Westinghouse SR07PM04H-41 Solar LED Path Light with Motion Sensor User Manual
- June 12, 2024
- Westinghouse
Table of Contents
Westinghouse SR07PM04H-41 Solar LED Path Light with Motion Sensor
Product Information
- Product Name: Solar LED Path Light with Motion Sensor
- Model Number: SR07PM04H-41
- Parts Included: Solar Panel (A), Pole 1 (B), Pole 2 (C), Ground Stake (D)
- Power Source: Solar energy
- Battery Type: 3.7V, 800 mAh lithium (14500) rechargeable battery
- Motion Sensor: Yes
Product Usage Instructions
- For the first time use, follow these steps:
- Place the solar lights in direct sunlight for 8-12 hours to fully charge the battery.
- Ensure the power switch is in the ON position.
- Assembly:
- Insert the solar panel (Part A) into Pole 1 (Part B).
- Insert Pole 1 (Part B) into Pole 2 (Part C).
- Pull out the Ground Stake (Part D) from the bottom of Pole 2 (Part C) and plug it back into Pole 2 (Part C).
- Apply pressure to the pole and carefully insert the complete assembly (Part A, B & C) into the ground at the desired location.
- Note: If the ground is hard and packed, moisten it with water before inserting the stake to avoid breakage.
- Troubleshooting:
- If the light doesn’t turn on, remove the battery and wipe both ends with a clean, dry cloth. Reinstall the battery.
- Check the battery to ensure it is making secure contact with the terminals.
- If the above steps don’t work, replace the battery with a new 3.7V, 800 mAh lithium (14500) rechargeable battery.
- Replacing the Battery:
- Slide the power switch to the OFF position.
- Use a Phillips head screwdriver to remove the 3 screws holding the base in place.
- Replace the old battery with a new 3.7V, 800 mAh lithium (14500) rechargeable battery.
- Align the base properly and replace the 3 screws removed earlier.
- Slide the power switch to the ON position.
- For optimal performance, place the fixture in sunlight for 8-12 hours with the power switch in the ON position to fully charge the battery.
FCC Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
FCC Warning (Spanish):
ADVERTENCIA DE LA FCC: Este dispositivo cumple con la Parte 15 de las
Reglas de la FCC. Su funcionamiento está sujeto a las siguientes dos
condiciones:
Battery Disposal Warning:
Do not dispose of lithium batteries in the municipal waste stream or by
fire as batteries may explode. Do not open, short circuit, or destroy
batteries. Dispose of batteries in accordance with Local, State, and Federal
regulations. Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride, or
lithium ion) batteries.
Trademark Information:
“Westinghouse” is a trademark of Westinghouse Electric Corporation. Used
under license by Sky Rich Star Limited. All Rights Reserved.
INSTRUCTIONS
FOR FIRST TIME USE : Solar lights need to charge in full sunlight for 8 – 12 hours in direct sunlight, with the power switch in the “ON” position, to fully charge the battery.
NOTE: The solar lights will stay on for 30 seconds when triggered by motion delivering up to 400 lumens and revert back to standby mode delivering up to 20 lumens until motion is detected. The solar lights use radio frequency technology to link. The solar lights should not be greater than 65.6 feet (20 m) apart for linked function to work properly. When one solar light is triggered by motion, all lights will activate and deliver up to 400 lumens. The package includes (4) solar lights. These (4) solar lights are factory linked, and can not be linked with more of the same type light or any other lights.
NOTE: If there are performance or quality issues, all solar lights need to be replaced with another set.
ASSEMBLY
Insert the solar panel (Part A) into the pole 1 (PartB), Insert the pole 1
(PartB) into the pole 2 (Part C), pull out the ground stake (Part D) at the
bottom of the pole 2 (Part C) and plug it back into the the pole 2 (Part C).
Applying pressure to the pole, carefully insert the complete assembly (Part A,
B & C) into the ground where desired.
NOTE: If the ground is hard and packed, moisten the ground with water
before inserting the stake to
avoid breakage.
TROUBLESHOOTING
If light doesn’t turn on, remove battery, wipe both ends with a clean, dry
cloth and reinstall battery. Check the battery to ensure that it is making
secure contact with the terminals. If this doesn’t work, replace with new
battery.
REPLACING THE BATTERY
Slide the power switch to the “OFF” position. Use a Phillips head screwdriver
to remove the 3 screws holding the base in place. Replace old battery with a
new 3.7V, 800 mAh lithium (14500) rechargeable battery. Replace the base by
aligning it properly and replacing the 3 screws removed earlier. Slide the
power switch to the “ON” position.
For optimal performance, place fixture in sunlight for 8-12 hours, with power
switch in the “ON” position, to fully charge battery.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
FCC WARNING
- This device may not cause harmful interference, and
- Tthis device must accept any interference received, including interference that may cause undesired operation.
Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no quarantine that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
WARNING: Do not dispose of lithium batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries .
For additional help and information regarding installation, contact Customer Service at 1-844-551-0680, 8am-5pm,CST Monday – Friday customerservice@idctexas.com
and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>