ORTECH OD-UGB201A LED Landscape Lighting Adjustable Inground Light Instruction Manual

ORTECH OD-UGB201A LED Landscape Lighting Adjustable Inground Light

LED Landscape Lighting — Adjustable Inground Light

Product Information

The LED Landscape Lighting – Adjustable Inground Light (Model OD-UGB201A) is designed for outdoor use. It should be used with low-voltage landscape power units that do not exceed 25 amps and have a maximum voltage of 15V. The luminaire must be installed in accordance with the National Electrical Code (NEC), Canadian Electrical Code (CEC), and local codes to ensure safety and warranty validity. The product should be mounted on non-combustible surfaces only.

Product Usage Instructions

WARNING: THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

1. Disconnect the transformer from the electrical supply before installation or service to prevent electric shock.

2. Dig a hole approximately 10 inches in diameter to a depth that allows the top of the fixture to be flush or positioned 1/8 inch above grade. It is recommended to use pea gravel or sand to aid in positioning the luminaire housing.
   CAUTION: When installing in sand or soil, the plastic well MUST be flush to 1/8 inch above grade to promote water runoff.

3. Remove the lens cover, lens, and rubber gasket.

4. Pull enough wires through to make manual connections with silicone-filled safety connectors. These connections should be made 4 to 6 inches above the top rim of the luminaire.

5. Coil the wire leads along the bottom of the plastic well and close the wiring compartment.

6. Install a lamp with the correct wattage and type as marked on the fixture label. Set the lamp at the desired aiming angle.

CAUTION : Failure to remove all dirt and debris from the gasket sealing surface may cause leakage and void the warranty. If you have any doubts about the installation or use of this product, consult a competent electrician.

• Contact Information:
• Email: info@ortechindustries.com
• Website: www.ortechindustries.ca
• Address: 13376 Comber Way Surrey BC V3W 5V9
• Address: 205 Summerlea Rd Brampton, ON L6T 4E5
• Phone: 1-888-543-6473 (BC) / 1-888-541-6474 (ON)

WARNING

WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

1. LED Adjustable Inground Lights are for outdoor use only with low voltage landscape power units that do not exceed 25 amps, 15V maximum
2. Luminaires MUST be installed in accordance with the National Electrical Code (NEC), Canadian Electrical Code (CEC), and local codes. Failure to do so will void the warranty and may result in serious injury and/or damage to the luminaire
3. Mount the luminaire in or on non-combustible mounting surfaces only

Application Notice

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE INSTRUCTIONS BELOW:

1. Keep away from combustibles. Turn OFF / unplug to change the lamp. DO NOT touch the lamp and replace it after servicing
2. DO NOT operate the LED Adjustable Inground Light fitted with a missing or damaged shield (Exception — Reference to a shield is able to be replaced with equivalent wording)
3. Install all luminaires 10 feet (3.05m) or more from a pool, spa, or fountain
4. DO NOT touch the lamp directly at any time. Use a soft cloth. Oil from the skin may damage the lamp
5. ALWAYS use UL, cUL, and CSA-recognized wire connectors for connections
6. DO NOT touch the hot lens, guard, or enclosure

CAUTION

PLEASE READ THE INSTRUCTIONS BEFORE COMMENCING INSTALLATION AND RETAIN THEM FOR FUTURE REFERENCE.
Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician.

INSTALLATION GUIDE

Luminaire Mounting (in ground)

1. To prevent electric shock, disconnect the transformer from the electrical supply before  installation or service
2. Dig a hole approximately 10″ in diameter to a depth suitable to make a top or fixture flush to 1/8″ above grade. Pea gravel or sand is recommended for seating the luminaire housing to aid positioning When installing in sand or soil, the plastic well MUST be flush to 1/8″ above grade to promote water runoff.
3. Remove the lens cover, lens, and rubber gasket
4. Pull wires through enough to make manual connections with silicone-filled safety connectors (4″ to 6″ above the top rim of the luminaire)
5. The coil wire leads along the bottom of the plastic well and closes the wiring compartment
6. Install the lamp with the correct wattage and type marked on the fixture label and set the lamp at desired aiming angle Failure to remove all dirt and debris from the gasket sealing surface may cause  leakage and void the warranty

info@ortechindustries.com www.ortechindustries.ca13376 Comber Way Surrey BC V3W 5V9

References

• Led Lighting, Electrical and Hvac Supplier Ortech Industries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>