KAISER BAAS KBA13113 S1 Single Axis Gimbal User Manual
- June 7, 2024
- Kaiser Baas
Table of Contents
- SAFETY PRECAUTIONS
- IMPORTANT BATTERY SAFETY INFORMATION
- PRODUCT DIAGRAM
- PRODUCT DIAGRAM
- CHARGING YOUR S1 GIMBAL
- CHARGING THE BATTERY IN YOUR REMOTE CONTROL
- TO TURN ON/OFF THE GIMBAL
- TO TURN ON/OFF THE REMOTE CONTROL
- SETTING UP YOUR REMOTE CONTROL
- CONNECTING THE REMOTE CONTROL TO YOUR PHONE
- SETTING UP YOUR Si GIMBAL
- USING GIMBAL MODE
- SWITCHING BETWEEN PORTRAIT AND LANDSCAPE MODE
- USING YOUR Si AS A SELFIE STICK
- USING THE TRIPOD
- SPECIFICATION
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KAISER BAAS KBA13113 S1 Single Axis Gimbal User Manual
SAFETY PRECAUTIONS
Before using your Kaiser Baas SI Gimbal Please ensure you read and understand the following product and safety precautions.
- Dropping or otherwise impacting the gamble may damage the product causing a to malfunction.
- Ensure there is nothing obstructing the Gimbal wren the SI Is powering on.
- The Si Gimbal is not water resistant. Do not use any liquid cleansers. Only use a soft dry cloth to clean the SI.
- Keep the Si away from sand and dust to safeguard the sensors In the motors.
- ONLY recharge the SI using the supplied USB cable: If using a wall charger, ensure that it is a certified product for your region. AC Input: i CO-240VAC 50/60Hz. CC Output. 5V Only use a USB wall charger with suitable approval and certification. Do not charge in conchtions outside of the 10°C – 45C range. If you do not know the voltage and current of your charger. use the Included cable to charge from you’ computer.
- The Gimbal should not be used in heal exceeding 55C (131`e).
- DO NOT drop. crush. pierce. bend. delorm, microwave. incinerate or damage the Gimbal.
IMPORTANT BATTERY SAFETY INFORMATION
- DO NOT use any third-party or unknown accessories or batteries.
- DO NOT disassemble the battery.
- DO NOT short-circuit the battery. Short circuiting may occur when the battery touches other motel objects.
- DO NOT charge the battery n direct sunlight.
- Always charge the battery in a designated space. away from people and animals.
- DO NOT leave a battery on prolonged charge when not in use.
- It the battery has a Non surface temperature, leave d to cool before no try to re-cterge it.
- DO NOT charge the battery it the ambient temperature is below 10’C or above 45^C.
- Always use the supplied charger and observe manufacturer charging requirements.
- Battery performance is best when within normal room temperature (5t-20t1).
- Batteries need to be charged before use.
PRODUCT DIAGRAM
PRODUCT DIAGRAM
- Micro USB charging port
- Positioning bead
- Phone clip
- Gimbal status indicator
- Gimbal power button
- Rotation lock
- Extend pole
- Capture/record button
- Bluetooth remote indicator
- Tripod grip
CHARGING YOUR S1 GIMBAL
Charge your gimbal using the Micro USB cable supplied. Once the Si has
finished charging the red LED indicator will turn off and the green LED
indicator light will turn on.
CHARGING THE BATTERY IN YOUR REMOTE CONTROL
if you find it challenging opening the remote simply slot a strong slim object into the side slot on the remote and carefully twist.
TO TURN ON/OFF THE GIMBAL
To power ON / OFF the Gimbal, press and hold the power button 5 for few seconds.
TO TURN ON/OFF THE REMOTE CONTROL
To power ON / OFF the Remote Control, press and hold the power button 8 for few seconds.
SETTING UP YOUR REMOTE CONTROL
Pull out the battery insulter from the remote control.
CONNECTING THE REMOTE CONTROL TO YOUR PHONE
- Turn on the remote control by pushing the power button for 3 seconds until the blue LED light flashes.
- Turn on Bluetooth via Settings on your smartphone. Search and connect to KB-BT.
SETTING UP YOUR Si GIMBAL
- Unfold the gimbal and tighten the rotation lock.
- Open the Phone Clip and place your smartphone in the holder. Move and adjust the positioning until the phone is centered and balanced.
Note; If the gamble is not well-balanced and turned on it could cause overheating or excessive power consumption.
USING GIMBAL MODE
The S1 one can be used with or without Gimbal mode turned on. To turn on
gimbal mode rotate the gimbal unit clockwise so it isn’t clipped to the
Positioning Bead. Press the Gimbal Power Button 5 for 3 seconds to turn on the
gimbal function.
Take photos or videos using either your camera or the remote control if you have connected it.
SWITCHING BETWEEN PORTRAIT AND LANDSCAPE MODE
To switch between portrait or landscape simply click the Gimbal Power Button 5
and it will switch between vertical mode and landscape mode.
USING YOUR Si AS A SELFIE STICK
When the gimbal function is turned off turn the body of the gimbal around
until it locks into the positioning bead and it can then be used as a selfie
stick.
USING THE TRIPOD
Open the three tripod legs and place it on a horizontal table. Adjust the
overall center of gravity depending on phone positioning to avoid tilting.
SPECIFICATION
Payload:
300g
Net Weight:
230g
Battery Capacity
Lio-ion 400mAh
Charging Port:
Micro USB
Charging Voltage:
5V
Operating Current:
50mA – 900mA
Operating Time:
2 – 3 Hours
Charging Time
: 2 Hours
Bluetooth Remote Range:
10m
Bluetooth Remote Battery Type:
CR1620
Product Size:
19010’40mm
Extended Length:
592mm
SUPPORT
Having trouble with your Gimbal?
Don’t worry. our friendly support team can help. Please visit us at:
www.kaiserbaas.com/supporl Or send us an
email at: helpdeskRkaiserbaas.com
FAO
Q: My remote control isn’t working?
A: The remote control MI go into sleep mode alter 10 minutes of no operatic”
Simply clip the remote control capture button to wake it up. II this doesn’t
work your battery may need replacing.
Q: The remote control is showing a red LED.
A: When the remote control battery ex low the red LED light turns on.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>