iottie C1F1tFNEqZL Car Charger Easy One Touch Wireless 2 User Guide
- June 12, 2024
- iOttie
Table of Contents
iottie C1F1tFNEqZL Car Charger Easy One Touch Wireless 2
Getting Started
For optimal mounting and charging, please follow the detailed instructions
within this manual when using the Easy One Touch
Wireless 2 Charging Mount. iOttie is not liable for possible damages due to
product misuse.
Critical Information
-
o Compatibility
Google, Apple & Samsung Wireless Fast Charge Compatible. The Easy One Touch Wireless 2 delivers wireless fast charging to all Qi enabled smart phones (Qi speed dependent on phone make and model) -
Qi Wireless Charging in Vehicle
Use the included iOttie Car Charger and Micro USB Cable. If you do use a third party car charger, use a Qualcomm Quick Charge 2.0 or equivalent adapter to receive a wireless charge (with compatible devices). -
The Easy One Touch Wireless 2 Charging mount’s signal could possibly interfere with your TPMS (tire pressure monitoring system).
If you notice that your TPMS light turns on, please try to use your mount in different locations to avoid the signals from interacting.
Telescopic Arm extends from 5 inches to 7 inches.
To reuse Suction Cup, simply rinse under warm water and let air dry to restore
tacky suction.
At a Glance
Qi Alignment Guide
The Qi Receiver Coil is usually located in the center area of the phone.
Check with your phone’s manufacturer for Qi coil location. Below are some
examples for commonly used phones.
For optimal wireless charging, please make sure your smartphone and mount’s Qi coils are aligned.
Alignment & Connecting to Power
Foot Release Button
The Foot can be adjusted to 3 different height settings to accommodate
different phone sizes, once setup is chosen, the foot is designed to align
with the center of the side arms for optimal Qi Wireless charging.
Cradle Knob
When mounting in landscape mode, loosen to rotate the Cradle. Tighten to lock
in desired position.
The Easy One Touch Wireless 2 is powered via a micro-USB cable. There is no on/off switch on the device. Once it is plugged in, the device will remain on unless the vehicle shuts off power when in parking mode.
Installation
Assembling the Mount
A. Connect the Mount Cradle with the Ball Joint.
B. Then, tighten the Cradle Knob.
Selecting a Location
Choose an installation method: Dashboard/Flat Surface (A) or Windshield/Curved Glass (B).
Option A
Dashboard or Flat Surface Installation
Choose an area on a flat surface on the vehicle’s dashboard and wipe any dust
or debris from the surface.
-
Peel off the film on the dashboard pad & stick on the desired installation location.
-
Peel off the protective film on the Suction Cup and press mount firmly onto the dashboard pad.
-
Push Locking Lever down to engage suction.
Option B
Windshield Installation or Curved Glass Installation
Choose a location on the windshield and wipe any dust or debris from the
surface.
-
Peel off the protective film on the Suction Cup and press firmly onto the windshield.
-
Push Locking Lever down to engage suction.
Adjusting the Mount
Telescopic Knob
Located on top of Telescopic Arm, loosen to extend the arm, and tighten to
secure distance.
Pivot Knob
Located on the side of the Mount Base, turning allows you to pivot telescopic
arm. Tighten to secure position.
Using the Easy One Touch Mechanism
The Easy One Touch lock and release mechanism makes it simple to mount & retrieve smartphones in seconds.
Mounting
-
Press the locking side arms in.
-
Press your device against the Easy One Touch trigger button. The mount’s arms will automatically close on contact and hold the device during the driving journey.
Releasing
Press the locking side arms with one hand and retrieve the device.
Wireless Charger Specifications
INPUT | DC 5V-3A 9V – 2A 12V-1.5A |
---|---|
CHARGING PORT | MICRO USB |
LENGTH | 4.3″ |
WIDTH | 2.4″ |
HEIGHT | 4.5″ |
WEIGHT | 3.6 oz |
Car Charger Specifications
INPUT | 12VN24V |
---|---|
OUTPUT | DC 5V – 3A 9V-2A 12V-1.5A |
Charging Indicator
Solid Green Light | Smartphone charging . |
---|---|
Blinking Red Light | Smartphone not charging. |
Foreign object detected or overheat ing of mount or smart phone .
Declaration of Conformity (FCC)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. You can refer to the following completed FCC warnings.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received,
including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 1 5 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operational Warnings
During the charging process, the transfer of electricity gives off heat. Your
device may become warm, but should not become exceedingly hot.
If the device gets wet, please cease charging immediately. Remove all plugs
and dry the product completely. Device is only to be operated in adry, indoor
environment.
Please be careful of excessive drops, dents, punctures, or deformities on the
device. If you are concerned, please unplug the device and contact the
manufacturer.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Operating this device in a hot environment or in direct sunlight for a long
period of time may cause malfunctions. We recommend keeping the product in
cooler temperatures.
Please use included components for an optimal experience. To support Qi
wireless charge when using a third party car charger or a USB Power Adapter
use a minimum output of both “9.0V-1.67 A or 5.0V-2.0t,:.’ and at least QC
2.0.
The product’s signal could possibly interfere with you TPMS (tire pressure
monitoring system). If you notice that your TPMS light turns on, please try
using your mount in different locations to avoid the signals from interfering
with each other.
California Proposition 65 this product contains chemicals known to the state
of California to cause cancer and birth defects or other reproductive harm
CAUTION
OLD ELECTRICAL APPLIANCES MUST NOT BE DISPOSED OF TOGETHER WITH THE RESIDUAL
WASTE, BUT HAVE TO BE DISPOSED OF SEPARATELY.
If you love your iOttie product, let us know by leaving a review online, or connect with us on our social platforms.
Customer Support
20 W 37th St
New York, NY 10018
U.S.A.
www.iottie.com
cs@iottie.com
Documents / Resources
|
iottie C1F1tFNEqZL Car Charger Easy One Touch Wireless
2
[pdf] User Guide
C1F1tFNEqZL, C1F1tFNEqZL Car Charger Easy One Touch Wireless 2, Car Charger
Easy One Touch Wireless 2, Charger Easy One Touch Wireless 2, Easy One Touch
Wireless 2, Touch Wireless 2, Wireless 2
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>