting both side carriers, one set of parts (7) to (10) are not needed.
NOTE: When mounting the side carrier with an ALU RACK the mounting bracket (7) ist not needed. Attach the mounting bracket (7) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker! Do not fully tighten the screws yet .SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(10\)

NOTE: When mounting the side carrier with the ALU RACK the spacer (14) ist not needed. Attach the side carrier (1) to the mounting bracket (7] and the passenger footrest mount, as shown in the drawing.
ATTENTION: Use liquid thread locker! Once all parts are evenly positioned without excess tension, tighten all screws as specified.SW-MOTECH-BC-
HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(11\)

TEMPLATE

SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(12\)

MOUNTING INSTRUCTIONS

URBAN ABS side case
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required re.a, Abc cerrications are also available for gown oad at our webshoo. Installation and / or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and / or maintenance work!  Carefully follow all the directions given in the mounting instructions and payattention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver!These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration / operation as well as TÜV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system, Use appropriate tools. Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. Aiter tixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprenensive check of all functions.

PRODUCT SPECIFIC INFORMATION

  • ATTENTION: Riding with this product may affect the motorcycles driving and braking performance!
  • ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
  • ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(13\)
  • ATTENTION: The maximum vehicle load specified by the manufacturer must not be exceeded!
  • ATTENTION: NOT FOR OFFROAD-USE!

PARTS LIST

  • All measurements in millimeters.
  • The second number indicates the total quantity of the part in the delivery.
  • No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

Care
To clean the side case, use warm, soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Clean the side case after riding in salty conditions, to avoid damage from salt. Hard to open zippers can be loosened with a small amount of talcum powder.
ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG,  acid rain, etc.)! SW-MOTECHassumes no liability for this.

MOUNTING

Place the three locking openings of the side case onto the guide bolts of the mounted SLC side carrier. Then press the side case slightly downward, until it properly rests on the SLC side carrier.
ATTENTION: Make sure that all three guide bolts engage at the same time! Pay attention to the clearly audible snap sound of the locking mechanism and that the red marking under the slider is not visible! To release press the slider downward.
ATTENTION: All components of the side case must not contact any hot or moving parts of the vehicle! All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream! After mounting, make sure there are no clearance issues while the suspension is both compressed and extended.SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(15\)

Open the mounted side case (1) to protect it against theft.Now press the locking button and turn it according to the arrow mark until the locking button engages. Then lock the closed zipper with the included lock (2) We recommend leaving the locking button in the closed position during the ride .SW-MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1
\(16\)

Use the included waterproof inner bag (3) to protect your luggage from moisture. For easier loading of the side case (1), open the buckles and hook and loop fasteners of the opening reductions, as shown in the drawing.SW-
MOTECH-BC-HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(17\)

ATTENTION: Make sure weight is evenly distributed between the left and right side if you want to use both side cases! Make sure that the landing is secured against shifting during the ride!
ATTENTION: Never store pointy or sharp-edged objects, which could cause injury to persons or damage to the vehicle/side case!SW-MOTECH-BC-
HTA-06-869-30001-B-Side-Case-Set-FIG-1 \(18\)

Errors and omissions excepted. Technical and design modifications are subject to change.

CONTACT

  • SW-MOTECH GmbH & Co. KG
  • Tel. / phone + 49 (0)6425 / 8168 – 050
  • Ernteweg 8/10
  • Fax/fax + 49 (0)6425 / 8168 – 10
  • 35282 Rauschenberg
  • info@sw-motech.com.
  • Germany
  • www.sw-motech.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SW-MOTECH User Manuals

Related Manuals