Milesight WT301 Smart Fan Coil Thermostat User Guide
- May 15, 2024
- Milesight
Table of Contents
User Guide Smart Fan Coil Thermostat
Featuring LoRaWAN®
WT30x
WT301 Smart Fan Coil Thermostat
Safety Precautions
Milesight will not shoulder responsibility for any loss or damage resulting
from not following the instructions of this operating guide.
- The device must not be disassembled or remodeled in any way.
- The device is not intended to be used as a reference sensor, and Milesight will not should responsibility for any damage which may result from inaccurate readings.
- Do not place the device where the temperature is below/above the operating range.
- Do not place the device close to objects with naked flames, heat source (such as oven), or exposure to sunlight, cold source, liquid, and extreme temperature changes.
- The device must never be subjected to shocks or impacts.
- Do not clean the device with detergents or solvents such as benzene or alcohol. To clean the device, wipe with a soft moistened cloth. Use another soft, dry cloth to wipe dry.
Declaration of Conformity
WT30x is in conformity with the essential requirements and other relevant
provisions of the CE and RoHS. Copyright © 2011-2023 Milesight. All rights
reserved.
All information in this guide is protected by copyright law. Whereby, no
organization or individual shall copy or reproduce the whole or part of this
user guide by any means without written authorization from Xiamen Milesight
IoT Co., Ltd. For assistance, please contact Milesight technical support:
Email: iot.support@milesight.com
Support Portal: support.milesight-iot.com
Tel: 86-592-5085280
Fax: 86-592-5023065
Address: Building C09, Software Park Phase III, Xiamen 361024, China
Revision History
Date | Doc Version | Description |
---|---|---|
Dec. 20, 2023 | V 1.0 | Initial version |
Product Introduction
1.1 Overview
WT301&WT302 is an advanced touch screen room thermostat specifically developed
to oversee fan and valve operations in air conditioner applications where fan
coil unit (FCU) is adopted. It achieves this by continuously comparing the
environmental temperature with the pre-set desired temperature, enabling both
proactive management and automatic control based on predefined logic. This
ensures optimal comfort and energy efficiency in the controlled environment.
With wireless detection and easy configuration, the WT301&WT302 offers
reliable and convenient room temperature arrangement optimization. It is
compatible with standard LoRaWAN® gateway, enabling real-time monitoring of
environmental status for effective remote management.
1.2 Key Features
- Adjust the room temperature automatically and manually with a time-controlled regulation
- Applicable for two pipes and 3-Speed fan coil system, compatible with On/Off relay (WT301) or 0-10V (WT302) valve control
- 5+1+1 six periods programmable maximize comfort and economy
- High accuracy of 0.5°C for temperature regulation, enabling precise control of indoor temperature levels
- Adopts an LCD screen with Four-color LED and capacitive touch buttons, providing a better interactive experience
- With clock display function
- With a 12cm ultra-thin embedded panel and a sleek, frameless design, it effortlessly blends into different interior styles, offering a minimalist and elegant appearance
- Equips with external NTC sensor signal input and keycard switch input
- Function well with standard LoRaWAN® gateways and network servers
- Easy to install with the compact size
- Highly adapt to different scenarios with 86mm hidden box and European 60mm round box
Hardware Introduction
2.1 Packing List If any of the above items are
missing or damaged, please contact your sales representative.
2.2 Hardware Overview Screen Descriptions:
Icon | Description |
---|---|
LoRaWAN® Network Status | Blinks: the network is de-activated |
Static On: the network is activated
2.3 Dimensions (mm)
Wiring Diagrams
-
WT301
AC95 – 240V – 50/60Hz -
WT302
AC95 – 240V – 50/60Hz
Installation
Installation Locations
It is suggested to install the WT30x thermostat about 5 ft. (1.5m) above the
floor in an area with good air circulation at average temperature.Do not install the device where:
- Close to hot or cold sources like hot or cold air ducts;
- The place in direct sunlight;
- Dead spots or drafts (behind the doors and in corners);
- In areas that do not require conditioning;
- lose to concealed chimneys or pipes;
- Close to metal objects and obstacles which affect the LoRaWAN® transmission;
- The place with lots of electromagnetic interfaces;
- The place where strong vibration may happen or easy to be subjected to physical shock.
Installation Steps
WT30x is suitable for installation within a standard 86mm pattress box or
European 60mm pattress box.
- Ensure the circuit of all related systems are shut off before installation.
- Connect corresponding wires to appropriate terminals of WT30x device.
- Remove LED screen from the mounting plate by pushing the LED screen assembly.
- Fix the mounting plate into the wall with mounting screws.
- Fix the LED screen back to the mounting plate.
Operation Guide
WT30x supports to configure device via 5 buttons. In the guide will use below names to indicate every button:
Button | Name |
---|---|
MODE | |
FAN | |
POWER | |
UP | |
DOWN |
5.1 Basic Settings
- Power On/off
Press “POWER” button to turn the thermostat on/off. When button lights green, the thermostat is off; when the power button is off, the thermostat is on.
Note:
- When the buttons are not pressed for more than 3 seconds, the LED screen will go off; please press the corresponding button configure the device as usual.
- Below operations only work when the thermostat is on.
-
Switch SystemMode
Press “MODE” button to switch the systemmode among HEATING, COOLING and VENTILATION.
In the mode of VENTILATION, the valve is off but the fan runs. -
Switch the Fan Speed
Press “FAN” button to switch the fan speed among AUTO, HIGH, MED, LOW. -
Adjust Manual & Programmable Mode
Operation: press and hold on “MODE” button →manual and programmable mode icons flashes by turns → loose “MODE” button → press “UP” button to select manual mode/ press “DOWN” button to select programmable mode. Icon| Mode| Description
---|---|---
| Manual| This mode supports to use “UP” and “DOWN” buttons to adjust target temperature manually.
| Programmable| This mode supports to control the temperature according to weekly programmable schedule. The “UP” and “DOWN” buttons will not work. -
Adjusting/Setting the Clock
Operation: press and hold on “MODE” button →manual and programmable mode icons flashes by turns → loose “MODE” button → press “MODE” button once to adjust minute of time → press “MODE” button once to adjust hour of time → press “MODE” button once to adjust weekday.
When you stop pressing the buttons for seconds, the device will save your settings automatically. -
Locking the Thermostat Buttons
Press and hold the “UP” and “DOWN” buttons together for 3 seconds to enable/disable button lock of your thermostat. When button lock is enabled, the lock icon will display. WT30x supports two lock modes: full lock and half lock. The lock mode can be set on advanced settings. -
Adjust the Weekly Programmable Schedule
WT30x supports to add up to 6 time periods and 6 temperature values during weekdays, Saturday or Sunday.
Operation: press and hold on “MODE” button →manual and programmable mode icons flashes by turns → loose “MODE” button → press “MODE” button 4 times → press “UP” and “DOWN” button to adjust weekday-period 1 time → press “UP” and “DOWN” button to adjust weekday-period 1 temperature → press “UP” and “DOWN” button to adjust weekday-period 2 time → ……..
After completing all settings, click “MODE” button to confirm and exit the
schedule settings.
Besides, when you stop pressing any button for a few seconds, the device will
save your settings and exit the schedule setting mode.
Default settings of programmable schedules are as follows:
Time Display | Weekday (Mon. to Fri.) | Saturday | Sunday |
---|---|---|---|
Time | Temperature | Time | Temperature |
Temperature
Period 1| 06:00| 20°C| 06:00| 20°C| 06:00| 20°C
Period 2| 08:00| 15°C| 08:00| 20°C| 08:00| 20°C
Period 3| 11:30| 15°C| 11:30| 20°C| 11:30| 20°C
Period 4| 13:30| 15°C| 13:30| 20°C| 13:30| 20°C
Period 5| 17:00| 22°C| 17:00| 20°C| 17:00| 20°C
Period 6| 22:00| 15°C| 22:00| 15°C| 22:00| 15°C
5.2 Advanced Settings
Press the “POWER” button to turn off the thermostat, then press and hold on
“MODE” and “FAN” buttons together for 5 seconds to reach advanced settings.
After completing all settings, press “MODE” button to confirm and exit.
Besides, when you stop pressing the button, the device will save your settings
after a few seconds automatically and exit the advanced settings. These
advanced settings will take effect after turning on the thermostat.
Code | Function | Settings and Options | Default |
---|---|---|---|
1 | Temperature Compensation (Calibration) | -9°C~9°C, add this value to room | |
temp. | -3°C | ||
2 | Fan Control | 00: When room temp. reaches the set temp., the fan will turn |
off 01: When room temp. reaches the set temp., the fan will keep low speed
running| 00
3| Button Lock| 00: half lock, all buttons are locked except “POWER” button
01: full lock, all buttons are locked| 01
4| System Mode
Selection| 00: Cooling/Ventilation
01: Cooling/Heating/Ventilation| 01
5| Min. Set Temp.| 5°C~15°C (for “DOWN” button)| 5°C
6| Max. Set Temp.| 15°C~35°C (for “UP” button)| 35°C
7| Time Mode| 00: 12-Hour-Clock
01: 24-Hour-Clock| 01
8| Display Mode| 00: Display both set temp. and room temp.
01: Display set temp. only| 00
9| Keycard Function (when keycard is no connected)| 00: Energy saving(ECO)
mode: goes to energy saving temp. 01: Standby: the fan and valve relay all
off| 00
10| Keycard heating energy-saving temperature| 10°C~30°C| 20°C
11| Keycard cooling energy-saving temperature| 10°C~30°C| 26°C
12| Daytime display brightness| 0-8
Note: The daytime is the time between period 1 and period 6 of weekly
schedule, the default is 6:00~22:00.| 3
13| Night display brightness| 0-8| 1
| (Set Temp. Tolerance)| The valve will start cooling when room temp. > (set
temp. + dead zone temp.); start heating when room temp. < (set temp. – dead
zone temp.).|
---|---|---|---
15| Report Interval| 1~60 minutes| 1 minute
16| LoRaWAN® Mode| 00: SerialNet
01: AT MODE| 00
17| Keycard Function| 00: On
01: Off| 01
18| Time Zone| 0~24: the corresponding time zone -12~12
12 means time zone is UTC+0| 12
19| Room Temp.
Sensor| 00: Use internal NTC or external NTC input sensor
01: Use external temperature data via downlink command| 00
20| Version Number| | U9
WT302 Only
14 | Report Interval | 1~60 minutes | 1 minute |
---|---|---|---|
15 | P Value | 1-10 | 2 |
16 | I Value | 1-60s | 40s |
17 | LoRaWAN® Mode | 00: SerialNet | |
01: AT MODE | 00 | ||
18 | Keycard Function | 00: On | |
01: Off | 01 | ||
19 | Time Zone | 0~24: the corresponding time zone -12~12 | |
12 means time zone is UTC+0 | 12 | ||
20 | Room Temp. | ||
Sensor | 00: Use internal NTC or external NTC input sensor | ||
01: Use external temperature data via downlink command | 00 | ||
21 | Version Number | U9 |
Definition of P Value
The proportional band is the amount of change required by the ambient
temperature for the output to go from 0 to 100%. It can be adjusted from 1~10.
Factory default is 2.
The larger the P value, the greater the change in valve output; the smaller
the P value, the smaller the change in valve output.
For example, when P=2, the temperature difference between ambient temperature
and setpoint is 5°C, the valve will open about 10%; when P=4, the temperature
difference between ambient temperature and setpoint is 5°C, the valve will
open 20%.
Heat mode (P-band: 2)
When the ambient temperature is below the set point the output is somewhere
between 0~100%. Cool mode (P-band: 2)
When the ambient temperature is above the set point the output is somewhere
between 0~100%. Definition of I Value
This feature allows you to set the integral action time for the integral to
run from 0 to 100%. The value required depends on the reaction time of the
control loop. If the time is chosen too short, the control loop will become
instable and oscillate. If the time is chosen too long, the control loop will
become sluggish. It can be adjusted from 1s-60s. The default value is 40s.
5.3 LoRaWAN® Settings
WT30x does not support to configure LoRaWAN® information. Please contact
Milesight to customize the LoRaWAN® settings before purchase.
Parameters | Description | Default |
---|---|---|
Device EUI | Unique ID of the device. | On the label |
App EUI | The default App EUI is 24E124C0002A0001. | 24E124C0002A0001 |
Application Port | The port is used for sending and receiving data. | 85 |
Join Type | OTAA and ABP modes are available. | OTAA |
Application Key | Appkey for OTAA mode. | 5572404C696E6B4C6F 52613230313823 |
--- | --- | --- |
Network Session Key | Nwkskey for ABP mode. | |
Application Session Key | Appskey for ABP mode. | |
Device Address | DevAddr for ABP mode. | Last 8 digits of Device EUI |
LoRaWAN® Version | LoRaWAN® protocol version. | V1.0.3 |
Work Mode | It’s fixed as Class C. | Class C |
RX2 Data Rate | RX2 data rate to receive downlinks. | See appendix |
RX2 Frequency | RX2 frequency to receive downlinks. | See appendix |
Confirmed Mode | If the device does not receive an ACK packet from the network | |
server, it will resend data once. | Off | |
ADR Mode | Allow network server to adjust data rate of the device. | On |
Spread Factor | If ADR is disabled, the device will send data via this spread | |
factor. | See appendix | |
Tx Power | Transmit power of the device. | SF9 |
Communication Protocol
6.1 Device Data
All data are based on following format (HEX):
Start | ID | Data Length | Data | Checksum |
---|---|---|---|---|
55 | 01 | 2 Bytes | 2 Bytes or 10 Bytes | 1 Byte |
The Data part is consist of Type ID (1 Byte) and Data Content (1 Byte or 9 Bytes) :
Item | Type | Data & Description |
---|---|---|
Turn On/Off | 01 | 00: Off, 01: On |
Button Lock | 02 | 01: Enable, 00: Disable |
System Mode | 03 | 00: Cooling, 01: Heating, 02: Ventilation |
Fan Mode | 04 | 00: Auto, 01: High, 02: Middle, 03: Low |
Room Temperature | 05 | INT8/2, Unit: °C |
Set Temperature | 06 | INT8/2, Unit: °C |
--- | --- | --- |
Keycard Status | 07 | 00: Disconnected, 01: Connected |
Configuration Mode | 08 | 00: Programme, 01: Manual |
External Server Temperature | 09 | INT8/2, Unit: °C |
All Data | 0f | Reports all above data in order |
Examples:
- Periodic packet: report as reporting interval (1 minute by default) or when pressing the button to change the settings.
55 01 000a 0f 01000001332a000034 02
Start| ID| Data Length| Data Type| Data Content|
Checksum
55| 01| 00 0a=10 Bytes| 0f| 01=Turn On 00=Button Lock Disable
00=Cooling 01=High
33=>51/2=25.5°C (Room Temp.)
2a=>42/2=21°C (Set Temp.) 00=Keycard is disconnected 00=Programme Mode
34=>52/2=26°C (External Temp.)| 02
6.2 Downlink Control Commands
WT30x supports downlink commands to configure the device. The application port
is 85 by default. The command is based on following format (HEX):
Start | ID | Command Length | Command | Checksum |
---|---|---|---|---|
55 | 01 | 2 Bytes | 2 Bytes or 8 Bytes | 1 Byte |
The Command part is consist of Type ID (1 Byte) and Command Content (1 Byte or 7 Bytes) :
Item | Type | Command & Description |
---|---|---|
Turn On/Off | 01 | 00: Off, 01: On |
Button Lock | 02 | 01: Enable, 00: Disable |
System Mode | 03 | 00: Cooling, 01: Heating, 02: Ventilation |
Fan Mode | 04 | 00: Auto, 01: High, 02: Middle, 03: Low |
Set Temperature | 05 | INT8/2, Unit: °C |
Configuration Mode | 06 | 00: Programme, 01: Manual |
External Server Temperature | 07 | INT8/2, Unit: °C |
Note: this only takes effect when advanced setting-Room Temp. Sensor is set as
- ---|---|---
All Commands| 0f| Send all above commands in order
Checksum Calculation: sum of bytes % 256
Examples:
- Turn on the device.
55 01 0002 0101 5a
Start| ID| Command Length| Data Type| Command| Checksum
55| 01| 00 02=2 Bytes| 01| 01=Turn On| 5a
2. Set all configurations:
55 01 0008 0f 010000012a0034 cd
Start| ID| Data Length| Data Type| Command|
Checksum
55| 01| 00 08=8 Bytes| 0f| 01=Turn On 00=Button Lock Disable
00=Cooling 01=High
2a=>42/2=21°C (Set Temp.) 00=Programme Mode
34=>52/2=26°C (External Temp.)| cd
6.3 Downlink Enquiry Commands
WT30x supports downlink commands to enquiry the device information. The
application port is 85 by default. The command is based on following format
(HEX):
Start | ID | Command Length | Data Type | Checksum |
---|---|---|---|---|
55 | 02 | 0001 | 1 Byte | 1 Byte |
Item | Data Type | Checksum | ||
--- | --- | --- | ||
Turn On/Off | 01 | 59 | ||
Button Lock | 02 | 5a | ||
System Mode | 03 | 5b | ||
Fan Mode | 04 | 5c | ||
Room Temperature | 05 | 5d | ||
Set Temperature | 06 | 5e | ||
--- | --- | --- | ||
Keycard Status | 07 | 5f | ||
Configuration Mode | 08 | 60 | ||
External Server Temperature | 09 | 61 | ||
All Data | 0f | 67 |
Examples:
- Enquiry the room temperature.
55 02 0001 05 5d
Start| ID| Data Length| Data Type| Checksum
55| 02| 00 01=1 Byte| 05=Room Temperature| 5d
Reply:
55 01 0002 05 33 90
Start| ID| Data Length| Data Type| Data Content| Checksum
55| 01| 00 02=2 Bytes| 05| 33=>51/2=25.5°C| 90
2. Enquiry all data.
55 02 0001 0f 67
Start| ID| Data Length| Enquiry Type| Checksum
55| 02| 00 01=1 Byte| 0f=All data| 67
Reply: the same as periodic packet.
Appendix
Default Frequency
Supported Freq | Channel/MHz |
---|---|
CN470 | 471.9, 472.1, 472.3, 472.5, 472.7,472.9, 473.1, 473.3 (8~15) |
EU868 | 868.1, 868.3, 868.5 |
IN865 | 865.0625, 865.4025, 865.985 |
RU864 | 868.9, 869.1 |
AU915 | 916.8, 917, 917.2, 917.4, 917.6, 917.8, 918, 918.2 (8~15) |
US915 | 903.9, 904.1, 904.3, 904.5, 904.7, 904.9,905.1, 905.3 (8~15) |
KR920 | 922.1, 922.3, 922.5 |
AS923-1 | 923.2, 923.4 |
--- | --- |
AS923-2 | 921.4, 921.6 |
AS923-3 | 916.6, 916.8 |
AS923-4 | 917.3, 917.5 |
Default RX2 Frequency and Datarate
Supported Freq | RX2 Frequency & Datarate |
---|---|
CN470 | 505.3MHz, DR0 (SF12, 125k) |
EU868 | 869.525MHz, DR0 (SF12, 125k) |
IN865 | 866.55MHz, DR2 (SF10, 125k) |
RU864 | 869.1MHz, DR0 (SF12, 125k) |
AU915 | 923.3MHz, DR8 (SF12, 500k) |
US915 | 923.3MHz, DR0 (SF12, 500k) |
KR920 | 921.9MHz, DR0 (SF12, 125k) |
AS923-1 | 923.2MHz, DR2 (SF10, 125k) |
AS923-2 | 921.4MHz, DR2 (SF10, 125k) |
AS923-3 | 916.6MHz, DR2 (SF10, 125k) |
AS923-4 | 917.3MHz, DR2 (SF10, 125k) |
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>