SW-MOTECH BC.HTA.06.851.30000-B Side Case Set Instruction Manual
- June 12, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.06.851.30000-B Side Case Set
Product Information
The product is a set of attachments for a specific model of BC.HTA machine. The attachments included are HTA.06.851.10000, HTA.06.851.11000, BC.HTA.00.677.10000L/B, and BC.HTA.00.677.10000R/B.
Product Usage Instructions
- Ensure that the BC. The HTA machine is turned off and unplugged.
- Identify the attachment required for your specific task:
- – HTA.06.851.10000: This attachment is suitable for general use and can be used for various tasks.
- – HTA.06.851.11000: This attachment is designed for specific cutting tasks and should be used accordingly.
- – BC.HTA.00.677.10000L/B: This attachment is suitable for left-handed users and provides ergonomic support.
- – BC.HTA.00.677.10000R/B: This attachment is suitable for right-handed users and provides ergonomic support.
- Once you have identified the correct attachment, align it with the attachment slot on the BC.HTA machine.
- Slide the attachment into the slot until it clicks securely into place.
- Ensure that the attachment is firmly attached to the machine before proceeding.
- Connect the BC.HTA machine to a power source and turn it on.
- Depending on the specific task, adjust the speed and settings of the machine as required.
- Use the BC.HTA machine with the attached accessory to perform the desired task.
- Once the task is completed, turn off the BC.HTA machine and disconnect it from the power source.
- Remove the attachment from the machine by gently sliding it out of the slot.
- Store the attachment in a safe place until it is needed again.
SLC side carrier
Thank you for choosing this premium product from SW-MOTECH.Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain] are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TÜV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturer’s specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with a medium-strength liquid thread locker. Torque specifications
undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a
specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PARTS LIST
Note: All measurements are
in millimeters.
- The second number indicates the total quantity of the part in the delivery.
No torque specifications: Use the torque defined by the vehicle
manufacturer! The standard torque in this table can be used as long as it is
within the vehicle manufacturer’s specifications.
MOUNTING
NOTE: The following mounting steps show the mounting of the left side
carrier. Mount the right side carrier in the same way. Attach the parts (2] to
(5) to the side carrier (1)
ATTENTION: Use liquid thread locker! Tighten the screws as specified
.
Remove the original screws from the shown mounting points of the vehicle.
Attach the side carrier (1] to the rear of the vehicle, as shown.
ATTENTION: Use a liquid thread locker! Tighten the screws with the
manufacturer’s specified torque.
MOUNTING INSTRUCTIONS
URBAN ABS side case
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications) are also available for download at our webshop. Installation
and/or maintenance of this product requires good technical understanding! For
your own safety, SW-MOTECH recommends having installation and/or servicing
carried out by a specialist workshop! SW-MOTECH assumes no liability for
damage caused by improper installation and/or maintenance work! Carefully
follow all the directions given in the mounting instructions and pay attention
to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist. This product was developed for
vehicles in their factory setting. Compatibility with original accessory parts
or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE
installing this product, make sure that all moving parts (e.g. the chain) are
in the original state of maintenance. Installed accessories can change the
driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle
registration/operation as well as TUV regulations if applicable. If required,
register installed parts in the vehicle documents through an appropriate
inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type. After fixation also make sure that no moving
parts are obstructed and the function of the vehicle is not hindered in any
way. Lamps as taillights and turn signals must not be limited in their
function. Cables and hoses must not rub and/or be pinched. Before starting to
ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
- ATTENTION: Riding with this product may affect motorcycle driving and braking performance!
- ATTENTION: Depending on the location of fixation, cornering, and ground clearance can be reduced by using this product!
- ATTENTION: Before riding and at each stop (every 200 km) check the proper fixation of the product
| Maximum Load | Maximum Speed |
|---|---|
| j **5 KG** (11 lbs) per case | 130 km/h (80 mph) |
- ATTENTION: The maximum vehicle load specified by the manufacturer must not be exceeded!
- ATTENTION: NOT FOR OFFROAD USE!
PARTS LIST
All measurements in millimeters.
- The second number indicates the total quantity of the part in the delivery.
No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
Care
To clean the side case, use warm, soapy water and a soft, clean cloth. Rinse
with clean water. Do NOT use strong cleaning agents, rough cleaning tools or
high pressure washer! Clean the side case after riding in salty conditions, to
avoid damage from salt. Hard to open zippers can be loosened with a small
amount of talcum powder.
ATTENTION: Surface materials can experience color changes or fading when
exposed to direct sunlight for extended periods of time and by environmental
factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for
this.
MOUNTING
Place the three locking openings of the side case onto the guide bolts of the
mounted SLC side carrier. Then press the side case slightly downward, until it
properly rests on the SLC side carrier.
ATTENTION: Make sure that all three guide bolts engage at the same time!
Pay attention to the clearly audible snap sound of the locking mechanism and
that the red marking under the slider is not visible! To release press the
slider downward,
ATTENTION: All components of the side case must not contact any hot or
moving parts of the vehicle! All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream! After mounting,
make sure there are no clearance issues while the suspension is both
compressed and extended.
Open the mounted side case (1] to protect it against theft. Now press the
locking button and turn it according to the arrow mark until the locking
button engages. Then lock the closed zipper with the included lock (2)We
recommend leaving the locking button in the closed position during the ride
.
Use the included waterproof innerbag (3) to protect your luggage from
moisture. For an easier loading of the side case (1), open the buckles and
hook and loop fasteners of the opening reductions, as shown in the drawing
.
ATTENTION: Make sure weight is evenly distributed between the left and
right side if you want to use both side cases! Make sure that the loading is
secured against shifting during the ride!
ATTENTION: Never store pointy or sharp-edged objects, which could cause
injury to persons or damage to the vehicle/side case! Errors and omissions
excepted. Technical and design modifications are subiect 1 change. Errors and
omissions excepted. Technical and design modifications are subject to change.
CONTACT
- SW-MOTECH GmbH & Co. KG
- Ernteweg 8/10
- 35282 Rauschenberg
- Germany
- Tel. / phone + 49 (0)6425 / 8168 – 050
- Fax/fax + 49 (0)6425 / 8168 – 10
- infosw-motech.com.
- www.sw-motech.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>