Milesight AT101 Asset Tracker User Guide
- June 12, 2024
- Milesight
Table of Contents
Milesight AT101 Asset Tracker
Product Information
The AT101 Asset Tracker is a device featuring LoRaWAN technology. It is
designed to track and monitor assets using low-power long-range communication.
The tracker is equipped with NFC (Near Field Communication) for easy setup and
configuration.
The device has a power button for turning it on/off and resetting it to
factory default settings. It also has LED indicators to display its status.
The AT101 tracker comes with a packing list and can be fixed to target places using either mounting kits or 3M tape. It is compliant with FCC regulations and has been tested to meet radiation exposure limits for an uncontrolled environment.
To download software and files related to the device, please visit https://www.milesight-iot.com/documents-download/
Product Usage Instructions
- Check the packing list to ensure all components are included.
- To power on the device, remove the cover and press and hold the power button for more than 3 seconds. The LED indicator should turn on.
- To power off the device, press and hold the power button for more than 3 seconds. The LED indicator should turn off.
- To reset the device to factory default settings, press and hold the power button for more than 10 seconds.
- To check the on/off status of the device, quickly press the power button. The LED indicator will blink quickly if the device is on, and it will remain off if the device is off.
- For configuration:
- Download the Milesight ToolBox App on a Bluetooth-supported smartphone (available for Android and iOS).
- Enable the Bluetooth function on your smartphone.
- Open the ToolBox App and click on “Bluetooth Connect”. Enter the Bluetooth password (default: 123456).
- Read/write the device until the App shows a successful prompt.
- For installation:
- If using mounting kits, fix the device to target places using two M4 mounting screws and wall plugs.
- If using 3M tape, attach the tape to the back of the AT101 and then attach it to the measured object.
For any further assistance or technical support, please consult the product dealer or an experienced radio/TV technician.
Note: Please comply with FCC rules and guidelines when operating the device. Ensure a minimum distance of 20cm between the device and your body to comply with radiation exposure limits.
Packing List
Hardware Introduction
Power Button Patterns
AT101 tracker equips with power button inside the device, please remove the cover for emergency switch on/off. Usually users can use NFC to complete all steps.
| Function | Action | LED Indicator |
|---|
Power On
| Press and hold the power button for more than 3 seconds.|
Off → On
Power Off
| Press and hold the power button for more than 3 seconds.|
On → Off
Reset to Factory Default| Press and hold the power button for more than 10 seconds.|
Blinks quickly
Check On/Off Status
|
Quickly press the power button.
| Light On： Device is On.
Light Off： Device is Off.
Configuration Guide
- Download “Milesight ToolBox” App on a Bluetooth-supported smartphone.
- Enable the Bluetooth function on your smart phone before opening ToolBox App. Click “Bluetooth Connect” and enter the Bluetooth password to read/write the device until App shows a successful prompt. (The default Bluetooth password: 123456).
Note:
- NFC password is the same as Bluetooth password.
- If the Bluetooth password is entered over 1min, please re-enter the password.
- The waiting interval will be increased gradually after the fifth time if entering the incorrect password continuously, the maximum interval is 15min.
- It will disconnect Bluetooth automatically and require re-enter password if there is no data interaction after establishing the Bluetooth connection.
- It’s not supported to connect one sensor to multiple phones via
Bluetooth at the same time; the connection on phone A will be disconnected after phone B is connected to the sensor via Bluetooth.
Installation
Fixed by Mounting Kits
Install the device to target places by using two M4 mounting screws and wall
plugs.
Fixed by 3M Tape
Attach the 3M Tape to the back of AT101, tear another part and attach it to
the measured object
FCC Statement
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and.
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Quick Start Guide Cloud App
All software & files can be downloaded from https://www.milesight-iot.com /documents-download/
Milesight IoT Co., Ltd. www.milesight-iot.com
Building C09, Software Park Phase III, Xiamen 361024, Fujian, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>