roomfitters FOMO-CRDZ-002-V1 Mid Century Buffet Cabinet Instruction Manual

roomfitters FOMO-CRDZ-002-V1 Mid Century Buffet Cabinet

Important Information

THE PRODUCT MAY RECOMMENDED ASSEMBLING BY MORE THAN ONE PERSON.

PLEASE ASK FOR ASSISTANCE AT YOUR CONVENIENCE BEFORE ASSEMBLING.

Before You Start

• Read through each step carefully and follow the proper order
• Separate and count all your parts and hardware
• Give yourself enough room for the assembly process
• Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer
• Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight.
  Failure to do so may result in stripping the screw.

Cam Lock Fastening System

This Cam Lock Fastening System will be used throughout the assembly process.

Parts Identification

• A

TOP

• B

BOTTOM

• C

MOVABLE SHELVES x 2

• D

LEFT

• E

MIDDLE SHELF

• F

RIGHT

• G

BACK PANEL

• H

LEFT DOOR

• I

RIGHT DOOR

• J

RIGHT AND LEFT END x

• K

RAILS x 2

Hardware Identification

1. SCREW QTY: 11+1 spare

2. WOOD DOWEL QTY: 22+1 spare

3. CAM BOLT QTY: 13+1 spare

4. CAM LOCK QTY: 6+1 spare

5. SCREW QTY:28+1spare

6. SHEIF SUPPORT QTY:8+1spare

7. EUROPE HINGE QTY:4

8. HEX KEY QTY:1

9. BOLT QTY:8+1spare

10. BOLT QTY: 8+1 spare

11. DOOR TOUCH LATCH QTY:2

12. TIPPING RESTRAINT HARDWARE KIT QTY:1

13. CAM LOCK QTY: 7+1 spare

Assembly Instructions

• Step 1
  

• Step 2
  

• Step 3
  

• Step 4
  

• Step 5
  

• Step 6
  

• Step 7
  

• Step 8
  

• Step 9
  

• Step 10
  

• Step 11
  

• Step 12
  

To adjust the vertical height.
Loosen the four screws “A” on both hinges. Two of them are usually in slotted holes which allows you to adjust up or down by a few mm. Then tighten back up.

To adjust depth.
Loosen screw “B” and adjust door, if the door can not be adjusted, please loosen screw “C”, then try again. Tighten screw “B” and “C”.

To adjust side ways.
Turning the screw “C” on BOTH hinges on each door.

• Step 13
  

• Step 14

• Step 15
  PART LIST| FIGURE| QUANTITY| DESCRIPTION
  ---|---|---|---
  12.1|

| 2PC| LONG SCREW
(Dia.4mmX38mmL)
12.2|

| 2PC| SHORT SCREW
(Dia.4mmX19mmL)
12.3|

| 4PC| METAL “L”BRAKET
12.4|

| 2PC| PLASTIC ANCHOR
12.5|

| 2PC| CABLE

Follow the instructions printed on the plastic bag containing the tipping restraint hardware to attach the tip-over restraints to the unit and the wall.
NOTE: The tipping restraint hardware included is for drywall construction. It will be necessary to drill holes for the wall anchors. Depending upon your wall construction, different anchor hardware maybe required.
Please contact your local hardware store for assistance.

YOU CAN MAKE GAP ADJUSTMENT WHEN DOORS DOES NOT OPEN CORRECTLY OR SMOOTHLY BY POP OUT THE EJECTOR PIN AND ROATE IT OUT TO THE PROPER LENGTH.

Safety Maximum Loads

This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury.

WARNING
Please make sure that all objects are removed before moving the assembled unit.
The unit must be team lifted, not dragged or pushed. Failure to do so could cause instability, product collapse, and/or serious injury.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>