Aerpro APMSMG1 Dash and Vent Mount Magnetic Holder User Manual

Aerpro APMSMG1 Dash and Vent Mount Magnetic Holder

Product Information

The APMSMG1 Dash & Vent Mount is a magnetic holder designed for use with MagSafe Compatible iPhones and cases. It features a charging contact, magnetic head, alignment magnet, adhesive mount, hook clip fixing plate, and an adjustable collar. The magnets ensure proper alignment for fast wireless charging.

Compatible devices include iPhone 12 and onwards.

Product Usage Instructions

Attaching the mount to the holder

1. Place the adjustable collar over the ball of the mount.
2. Press the ball of the mount into the back of the magnetic head.
3. Move the magnetic head to the desired position and tighten the adjustable collar.

Attaching the adhesive mount to a flat surface

1. Clean any oil, debris, or dust on the area where 3M base is to be placed. If possible, use an alcohol wipe to help with adhesion.
2. Peel off the protection sheet from the 3M base and stick it to the chosen area by strongly pressing the base for an extended period of time.
3. The strength of the 3M tape will perform perfectly after 4-5 hours of installation. Do not use the magnetic holder during this period or the mount may become unstuck.

Attaching the hook mount to a vent

1. Unfasten the hook clip sufficiently by rotating the fixing plate.
2. Insert the hook clip to the center of the vents.
3. Rotate the adjustable collar so that the fixing plate tightens against the hook to avoid the presence of any gap between the fixing plate and vent.
4. Check if the vent clip is fixed firmly and correctly.

CAUTION: The Vent Mount is designed to be used only with FLAT air vent blades.

Inclusions:

• Magnetic head
• Vent mount
• Adhesive mount

For more information, please visit www.aerpro.com.

Device Compatibility

This product is designed for use with MagSafe Compatible iPhones and cases.
On supported models, MagSafe charging magnetic holders snap to the back of an iPhone or its MagSafe case or sleeve.
The magnets ensure proper alignment for fast wireless charging.
Compatible devices include iPhone 12 and onwards.

Product Information

Attaching the mount to the holder

1. Place the adjustable collar over the ball of the mount
2. Press the ball of the mount into the back of the magnetic head
3. Move the magnetic head to the desired position and tighten the adjustable collar.

Attaching the adhesive mount to a flat surface

1. Clean any oil, debris, or dust on the area where 3M base is to be placed. If possible use an alcohol wipe to help with adhesion.
2. Peel off the protection sheet from the 3M base and stick to chosen area by strongly pressing the base for an extended period of time.
3. The strength of the 3M tape will perform perfectly after 4-5 hours of installation.
4. Do not use the magnetic holder for the above period of time or the mount may become unstuck.

Attaching the hook mount to a vent

1. Unfasten the hook clip sufficiently by rotating the fixing plate.
2. Insert the hook clip to the center of the vents
3. Rotate the adjustable collar so that the fixing plate tightens against the hook to avoid the presence of any gap between fixing plate and vent.
4. Check if vent clip is fixed firmly and correctly.

The Vent Mount is designed to be used only *with FLAT air vent blades.

CAUTION

1. The magnet used in this product will have no negative impact on the phone. In case of any applications not working correctly, please restart application and slightly adjust the position of where smartphone is mounted.
2. Never mount a smartphone onto holder with a magnetic credit card in the smartphone case.
3. Be careful not to have the magnet be in reach of medical devices.
4. Periodically check the tightness of the hook vent clip to prevent unexpected dropping of phone.
5. When removing your smartphone from the magnetic holder, twist and slide, rather than pulling off directly. This will help protect the vent blades from being removed or damaged due to the extreme strength of the magnets.
6. Do not install the holder where it will obstruct the drivers view.
7. Periodically check the strength of the 3M base.
8. Do not operate phone and holder while driving.

Inclusions

• Magnetic head
• Vent mount
• Adhesive mount

Technical assistance

If you need assistance with your Aerpro product call Aerpro Support Australia.
TEL: 03 – 8587 8898
FAX: 03 – 8587 8866 Mon-Fri 9am – 5pm AEST
This manual is considered correct at time of writing but is subject to change. For latest manuals and updates refer to the website.

www.aerpro.com

References

• Home | Aerpro
• Home | Aerpro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>