Milesight CT10x Smart Current Transformer User Guide

Milesight CT10x Smart Current Transformer

Safety Precautions

• Milesight will not shoulder responsibility for any losses or damages resulting from not following the instructions of this operating guide.
• The device must not be modified in any way.
• The installation and maintenance must be conducted by a qualified service person and should strictly comply with the electrical safety regulations of the local region.
• Do not overload the maximum capacity to avoid damage to the device.
• The device is intended only for indoor use. Do not place the device where the temperature is below/above the operating range.
• Do not place the device close to objects with naked flames, heat source (oven or sunlight), cold source, liquid and extreme temperature changes.
• Keep the device away from water to prevent electric shock.
• Use the device opening clean and free of dust before installation. Dusty or dirty environments may prevent the proper operation of this device.
• Do not drop the device or subject it to physical shocks and strong vibration.

Declaration of Conformity
CT10x conforms with the essential requirements and other relevant provisions of the CE, FCC and RoHS.

Copyright 2011-2024 Milesight. All rights reserved.
All information in this guide is protected by copyright law. Whereby, no organization or individual shall copy or reproduce the whole or part of this user guide by any means without written authorization from Xiamen Milesight loT Co., Ltd.

For assistance, please contact
Milesight technical support:
Email: iot.support@milesight.com
Tel: 86-592-5085280
Fax: 86-592-5023065
Address: Building C09, Software Park Ill,
Xiamen 361024, China

Revision History

Product Introduction

Overview

CT10x is a LoRaWAN® Smart Current Transformer for monitoring energy and consumption remotely. CT10x provides multiple current options to suit energy monitoring and support sending threshold alarms. The compact size and clamp design allow it to be installed in any indoor space quickly and safely without de-energizing a facility, simplifying the installation and saving costs. Compliant with Milesight LoRaWAN® gateway and Milesight IoTCloudsolution, CT10x can be monitored via webpage or mobile App remotely. CT10x is widely used for energy motoring and billing in smart buildings, as well as for machine failure detection and prevention, etc. 1.2 Features

• Report the RMS current and accumulated current data by minutes
• High measuring accuracy with a sampling frequency of up to 3.3 kHz
• Self-powered, free from batteries or external wires
• Utilize a sampling rate of up to 1s for real-time monitoring and quick response
• Compact size allows for installation in narrow scenarios
• Non-invasive clamp design ensures easy and safe installation without the need for power de-energizing
• Equipped with LED indicator to indicate working status and alarms
• Compliant with standard LoRaWAN® gateways and network servers
• Compatibility with Milesight IoT Cloud

Hardware Introduction

Packing List

If any of the above items is missing or damaged, please contact your sales representative.

Hardware Overview

Button and LED Indicator

Low Power

Mode

| The device measures and reports at reduced rate.| Blinking every 5s
Low Voltage

Mode

| The device only measures at reduced rate.| Blinking every 10s
Alarm| The current is over the threshold or measuring

range.

| Fast Blinking
Reboot| Quick press the RST button once.| Blinking Once

Note: if not blinking even when the device is installed, the start circuit of the cable may be too small and will take some minutes to charge the device.

Dimensions (mm)

Operation Guide

USB Configuration
CT10x can be powered and configured via a Type-C port for configuration and debugging.

1. Download ToolBox software from the Milesight website.
2. Connect the device to a computer via the Type-C port.
3. open the ToolBox and select type as General, then click password to log into the ToolBox. (Default password: 123456)
4. After logging into the ToolBox, you can check the device status and change device settings.

LoRaWAN Settings
LoRaWAN settings are used to configure the data transmission parameters in the LoRaWAN®network.
Basic LoRaWAN Settings: CT10x supports basic configurations like join type, App EUI, App Key, and other information.
You also keep all settings by default.

is 85.
Join Type| OTAA and ABP modes are available.
Application Key| Appkey for OTAA mode, default is 5572404C696E6B4C6F52613230313823.
Device Address| DevAddr for ABP mode, default is the 5th to 12th digits of SN.
Network Session

Key

|

Nwkskey for ABP mode, default is 5572404C696E6B4C6F52613230313823.

Application

Session Key

|

Appskey for ABP mode, default is 5572404C696E6B4C6F52613230313823.

RX2 Data Rate| RX2 data rate to receive downlinks.
RX2

Frequency/MHz

|

RX2 frequency to receive downlinks.

Spread Factor| If ADR is disabled, the device will send data via this spread factor.

Confirmed Mode

| If the device does not receive the ACK packet from network server, it will

resend data once.

Rejoin Mode

| Reporting interval ≤ 35 mins: the device will send a specific number of LinkCheckReq MAC packets to the network server every reporting interval or every double reporting interval to validate connectivity; If there is no response, the device will re-join the network.

Reporting interval > 35 mins: the device will send a specific number of LinkCheckReq MAC packets to the network server every reporting interval to validate connectivity; If there is no response, the device will re-join the

network.

Set the number of| When rejoin mode is enabled, set the number of LinkCheckReq packets sent.
packets sent| Note: the actual sending number is Set the number of packets sent + 1.
---|---
ADR Mode| Allow the network server to adjust the data rate of the device.
Tx Power| Transmit power of the device.

Note

1. Please contact your sales representative for the device EUI list if there are many units.
2. Please contact your sales representative if you need random App keys before purchase.
3. Select OTAA mode if you use Milesight IoT Cloud to manage devices.
4. Only OTAA mode supports rejoin mode. LoRaWAN Frequency Settings
5. Select supported frequency and channels to send uplinks. Make sure the channels match the gateway.

If the device frequency is one of CN470/AU915/US915, you can enter the index of the channel that you want to enable in the input box, making them separated by commas. Examples:

• 1, 40: Enabling Channel 1 and Channel 40
• 1-40: Enabling Channel 1 to Channel 40
• 1-40, 60: Enabling Channel 1 to Channel 40 and Channel 60
• All: Enabling all channels
• Null: Indicates that all channels are disabled

General & Alarm Settings

Reporting Interval

| The interval of reporting current data. Default: 10 mins, Range: 1 – 1440 mins

Note: when the device is under low power mode, the interval is fixed as 30 minutes; when the device is under low voltage mode, the device will stop

reporting. The working mode can be judged by an LED indicator.

Change Password| Change the password of the device for ToolBox configuration.

Excessive Current

Threshold

|

The maximum current threshold value.

Insufficient Current

Threshold

|

The minimum current threshold value.

Alarm Reporting

Interval (min)

| The interval to report alarm packet after alarm triggers. This interval

should be less than reporting interval.

Alarm Reporting

Times

|

Alarm packet report times after alarm triggers.

Note
Overrange alarm is fixed as enabled, the alarm reporting interval is fixed as 5 minutes and the alarm reporting time is fixed as 3.

Maintenance

Upgrade
Download firmware from the Milesight website to your PC. 2. Go to Maintenance

Upgrade, click Browse to import firmware and click Upgrade to upgrade the device.

Backup
CT10x supports configuration backup for easy and quick device configuration in bulk. Backup is allowed only for devices with the same model and LoRaWAN® frequency band. 1. Go to Maintenance > Backup and Reset, and click Export to back up the device configuration. 2. Click Browse to import the backup file, then click Import to load the configuration.

Reset and Reboot
Reset to Factory Default: Go to Maintenance > Backup and Reset of ToolBox, and click Reset to complete.

Reboot
Quick press the RST button once or send a downlink command to reboot.

Installation

Antenna Installation
Rotate the antenna into the antenna connector. Ensure that the antenna is positioned vertically and is kept clear of metal objects and obstacles. Note: Keep the device away from metal objects, obstacles, or areas with other electrical equipment that may cause interference. If needed, consider opting for a magnetic antenna.

Transformer Installation

Open the current transformer to clip it around a single-phase wire. Then close the clip with a light “click” sound to confirm a firm grip on the wire.
Note: Do not place Phase wire and Neutral wire within a single current transformer.

Communication Protocol
All data are based on the following format (HEX), the Data field should follow little-endian:

For decoder examples, you can find them at https://github.com/Milesight- IoT/SensorDecoders.

Basic Information
CT10x reports basic information about the device whenever it joins the network.

ff

| 01(Protocol Version)| 1| 01=>V1
09 (Hardware Version)| 2| 02 10=>V2.1
0a(Software Version)| 2| 01 01=>V1.1
0b (Power On)| 1| Device is on

0f(Device Type)

|

1

| 00 = Class A, 01 = Class B, 02 =

Class C

16 (Device SN）| 8| 16 digits

Example

ff0bff ff0101 ff166746d48016300014 ff090110 ff0a0101 ff0f00

Channel| Type| Value| Channel| Type| Value
ff| 0b

(Power On)

| ff

(Reserved)

| ff| 01

(Protocol Version)

| 01

(V1)

Channel| Type| Value| Channel| Type| Value
ff| 16

(Device SN)

| 6746d48016300

014

| ff| 09

(Hardware Version)

| 0110

(V1.1)

Channel| Type| Value| Channel| Type| Value

ff

| 0a (Software

Version)

| 0101 (V1.1)|

ff

| 0f (Device Type)| 00

(Class A)

Sensor Data

Total Current

|

03

|

97

|

4

| UINT32/100, Unit: Ah, Resolution: 0.01 Ah

Note: when it reaches to max value FFFFFFFF (42949672.95), it will clear to 0 automatically.

Current

|

04

|

98

|

2

| UINT16/100, Unit: A, Resolution: 0.01 A Note: FFFF means collection failure.

Current Alarm

|

84

|

98

|

7

| Max. Current (2B) + Min. Current (2B) + Latest Current (2B) + Alarm Status (1B)

Alarm Status:

 |  |  |  | Bit0=1: Threshold alarm

Bit1=1: Threshold alarm dismiss Bit2=1: Overrange alarm

Bit3=1: Overrange alarm dismiss

Note: Max./Min. Current means the maximum or minimum value between last report and

current report.

---|---|---|---|---

Example

1. Periodic package: report as reporting interval (10 minutes by default).

Alarm or alarm dismiss packet

8498 b80b d007 c409 01

Channel| Type|

84

|

98(Current)

| Max. Current: b8 0b=>0b b8=3000/100=30A Min. Current: d0 07=>07 d0=2000/100=20A Latest Current: c4 09=>09 c4=2500/100=25A

Alarm Status: 01=>Bit1=1: Threshold alarm

Downlink Commands
CT10x supports downlink commands to configure the device.

Threshold Alarm

|

ff

|

06

| 9 Bytes, CTRL (1B) + Min (2B) + Max (2B) +

Alarm Reporting Times(2B) + Alarm Reporting Interval (2B)

CTRL:

08  – disable

09  – below (minimum threshold)

The application port is 85 by default.

039773020000 04980019

Channel| Type| Value| Channel| Type| Value

03

|

97 (Total Current)

| 73 02 00 00=>00 00

02 73=627/100

=6.27 Ah

|

04

|

98

(Current)

| 00 19=>19

00=6400/100

=64A

 |  |  | 0a – over (maximum threshold) 0b – within

0c – below or over Max./Min. Threshold unit: A

Alarm Reporting Interval unit: min

---|---|---|---
Clear Accumulated Current|

ff

|

27

| 01

Note: when

Example

1. Set the reporting interval as 20 minutes
   ff8e 00 1400

   Channel| Type| Value
   ff| 8e (Reporting Interval)| 14 00=>00 14= 20 mins

2. Reboot the device
   ff10ff

   Channel| Type| Value
   ff| 10 (Reboot)| ff

3. Enable current threshold alarm and set the maximum threshold as 60A, reporting times as2andreporting interval as 5 minutes
   ff 06 0a00003c0002000500

   Channel| Type| Value

ff

|

06

| CTRL:0a=Over maximum threshold Min: 00 00=0

Max: 3c 00=> 00 3c=60 A

Alarm Reporting Times: 02 00=>00 02=2

Alarm Reporting Interval: 05 00=>00 05 =5 mins

References

• GitHub - Milesight-IoT/SensorDecoders

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>